Thank you for choosing HUAWEI EC5805 Wireless Modem (hereinafter referred to as the EC5805). z z z The supported functions and actual appearance are subject to your product purchased. The following pictures are provided for illustration only. For details about your product selection, consult your service provider. This guide briefly describes the functions of the EC5805. For details about how to set the management parameters, see the Help on the web management page.
Getting to Know Your EC5805 Packing List The package box contains the following items. If any of the items is lost or damaged, contact your local dealer.
your local dealer to buy them yourself.
Application Scenarios The Wi-Fi device or computer can be connected to the Internet through the EC5805. The actual connecting procedure depends on the operating system of the Wi-Fi device or computer. You can perform the connection operations as prompted.
Scenario 3: Multi-device access via Wi-Fi and USB at the same time Smart phone Game machine Digital camera Laptop Appearance 4
No . 1 2 3 4 Item Wi-Fi/WP S indicator Wi-Fi/WP S button Power button No .
Indicat or Status z Wi-Fi/ WPS z z z Power z z z z Signal Off: The Wi-Fi and WPS are disabled. Continuously on in green: The Wi-Fi is enabled. Blinking in green: The WPS is enabled. Blinking in red: The battery power level is very low and must be charged immediately; otherwise the EC5805 will be powered off. Continuously on in red: The battery power level is weak. Blinking in green: The battery is being charged. Continuously on in green: The battery power level is enough.
Indicat or Status Continuously on in green: The EC5805 is in the normal state. z Continuously on in blue: The EC5805 is in the roaming state. z Fast blinking in green: dialing up in the normal state. z Fast blinking in blue: dialing up in the roaming state. Wi-Fi: Wireless Fidelity WPS: Wi-Fi Protected Setup z z z Before You Start Installing the Battery Install the battery as shown in the following figure.
1 2 3 Installing the microSD Card 1. Remove the rubber cap from the microSD card slot. Then insert the microSD card into the slot. 2. After inserting the microSD card completely, attach the rubber cap. Note: z The microSD card is an optional accessory. If the microSD card is not provided in the package, you can buy one yourself. z To remove the microSD card, open the rubber cap and press the microSD card gently.
z automatically, take it out. Do not remove the card when it is being used. Otherwise, the card and the EC5805 may be damaged, and the data stored on the card may be corrupted. Charging the Battery Note: If you have not used the battery for a long time, please charge it first. Method 1: Charging by Using the Charger Caution: z Use the charger compatible the EC5805 model and provided by the designated manufacturers only.
z vendors is used, the EC5805 may fail to work and dangers may be caused. At the same time, any national regulations on terminal products or warranty applicable to the EC5805 may fail to work. The charger is an optional accessory. If the charger is not provided in the package, you can contact your local dealer to buy one yourself. Method 2: Charging by Connecting to a PC 1. Power off the EC5805. 2. Connect the EC5805 and PC with a compatible data cable.
parameters are preset on the EC5805 according to the requirements of the service provider. You can follow the steps below to quickly access the Internet. For the details about how to set the management parameters, see the Help on the Web management page. Step1: Power on the EC5805. Step2: Establish a Wi-Fi Connection. Step3: Access the Internet. 1. Power on the EC5805 Press and hold Power button until the indicators become lightened, the EC5805 is powered on.
continuously on in green. 2. Select Start > Control Panel > Network Connections > Wireless Network Connection. Note: To set up a Wi-Fi connection, the PC must be configured with a wireless network adapter. If Wireless Network Connection is displayed, the wireless network adapter is available. Otherwise, you need to check your wireless network adapter. 3. Click View available Wireless Networks to display the wireless network list. 4.
Note: If the encryption parameter is already z set for the EC5805, the Wireless Network Connection dialog box is displayed and requires the network key and confirmation. z The SSID and key label is attached on the EC5805.
