B882-66 LTE Wireless Gateway Quick Start
96722859_01
1 Getting to know your B882-66 On: the B882-66 is powered on. Power indicator Off: the B882-66 is powered off. Blinking red: no USIM card is found, the PIN is not verified, or the USIM card is not working properly. Network mode indicator Steady cyan: registered with an LTE network. Steady blue: registered with a 3G network. Off: no signal. Steady on: Wi-Fi turned on or data transfer in progress. Wi-Fi/WPS indicator Blinking: a WPS connection is being set up. Off: Wi-Fi turned off.
Steady on: connected to a LTE/3G network. Wireless connection indicator Blinking: connecting to a LTE/3G network. Steady on: LAN port is connected to a client. / / Blinking: data is being transmitted through LAN port. LAN indicator Off: no client is connected to LAN port. Steady on: connected to an Ethernet network. Wired connection indicator Blinking: connecting to an Ethernet network. Install a USIM card to access to the Internet via a LTE/3G data connection.
Connect to telephone. Telephone port Power port Power button Connect to compatible power adapter. Press and hold for about 3 seconds to power the B882-66 on or off.
2 Installation Installing the USIM card Before installing or removing the USIM card, ensure that the B882-66 is powered off and disconnected from the power outlet. If you want to use LTE/3G wireless data service and voice service, please install the USIM card. 1. Pull out the card slot cover and rotate it to reveal the USIM card slot. 2. Partially insert the USIM card into the card slot. Ensure that the beveled edge of the USIM card aligns with that of the card slot.
Connecting cables To prevent interference caused by radio signals, place the B882-66 at least 1 meter (3.28 feet) away from telephone and other electrical devices. Once connected to a power outlet, the B882-66 automatically powers on. Ethernet port on the wall Computer Power adapter Laptop, tablet, or smart phone Telephone Do not connect the B882-66 to the telephone wall outlet (or any Public Switched Telephone Network), because doing so could damage the B882-66 due to excessive heat.
3 Setting up a Wi-Fi connection Make sure your client (computer, tablet, or smart phone) also supports Wi-Fi. Turning on Wi-Fi on the B882-66 When the indicator is steady on, the Wi-Fi of the B882-66 is turned on. To manually turn Wi-Fi on, press and hold the button for about 3 seconds. Recording the SSID and Wi-Fi key The default SSID and Wi-Fi key are printed on the B882-66's rear label.
Setting up a Wi-Fi connection from a client On Windows 7 1. Click on the status bar on the PC desktop. 2. A dialog box is displayed, and the computer scans for available wireless networks within range. From the search results, select the wireless network with the same SSID as the B882-66, and click Connect. 3. In the Connect to a Network dialog box, enter the B882-66's Wi-Fi key, and click OK. Note that the Wi-Fi key is case sensitive. 4.
On Mac OS 1. Click on the status bar on the Mac desktop. Choose Turn AirPort On from the displayed menu. 2. The Mac then scans for available wireless networks within range. From the search results, select the wireless network with the same SSID as the B882-66. 3. In the displayed dialog box, enter the B882-66's Wi-Fi key, and click Join. Note that the Wi-Fi key is case sensitive. 4. When a check mark appears next to the B882-66's SSID, the Mac is connected to the wireless network.
On Android 4.0 1. From the home screen, touch section, turn Wi-Fi on. > Settings. In the WIRELESS & NETWORKS 2. Touch WLAN to display the settings screen. Your device then scans for available wireless networks within range. From the search results, touch the wireless network with the same SSID as the B882-66. 3. In the displayed dialog box, enter the Wi-Fi key, and touch Connect. Note that the Wi-Fi key is case sensitive. 4.
Setting up a Wi-Fi connection through WPS If the client supports WPS, you can set up a WPS connection as follows: 1. Ensure that Wi-Fi is enabled on the client. 2. Press and hold the then starts blinking. button for 6 or more seconds. The indicator 3. Activate the WPS connection on the client in 2 minutes. For instructions about how to enable a WPS connection on the client, see the client's user guide. 4 Configuring your B882-66 1.
5 For More Help If you are experiencing any issues with the B882-66: Restart the B882-66. See the help information on the web management page. Restore the B882-66 to its factory settings. Contact your service provider. Please visit http://consumer.huawei.com/en/support/hotline for recently updated hotline and email address in your country or region. Figures in this guide are for your reference only. Specific models may vary slightly, contact your service provider for more detailed information.
6 Safety information This sect ion contains important information about the operation of your device. It also contains informat ion about how to use the device safely. Read this informat ion carefully before using your device. Electronic device Do not use your device if using the device is prohibited. Do not use the device if doing so causes danger or interference with other electronic devices.
danger caused by lightning. Ideal operating temperatures are 0°C to 45°C. Ideal storage temperatures are - 30°C to +60°C. Extreme heat or cold may damage your device or accessories. Keep the device and accessories in a well-ventilated and cool area away from direct sunlight. Do not enclose or cover your device with towels or other objects. Do not place the device in a container with poor heat dissipation, such as a box or bag.
Accessories Using an unapproved or incompatible power adapter, charger or battery may cause fire, explosion or other hazards. Choose only accessories approved for use with this model by the device manufacturer. The use of any other types of accessories may void the warranty, may violate local regulat ions and laws, and may be dangerous. Please contact your retailer for information about the availability of approved accessories in your area.
sound or smell), immediately stop using it, power it off, remove all cables connected to it, and contact an authorized service center. Do not trample, pull, or excessively bend any cable. Doing so may damage the cable, causing the device to malfunction. Before you clean or maintain the device, stop using it, stop all applications, and disconnect all cables connected to it.
--Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules.
7 Legal Notice Copyright © Huawei Technologies Co., Ltd. 2014. All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. and its affiliates ("Huawei"). The product described in this manual may include copyrighted software of Huawei and possible licensors.
GOODWILL SAVINGS OR ANTICIPATED SAVINGS REGARDLESS OF WHETHER SUCH LOSSES ARE FORSEEABLE OR NOT. THE MAXIMUM LIABILITY (THIS LIMITATION SHALL NOT APPLY TO LIABILITY FOR PERSONAL INJURY TO THE EXTENT APPLICABLE LAW PROHIBITS SUCH A LIMITATION) OF HUAWEI ARISING FROM THE USE OF THE PRODUCT DESCRIBED IN THIS MANUAL SHALL BE LIMITED TO THE AMOUNT PAID BY CUSTOMERS FOR THE PURCHASE OF THIS PRODUCT.
