User's Manual
Table Of Contents
- About This Document
- Contents
- 1 Safety Information
- 2 Product Overview
- 3 Device Installation
- 4 Cable Connections
- 4.1 Connecting Cables to the SmartLogger
- 4.1.1 Preparing Cables
- 4.1.2 Connecting a PE Cable
- 4.1.3 Connecting an RS485 Communications Cable
- 4.1.4 Connecting an MBUS Cable
- 4.1.5 Connecting a DI Signal Cable
- 4.1.6 Connecting the Output Power Cable
- 4.1.7 Connecting the AI Signal Cable
- 4.1.8 Connecting the DO Signal Cable
- 4.1.9 Connecting the Ethernet Cable
- 4.1.10 Connecting Fiber Jumpers
- 4.1.11 Installing a SIM Card and a 4G Antenna
- 4.1.12 Connecting the 24 V Input Power Cable
- 4.2 Connecting Cables to the SmartModule
- 4.2.1 Preparing Cables
- 4.2.2 Connecting the PE Cable
- 4.2.3 Connecting the Ethernet Cable
- 4.2.4 Connecting the 12 V Power Input Cable
- 4.2.5 Connecting the RS485 Communications Cable
- 4.2.6 Connecting the DI Signal Cable
- 4.2.7 Connecting the Output Power Cable
- 4.2.8 Connecting the AI Signal Cable
- 4.2.9 Connecting the PT Signal Cable
- 4.2.10 Connecting the 24 V Power Input Cable
- 4.1 Connecting Cables to the SmartLogger
- 5 System Operation
- 6 WebUI Operations
- 6.1 Introduction to WebUI
- 6.2 Device Commissioning
- 6.3 Parameter Settings
- 6.3.1 Setting User Parameters
- 6.3.2 Setting Parameters for Connecting to the Management System
- 6.3.3 Setting RS485 Communications Parameters
- 6.3.4 Setting Parameters for the Slave SmartLogger
- 6.3.5 Setting MBUS Parameters
- 6.3.6 Setting SUN2000 Parameters
- 6.3.7 Setting PID Module Parameters
- 6.3.8 Setting Power Meter Parameters
- 6.3.9 Setting EMI Parameters
- 6.3.10 Setting STS Parameters
- 6.3.11 Setting IEC103 Device Parameters
- 6.3.12 Setting Parameters for a Custom Device
- 6.3.13 Setting IEC104 Device Parameters
- 6.4 Power Grid Scheduling
- 7 Device Maintenance
- 8 FAQ
- 8.1 How Do I Connect the SmartLogger to the SUN2000 App or FusionSolar App?
- 8.2 How Do I Set FTP Parameters?
- 8.3 How Do I Set Email Parameters?
- 8.4 How Do I Change the SSID and Password of the Built-in WLAN?
- 8.5 How Do I Use DI Ports?
- 8.6 How Do I Use DO Ports?
- 8.7 How Do I Use the USB Port?
- 8.8 How Do I Change a Device Name?
- 8.9 How Do I Change the Communications Address?
- 8.10 How Do I Export Inverter Parameters?
- 8.11 How Do I Clear Alarms?
- 8.12 How Do I Enable the AI1 Port to Detect SPD Alarms?
- 8.13 Which Models of Power Meters and EMIs Are Supported by the SmartLogger?
- 8.14 How Do I Check the SIM Card Status?
- 9 Technical Specifications
- A Product User Lists
- B Domain Name List of Management Systems
- C Acronyms and Abbreviations
SmartLogger3000
User Manual
9 Technical Specifications
Issue 04 (2020-03-11)
Copyright © Huawei Technologies Co., Ltd.
174
Parameter
Specifications
Dimensions (W x H x D)
259 mm x 160 mm x 59 mm (including
mounting ears)
225 mm x 160 mm x 44 mm (excluding
mounting ears)
Net weight
2 kg
Operating temperature
–40°C to +60°C
Storage temperature
–40°C to +70°C
Relative humidity
5%–95% RH
IP rating
IP20
Installation mode
Installed on a wall or guide rail
Highest operating altitude
4000 m
Pollution degree
2
Corrosion level
Class B
Ports
Parameter
Specifications
Ethernet electrical port (WAN and
LAN)
2 PCS; 10M/100M/1000M auto-negotiation
Ethernet optical port (SFP)
2 PCS; supports 100M/1000M SFP/eSFP optical
modules
MBUS port
1 PCS; supports an AC input voltage of 800 V at
most
RS485 (COM) port
3 PCS; supported baud rates: 1200 bit/s, 2400
bit/s, 4800 bit/s, 9600 bit/s, 19,200 bit/s, and
115,200 bit/s
USB port
USB2.0
Power output port
1 PCS; DC output: 12 V, 0.1 A
Digital input (DI) port
4 PCS; supports only the access from relay dry
contacts
Digital output (DO) port
2 PCS; relay dry contact output ports, supporting
NO or NC contacts; supports 12 V, 0.5 A signal
voltage
Analog input (AI) port
4 PCS; AI1: supports 0–10 V voltage (passive);
AI2–AI4: support 4–20 mA or 0–20 mA input
current (passive)