Wait until the wireless connection icon is displayed in the status area in the lower right corner of the screen. Then, you can connect your PC to the EC5805. 3. Access the Internet After you establish a Wi-Fi connection successfully, you can access the Internet in either of the following two modes. By default, the mode is On Demand. Mode Operations On Deman d Manual After the EC5805 is powered on, it can automatically connect to the network when data transmission is required.
Note: z You can launch the web management page to select the mode of accessing the Internet. z If the EC5805 accesses the roaming network, the EC5805 automatically disconnects from the established network connection. Accessing the Internet Through a USB Connection 1. Power on the EC5805. 2. Connect the EC5805 to PC using the compatible USB data cable. 3. The operating system automatically detects and recognizes new hardware. 4.
3. Enter the password, and then click Login. Note: z The default user name is cricket. z The default password is 0000. Phonebook You can enjoy phonebook service on the web management page. 1. Access the web management page. 2. Click Phonebook to manage contacts. SMS You can enjoy the short message (SMS) service on the web management page. 1. Access the web management page. 2. Click SMS to view, create, reply, or send a message.
When the EC5805 is in the deep sleep state, you can press any key to activate the EC5805. If the EC5805 is activated, the indicators become lightened. Enabling/Disabling the Wi-Fi Function Press and hold Wi-Fi/WPS button until Wi-Fi/WPS indicator is continuously on in green, the Wi-Fi is enabled. Note: Press and hold Wi-Fi/WPS button until Wi-Fi/WPS indicator is off, the Wi-Fi is disabled.
4. Enable the WPS function of the Clients. Note: For the Wi-Fi operations of the Clients, see the Clients’ user guide. Restoring the Factory Defaults If you forget the changes of some parameters, you can choose to restore factory defaults and reconfigure the EC5805. Reset: Press and hold it until all the indicators are off, you restore the factory defaults successfully.
can try the following ways: z See Help on the web management page. z Restart the EC5805. z Restore the factory defaults. z Contact your service provider. Example: Wi-Fi Connection to Game Machine (PSP) 1. Turn on the PSP WLAN switch. 2. Select Settings > Network Settings. 3. Select Infrastructure Mode to connect your local Wi-Fi access point. 4. Select New Connection to specify a mnemonic connection name (such as MyEC5805). 5. Select Scan to detect networks in range.
6. Select the SSID same as that of the EC5805. Then press the > button consecutively to confirm the SSID and input the Wi-Fi key. SSID: The Wi-Fi name of the EC5805. WEP: The Wi-Fi key of the EC5805 The default SSID and key label is z attached on the EC5805. 7. Press the > button to continue, and then press X to save settings. 8. Select Test Connection to check the connection.
congratulations! you're online! 9. Now, you can go to Internet Browser. Example: Wi-Fi Connection to Smart Phone (iPhone) 1. Select Settings > Wi-Fi and turn Wi-Fi on. 2. Automatically detect networks in range, then display the access point list.
3. Select a network whose name is the same as that of the EC5805. 4. If necessary, enter a password and tap Join. (Networks requiring a password appear with a lock icon.) Note: The Wi-Fi Clients such as iTouch, PS3, and NDS can also access Internet via the EC5805. For details about the operation, follow the user guides of the Wi-Fi Clients.
What can I do if the Client connected to the EC5805 cannot access the Internet? 1. Check and ensure that the Client is connected to the EC5805 properly. 2. Check the power status to ensure that the EC5805 is powered on. 3. Check the signal strength to ensure that the area is covered by the network. 4. Check that the network mode is correct. For details about network modes, see Mobile Network Settings on the web management page. 5.
management page. 7. Check that the network adapter of your Client runs properly. 8. If the problem still persists, please consult you service provider. What can I do if the Client cannot access the WLAN? 1. If there are interferences or shields near the EC5805, you can adjust the position of the EC5805. 2. Check and record the following settings of your Client and your EC5805: SSID, WEP type, and key. The SSID of the Client must be ANY or the same as that of the EC5805.
Version: V100R001_01 Part Number: 3101XXXX 25
