Thank you for choosing HUAWEI E5 Wireless Terminal (Hereinafter referred to as E5). Note: z The supported functions and actual appearance are subject to your product purchased. The following pictures are displayed for illustration purpose only. For details of your product selection, consult your service provider. z This guide briefly describes the function of the E5. For the operation of configuring the management parameters, see Help on the web management page.
Get to Know Your E5 Appearance No.
z WPS: WiFi Protected Setup Screen No.
No.
Install the SIM Card and Battery Position the card at the card slot entrance, making sure it is facing the same way as shown in the diagram, with the notched corner at the top left. Then slide in.
How to Access the Internet with WiFi Note: By default, the management parameters are preset on the E5 according to the requirements from the service provider. You can follow the steps below to quickly access the Internet. For the details about how to set the management parameters, see the Help on the Web management page. Step1: Power on the E5 Step2: Establish the WiFi Connection Step3: Access the Internet 1.
becomes lightened; the E5 is powered on. Note: Press and hold until the screen is off; the E5 is powered off. 2. Establish the WiFi Connection (Take PC for Example) 1. Make sure that the WiFi is enabled. 2. Select Start > Control Panel > Network Connections > Wireless Network Connection. Note: To set up a WiFi connection, the PC must be configured with the wireless network adapter. If the wireless network connection is displayed, the wireless network adapter is available.
Networks to display the wireless network connection list. 4. Select the network connection that the SSID is the same as that of the E5, and then click . Note: z If the encryption parameter is set for the E5, the Wireless Network Connection dialog box is displayed and requires the network key and confirmation. z The SSID and key label is attached on the E5. Wait for a while. The wireless connection icon displays in the status area in the lower right corner of the screen. Then, your PC can connect to the E5.
3. Access the Internet After you establish the WiFi connection successfully, you can access the Internet using the following two modes. By default, the mode is On Demand. Mode Operations On Demand After the E5 is powered on, it can automatically connect to the Internet when data transmission is required. If data transmission is not performed over a period of time, the E5 automatically tears down the Internet connection.
Mode Operations Press and hold CONNECT until is off, the connection is tore down. Note: You can also launch web management page to connect to or disconnect from the network following the prompts. Note: z You can launch the web management page to select the mode of accessing the Internet. z If the E5 accesses the roaming network, the E5 automatically tears down the established network connection.
How to Access the Web Management Page 1. Make sure that the connection between the E5 and the WiFi device or computer is normal. 2. Start the Internet browser and enter http://192.168.1.1 in the address bar. 3. Enter the password, and then click Login. Note: The default password is admin.
Everyday Use Charging the Battery Note: If you have not used the battery for a long time, please recharge it first. Method 1: Using the charger Caution: z Use the compatible charger (5V, 650mA) delivered only by the manufacturer with this E5 model. Using charger of other device model, other manufacturers or vendors may invalidate any approval or warranty applicable to the E5, result in the non-operation of the E5, and cause danger. z Charger is an optional accessory.
2. Connect the E5 and PC with the compatible data cable. Saving Power mode If the E5 has not been carried out any operations for a while, the screen is off. If the E5 has not been accessed for 10 minutes by default, the E5 changes to the deep sleep state. z When the E5 is in the deep sleep state, you can press any key to activate the E5. Now the screen becomes lightened. z When the E5 is in the deep sleep state, the WiFi is automatically disabled.
z Note: Press and hold until is off, the WiFi is disabled. Establishing the WPS Connection If the WiFi Clients connected with the E5 support the WPS, the E5 can automatically generate a network key without manually entering. The operation steps of WPS connection are as follows. 1. Power on the E5. 2. Start the Clients connected with the E5. 3. Enable the WPS of the E5. Note: After the WiFi is enabled, press and hold . When is off, is displayed on the screen, the WPS of the E5 is enabled. and then 4.
When the PIN code protection is enabled, you need launch the Web Management Page and then click Connection to enter the correct PIN code following the page prompts. Both the PIN and PUK are delivered with the SIM card. For details, consult your service provider. For the operation of accessing the Web Management Page, see “ How to Access the Web Management Page ”. Multi-device Access The WiFi device or computer can be connected to the Internet through the E5.
Micro SD Card 1. Remove the rubber cap from the Micro SD card slot. Then insert the Micro SD card into the slot. 2. After inserting the Micro SD card completely, replace the rubber cap. Note: z Micro SD card is an optional accessory. If the Micro SD card is not provided in the package, you can buy one yourself. z To remove the Micro SD card, open the rubber cap and press the Micro SD card gently. Now the Micro SD card will pop up automatically. Then take it out.
If you forget the changes of some parameters, you can choose to restore factory defaults and reconfigure the E5. Press and hold and CONNECT at the same time until the screen is off, you restore the factory defaults successfully. Note: After this operation, all personal configuration settings are deleted and all web-based management settings and parameters will be restored to their default values.
Version: V100R001_01 Part Number: 31010CBT 20
