B68L Wireless Gateway Quick Start
96722754_01
1 Getting to know your B68L Power button WPS button Press and hold for about 3 seconds to power the B68L on or off. Press and hold for 3 or more seconds to active WPS connection when Wi-Fi is turned on. LAN port Connect to computer, switch, or other LAN device. Power port Connect to compatible power adapter. Telephone port Connect to telephone. External antenna port Connect to external antenna.
Fast red blinking: no SIM/USIM card is found, the PIN is not verified, or the SIM/USIM card is not working properly. Network mode indicator Steady yellow: registered with a 3G/2G network. Steady green: connected to the Internet. Off: no signal. Steady on: Wi-Fi turned on or data transfer in progress. Wi-Fi/WPS indicator Blinking: a WPS connection is being set up. Off: Wi-Fi turned off. On: the B68L is powered on. Power indicator Off: the B68L is powered off.
2 Installation Installing the SIM/USIM card 1. Slide off the card slot cover. 2. Insert the SIM/USIM card into the card slot. Ensure that the beveled edge of the SIM/USIM card aligns with that of the card slot. 3. Close the card slot cover. Before removing the SIM/USIM card, ensure that the B68L is powered off and disconnected from the power outlet. (Optional) Installing the table stand The table stand is an optional accessory, and may not included in the packaging box.
Reset (Optional) Installing the external antenna The external antenna is an optional accessory, and may not included in the packaging box. If required, please contact your local dealer purchase it. Before installing the external antenna, ensure that the B68L is powered off and disconnected from the power outlet. Only use the external antenna indoors, and do not use it during thunderstorm. Do not change another unexpected antenna unless manufacture provide.
Connecting cables To prevent interference caused by radio signals, place the B68L at least 1 meter (3.28 feet) away from telephone and other electrical devices. Once connected to a power outlet, the B68L automatically powers on. Power adapter Telephone Computer Laptop, tablet, or smart phone Do not connect the B68L to the telephone wall outlet (or any Public Switched Telephone Network), because doing so could damage the B68L due to excessive heat.
3 Setting up a Wi-Fi connection Make sure your client (computer, tablet, or smart phone) also supports Wi-Fi. Turning on Wi-Fi on the B68L When the indicator is steady on, the Wi-Fi of the B68L is turned on. To manually turn Wi-Fi on, log in to the web management page (default address: http://192.168.1.1, default password: admin), and choose Home Network > WLAN Settings. On the displayed page, select Enable WLAN 2.4 GHz and click Save.
2. A dialog box is displayed, and the computer scans for available wireless networks within range. From the search results, select the wireless network with the same SSID as the B68L, and click Connect. 3. In the Connect to a Network dialog box, enter the B68L's Wi-Fi key, and click OK. Note that the Wi-Fi key is case sensitive. 4. When Connected is displayed next to the B68L's SSID, the PC is connected to the wireless network. On Mac OS 1. Click on the status bar on the Mac desktop.
2. The Mac then scans for available wireless networks within range. From the search results, select the wireless network with the same SSID as the B68L. 3. In the displayed dialog box, enter the B68L's Wi-Fi key, and click Join. Note that the Wi-Fi key is case sensitive. 4. When a check mark appears next to the B68L's SSID, the Mac is connected to the wireless network. On Android 4.0 1. From the home screen, touch section, turn Wi-Fi on. > Settings.
2. Touch WLAN to display the settings screen. Your device then scans for available wireless networks within range. From the search results, touch the wireless network with the same SSID as the B68L. 3. In the displayed dialog box, enter the Wi-Fi key, and touch Connect. Note that the Wi-Fi key is case sensitive. 4. When Connected is displayed under the B68L's SSID, the device is connected to the wireless network.
Setting up a Wi-Fi connection through WPS If the client supports WPS, you can set up a WPS connection as follows: 1. Ensure that Wi-Fi is enabled on the client. 2. Press and hold the starts blinking. button for 3 or more seconds. The indicator then If you cannot active WPS connection by WPS button, log in to the web management page (default address: http://192.168.1.1, default password: admin), and choose Home Network > WLAN Access.
5 For More Help If you are experiencing any issues with the B68L: See What's this? information on the web management page. Restart the B68L. Restore the B68L to its factory settings. Contact your service provider. Please visit http://consumer.huawei.com/en/support/hotline for recently updated hotline and email address in your country or region. Figures in this guide are for your reference only. Specific models may vary slightly, contact your service provider for more detailed information.
6 Safety information This sect ion contains important information about the operation of your device. It also contains informat ion about how to use the device safely. Read this informat ion carefully before using your device. Electronic device Do not use your device if using the device is prohibited. Do not use the device if doing so causes danger or interference with other electronic devices.
danger caused by lightning. Ideal operating temperatures are 0°C to 45°C. Ideal storage temperatures are - 30°C to +60°C. Extreme heat or cold may damage your device or accessories. Keep the device and accessories in a well-ventilated and cool area away from direct sunlight. Do not enclose or cover your device with towels or other objects. Do not place the device in a container with poor heat dissipation, such as a box or bag.
Choose only accessories approved for use with this model by the device manufacturer. The use of any other types of accessories may void the warranty, may violate local regulat ions and laws, and may be dangerous. Please contact your retailer for information about the availability of approved accessories in your area. Power adapter safety The power plug is intended to serve as a disconnect device.
causing the device to malfunction. Before you clean or maintain the device, stop using it, stop all applications, and disconnect all cables connected to it. Do not use any chemical detergent, powder, or other chemical agents (such as alcohol and benzene) to clean the device or accessories. These substances may cause damage to parts or present a fire hazard. Use a clean, soft, and dry cloth to clean the device and accessories.
Reduction of hazardous substances This device is compliant with the REACH Regulat ion [Regulat ion (EC) No 1907/2006] and RoHS Direct ive Recast (Direct ive 2011/65/EU). Batteries (if included) are compliant with the Battery Directive (Directive 2006/66/EC). For up-to-date information about REACH and RoHS compliance, please visit the web site http://consumer.huawei.com/certificat ion. EU regulatory conformance Statement Hereby, Huawei Technologies Co., Ltd.
--Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operat ion is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operat ion. Caution: Any changes or modifications to this device not expressly approved by Huawei Technologies Co., Ltd.
DISCLAIMER ALL CONTENTS OF THIS MANUAL ARE PROVIDED "AS IS". EXCEPT AS REQUIRED BY APPLICABLE LAWS, NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE MADE IN RELATION TO THE ACCURACY, RELIABILITY OR CONTENTS OF THIS MANUAL.