Notice Copyright © 2008 Huawei Technologies Co., Ltd. manual do not constitute the warranty of any kind, expressed or implied. Huawei Technologies Co., Ltd. All Rights Reserved 1 No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. 2 Trademarks 3 and HUAWEI are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this manual are the property of their respective holders.
1 Table of Contents Table of Contents 1 Introduction 1 Packing List ................................................1 Front View ..................................................1 Rear View...................................................2 Installation 3 Installing the Battery...................................3 Installing the UIM Card...............................3 Installing the Power Adapter ......................4 Installing the Indoor Antenna......................4 Connecting the Terminal .......
1 Introduction Packing List Item Quantity FWT host 1 Power adapter 1 Phone cable 1 Battery (Rechargeable) 1 Certificate of Quality 1 User Guide 1 8 1 local radio signal strength helps you Note • The select an indoor antenna. • To access the Internet, you need to purchase the required data suite. For more information, please consult your local sales agent. Front View figures are only for your reference, please Note The refer color and shape to product.
Rear View NO. Item 7 Signal strength indicators: More indicators indicate stronger signal strength. 8 Battery indicator Rear View 1 The battery serves as the only power supply (without external power adapter): • In blue: The battery is in full electricity. • In red: The battery is in medium electricity. • In red with blinking: The battery needs to be recharged. The external power adapter is in use (with the battery inside): • In red: The battery is being charged.
2 Installation Before installing or removing the battery, indoor Note antenna, or R-UIM card, you need to swich off the FWT and disconnect the FWT from the power adapter. To prevent lighting from injuring human body. the ambient temperature exceeds the Note • When temparature allowed for charging, the system will stop charging the battery. • When the power adapter is in use, the FWT will automatically charge the battery and stop charging when the battery is fully charged.
Installing the Power Adapter Installing the Power Adapter In normal conditions, the FWT relies on the external power adapter for power supply. 1 Make sure that the FWT is switched off. 2 Insert one end of the power adapter into the DC input port, and the other end into the power supply jack. 3 Switch on the FWT and wait for a few seconds. If the power indicator is in blue, the connection is correct.
Connecting the Terminal Connecting the FWT to a Telephone The FWT provides two telephone ports. They are in parallel connection and use the same number. 2 Connecting the FWT to a Facsimile Set Installation Connecting the FWT to a PC After purchasing the data service suite, you can use data services by connecting the FWT to a PC, and maintain and debug the FWT on the PC. For details, consult your local agent. affirm that your FWT supports facsimile Note Please before using this function.
Viewing the Signal Strength Viewing the Signal Strength Power on the FWT and wait until some signal strength indicators are on or until you can hear the dial tone. • If all signal strength indicators remain off for 5 minutes and only the re-dial tone is heard. No signals can be received. • Turn the antenna but all signal LEDs still keep off. The signal quality is very poor. If the dial tone can be heard in some area, position the antenna towards it.
3 General Functions Booting the FWT The boot process of the FWT will last about 20 seconds. Then you can view the signal strength. the signal strength indicators remain off, the Note IfFWT may be faulty or the network is not covered the area. Please consult the local agent. 1 Before off-hook, make sure at least one signal strength LED is on. 2 Dial the number in either of the following ways: • Dial a telephone number in a regular way, and the number will be dialed out in several seconds.
Adjusting the Voice Volume Adjusting the Volume in Standby Mode make the setting after hearing the dial tone again. Adjusting the Volume During a Call 1 Hook off and you can hear the dial tone, which means the telephone service is available. 2 Press ##1 to adjust the volume. 3 Press keys from 1 to 4 to select the desired volumn. The keys from 1 to 4 represents volumn level from 1 to 4. 4 After selecting the desired volume, press * key to save it.
4 Advanced Functions Supplementary Services You need the network carrier to enable the services. Here are several typical services for your reference: Three-Way Calling, Call Transfer, Call Forwarding, Emergency Call. Configuring the Network Connection Before accessing the Internet, you need to configure the network connection. If you want to apply the default settings, you can skip operations in this section. Click Properties, enter the phone number (by default, the phone number is #777.
Facsimile Function (Optional) Dialing Up to the Internet Select a connection or create a new connection. Then Click Connect. If the user name and password are correct, you can connect to the Internet. connection rate shown after the dial-up is Note The connected may be the connection rate of the data port. For details, consult your carrier. Facsimile Function (Optional) function requires the network support. Note • The The success rate of sending or receiving is receive a facsimile.
5 Troubleshooting Following the "Adjusting the Volume during a call" Check if the FWT is in facisimile receive mode. Please exit from this mode first. Sending a facsimile fails (pressing the send key after hearing the sound of "toot") It may be caused by the following reasons: 1. The network signal is weak. 2. You have dialed a wrong fax number. 3. The called party has configured manually receiving mode but not started receiving. 4. The called party is busy. The handfree function cannot be used.
6 Warnings and Precautions To use the FWT correctly and safely, read the following cautions and let your children know these before using the FWT. Basic Cautions • According to the packing list, check items in the package box to make sure that they are complete and undamaged. • Before installing and using the FWT, read this user guide carefully Electronic Device Power off your FWT near high-precision electronic devices. The FWT may affect the performance of these devices.
• Your FWT is designed to conform to the authoritative inter- • The network signal condition will directly affect the quality and stability of the call. Consequently, you should place the FWT in a place where it can receive network signal well. Do not put FWT in a building with an iron or metal roof. The distance between FWT and other metal materials (such as metal brackets or metal doors and windows) should be greater than 25cm and the distance between FWTs should be greater than 30cm.
• Do not disassemble the battery or solder the battery poles. Otherwise, fluid leakage, overheat, fire, or explosion may result. • If the liquid such as water comes into the power adapter accidentally, remove the plug of the power adapter from the socket immediately. • If there is battery leakage, smoke, or strange smell, stop using the battery and keep it away from open flame to avoid fire or explosion. • Disconnect the power adapter and take out the battery when the FWT is not used for a long time.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 6 Warnings and Precautions This equipment has been tested and found to comply with the limits for a Class B digital Device, pursuant to Part 15 of the FCC rules.