User's Manual
Table Of Contents
- About This Document
- Contents
- 1 Safety Information
- 2 Product Overview
- 3 Device Installation
- 4 Cable Connections
- 4.1 Connecting Cables to the SmartLogger
- 4.1.1 Preparing Cables
- 4.1.2 Connecting a PE Cable
- 4.1.3 Connecting an RS485 Communications Cable
- 4.1.4 Connecting an MBUS Cable
- 4.1.5 Connecting a DI Signal Cable
- 4.1.6 Connecting the Output Power Cable
- 4.1.7 Connecting the AI Signal Cable
- 4.1.8 Connecting the DO Signal Cable
- 4.1.9 Connecting the Ethernet Cable
- 4.1.10 Connecting Fiber Jumpers
- 4.1.11 Installing a SIM Card and a 4G Antenna
- 4.1.12 Connecting the 24 V Input Power Cable
- 4.2 Connecting Cables to the SmartModule
- 4.2.1 Preparing Cables
- 4.2.2 Connecting the PE Cable
- 4.2.3 Connecting the Ethernet Cable
- 4.2.4 Connecting the 12 V Power Input Cable
- 4.2.5 Connecting the RS485 Communications Cable
- 4.2.6 Connecting the DI Signal Cable
- 4.2.7 Connecting the Output Power Cable
- 4.2.8 Connecting the AI Signal Cable
- 4.2.9 Connecting the PT Signal Cable
- 4.2.10 Connecting the 24 V Power Input Cable
- 4.1 Connecting Cables to the SmartLogger
- 5 System Operation
- 6 WebUI Operations
- 6.1 Introduction to WebUI
- 6.2 Device Commissioning
- 6.3 Parameter Settings
- 6.3.1 Setting User Parameters
- 6.3.2 Setting Parameters for Connecting to the Management System
- 6.3.3 Setting RS485 Communications Parameters
- 6.3.4 Setting Parameters for the Slave SmartLogger
- 6.3.5 Setting MBUS Parameters
- 6.3.6 Setting SUN2000 Parameters
- 6.3.7 Setting PID Module Parameters
- 6.3.8 Setting Power Meter Parameters
- 6.3.9 Setting EMI Parameters
- 6.3.10 Setting STS Parameters
- 6.3.11 Setting IEC103 Device Parameters
- 6.3.12 Setting Parameters for a Custom Device
- 6.3.13 Setting IEC104 Device Parameters
- 6.4 Power Grid Scheduling
- 7 Device Maintenance
- 8 FAQ
- 8.1 How Do I Connect the SmartLogger to the SUN2000 App or FusionSolar App?
- 8.2 How Do I Set FTP Parameters?
- 8.3 How Do I Set Email Parameters?
- 8.4 How Do I Change the SSID and Password of the Built-in WLAN?
- 8.5 How Do I Use DI Ports?
- 8.6 How Do I Use DO Ports?
- 8.7 How Do I Use the USB Port?
- 8.8 How Do I Change a Device Name?
- 8.9 How Do I Change the Communications Address?
- 8.10 How Do I Export Inverter Parameters?
- 8.11 How Do I Clear Alarms?
- 8.12 How Do I Enable the AI1 Port to Detect SPD Alarms?
- 8.13 Which Models of Power Meters and EMIs Are Supported by the SmartLogger?
- 8.14 How Do I Check the SIM Card Status?
- 9 Technical Specifications
- A Product User Lists
- B Domain Name List of Management Systems
- C Acronyms and Abbreviations
SmartLogger3000
User Manual
2 Product Overview
Issue 04 (2020-03-11)
Copyright © Huawei Technologies Co., Ltd.
15
Indicators
Indicator
Status
Description
Running
indicator
(RUN)
Green off
The SmartLogger is not powered
on.
Blinking green slowly (on for 1s
and then off for 1s)
The communication with the
management system is normal.
Blinking green fast (on for 0.125s
and then off for 0.125s)
The communication with the
management system is interrupted.
Alarm/Mainten
ance indicator
(ALM)
Alarm status
Red off
No system alarm is raised.
Blinking red
slowly (on for
1s and then off
for 4s)
The system raises a warning
alarm.
Blinking red
fast (on for 0.5s
and then off for
0.5s)
The system raises a minor alarm.
Steady red
The system raises a major alarm.
Maintenance
status
Green off
No local maintenance is in
progress.
Blinking green
slowly (on for
1s and then off
for 1s)
Local maintenance is in progress.
Blinking green
fast (on for
0.125s and then
off for 0.125s)
Local maintenance fails or the
connection to the app is to be set
up.
Steady green
Local maintenance succeeds.
4G indicator
(4G)
Green off
The 4G/3G/2G networking
function is not enabled.
Blinking green slowly (on for 1s
and then off for 1s)
Dial-up through the 4G/3G/2G
network is successful.
Blinking green fast (on for 0.125s
and then off for 0.125s)
The 4G/3G/2G network is not
connected or the communication is
interrupted.
Local maintenance refers to the operations performed by connecting a USB flash drive to the
SmartLogger USB port, such as full data import and export using a USB flash drive, and by
connecting the SmartLogger to the FusionSolar app or SUN2000 app over the built-in WLAN
hotspot.