User's Manual
Table Of Contents
- About This Document
- Contents
- 1 Safety Information
- 2 Product Overview
- 3 Device Installation
- 4 Cable Connections
- 4.1 Connecting Cables to the SmartLogger
- 4.1.1 Preparing Cables
- 4.1.2 Connecting a PE Cable
- 4.1.3 Connecting an RS485 Communications Cable
- 4.1.4 Connecting an MBUS Cable
- 4.1.5 Connecting a DI Signal Cable
- 4.1.6 Connecting the Output Power Cable
- 4.1.7 Connecting the AI Signal Cable
- 4.1.8 Connecting the DO Signal Cable
- 4.1.9 Connecting the Ethernet Cable
- 4.1.10 Connecting Fiber Jumpers
- 4.1.11 Installing a SIM Card and a 4G Antenna
- 4.1.12 Connecting the 24 V Input Power Cable
- 4.2 Connecting Cables to the SmartModule
- 4.2.1 Preparing Cables
- 4.2.2 Connecting the PE Cable
- 4.2.3 Connecting the Ethernet Cable
- 4.2.4 Connecting the 12 V Power Input Cable
- 4.2.5 Connecting the RS485 Communications Cable
- 4.2.6 Connecting the DI Signal Cable
- 4.2.7 Connecting the Output Power Cable
- 4.2.8 Connecting the AI Signal Cable
- 4.2.9 Connecting the PT Signal Cable
- 4.2.10 Connecting the 24 V Power Input Cable
- 4.1 Connecting Cables to the SmartLogger
- 5 System Operation
- 6 WebUI Operations
- 6.1 Introduction to WebUI
- 6.2 Device Commissioning
- 6.3 Parameter Settings
- 6.3.1 Setting User Parameters
- 6.3.2 Setting Parameters for Connecting to the Management System
- 6.3.3 Setting RS485 Communications Parameters
- 6.3.4 Setting Parameters for the Slave SmartLogger
- 6.3.5 Setting MBUS Parameters
- 6.3.6 Setting SUN2000 Parameters
- 6.3.7 Setting PID Module Parameters
- 6.3.8 Setting Power Meter Parameters
- 6.3.9 Setting EMI Parameters
- 6.3.10 Setting STS Parameters
- 6.3.11 Setting IEC103 Device Parameters
- 6.3.12 Setting Parameters for a Custom Device
- 6.3.13 Setting IEC104 Device Parameters
- 6.4 Power Grid Scheduling
- 7 Device Maintenance
- 8 FAQ
- 8.1 How Do I Connect the SmartLogger to the SUN2000 App or FusionSolar App?
- 8.2 How Do I Set FTP Parameters?
- 8.3 How Do I Set Email Parameters?
- 8.4 How Do I Change the SSID and Password of the Built-in WLAN?
- 8.5 How Do I Use DI Ports?
- 8.6 How Do I Use DO Ports?
- 8.7 How Do I Use the USB Port?
- 8.8 How Do I Change a Device Name?
- 8.9 How Do I Change the Communications Address?
- 8.10 How Do I Export Inverter Parameters?
- 8.11 How Do I Clear Alarms?
- 8.12 How Do I Enable the AI1 Port to Detect SPD Alarms?
- 8.13 Which Models of Power Meters and EMIs Are Supported by the SmartLogger?
- 8.14 How Do I Check the SIM Card Status?
- 9 Technical Specifications
- A Product User Lists
- B Domain Name List of Management Systems
- C Acronyms and Abbreviations
SmartLogger3000
User Manual
9 Technical Specifications
Issue 04 (2020-03-11)
Copyright © Huawei Technologies Co., Ltd.
175
Parameter
Specifications
4G antenna port (4G)
1 PCS; SMA-K (external screw inner hole) port,
used with the antenna with the SMA-J (internal
screw inner pin) port
Wireless Communication
Parameter
Specifications
4G/3G/2G
The SmartLogger3000A01CN supports 2G, 3G,
and 4G networks of China Mobile and China
Unicom as well as 4G networks of China
Telecom.
The following frequency bands are supported:
LTE FDD: B1, B3, B8
LTE TDD: B38, B39, B40, B41
WCDMA: B1, B5, B8, B9
TD-SCDMA: B34, B39
GSM: 900 MHz/1800 MHz
The SmartLogger3000A01EU and
SmartLogger3000A03EU support the following
frequency bands:
LTE FDD: B1, B3, B5, B7, B8, B20
LTE TDD: B38, B40, B41
WCDMA: B1, B5, B8
GSM: 900 MHz/1800 MHz
SmartLogger3000A01NH: Supports 3G/4G of
Docomo and SoftBank.
The following frequency bands are supported:
LTE FDD: B1, B3, B8, B18, B19, B26 (only
Tokyo, Nagoya, and Osaka support B3)
LTE TDD: B41
WCDMA: B1, B6, B8, B19
The SmartLogger3000A01KR supports
networks of SK Telecom.
The following frequency bands are supported:
LTE FDD: B1, B3, B5, B7
WCDMA: B1