AP6510DN-AGN Outdoor Wireless LAN Access Point Quick Start Guide HUAWEI TECHNOLOGIES CO., LTD.
Copyright © Huawei Technologies Co., Ltd. 2012. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders.
Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol CAUTION NOTE Description Indicates a potentially hazardous situation, which if not avoided, could result in equipment damage, data loss, performance degradation, or unexpected results. Provides additional information to emphasize or supplement important points of the main text. Change History Changes between document issues are cumulative.
AP6510DN-AGN Quick Start Guide Please download the detailed product documents from "http://support.huawei.com/support/". The detailed path is as follows: Technical Support->Documentation->Access Network -> WLAN ->WLAN -> Product Documentation -> AP6510DN. Technical Support 技术支持 Before performing Installation, confirm that the installation accessories and tools are available.
Installing an AP ● Select an appropriate installation position and leave space above and around the device for cooling air circulation. ● Outdoors APs are used for hotspot coverage and often installed against walls or poles. The pole diameter is 30 to 114 mm. AP6510DN dimensions (unit: mm) without a backplane support 83 306 330 Recommended AP6510DN installation space (unit: mm) ● Installing the AP6510DN against a Wall: 2.
Installing an AP ● Installing the AP6510DN against a vertical pole: 2. Slide the AP that has the connector fastened into the wall1. Determine the AP installation position, slide the hoop mounting bracket. through the hole of the wall-mounting bracket and attach it to the pole, And use the screwdriver to secure screws on the hoop. Field strength 场强示意 ● The procedure for installing the AP6510DN against a horizontal pole is similar to the procedure for installing the AP6510DN against a vertical pole.
Installing Cables ● AP6510DN external cable arrangement drawing Feed line Feed line Feed line Feed line Ground cable Network cable ● Connecting network cables 1. Use a shield straight-through cable. Cut the cable of proper length based on the distance between the AP and the PSE device, peel the insulation on both ends of the network cable, and crimp the wires to RJ45 connectors. 2. Make a network cable onsite according to the following pin assignment.
Installing Cables ● Connecting the feed line 1. The outdoor AP's antenna ports already have 5 KA surge protection capability. Generally, no surge protection devices need to be installed; therefore, the antenna cables are directly connected to the AP's antenna ports. Feed line Waterproof adhesive tape 2. If higher surge protection capability is required, the customer can purchase a surge protection device. When installing the surge protection device, ensure that it is connected to a ground cable.
Installing Cables ● Requirements for Laying Out Cables ● Requirements for laying out power cables 1. The power cable must be separated from ground cables and signal cables. 2. If multiple power cables are installed, you must bind the power cables. 3. The routing of power cables must meet engineering design drawing requirements. 4. If the power cable length is insufficient, replace the power cable. The power cable must be complete and cannot have splices or welding points.
Power-on NOTE 2 连接线缆 Power on the AP6510DN and check the indicator status to determine the system running status. Information Type Description Link Wireless Steady green Off Off The device is being started. Blinking green Off Off The system is working properly. Steady red Off Off The system fails to load the DRAM or system software. Off The system is working properly, but the Ethernet is not connected and radios or all VAPs are disabled.
Logging In to the Router After an AP is powered on, you can log in to the AP using the following methods. 1. Logging In to the AP Using Telnet This section describes how to log in to the AP using Telnet. After logging in to the AP, you can configure the AP using commands. 1. Logging In to the AP Using Telnet This section describes how to log in to the AP using Telnet. After logging in to the AP, you can configure the AP using Commands.
AP Local Configuration WLAN services parameters of an AP are configured on the AC that is connected To the AP, and then delivered to the AP. The following parameters are configured on the AP through Telnet. 1. Configuring the AP Access Mode This section describes how to configure the mode in which an AP goes online. 2. Configuring VLANs on Wired Interfaces of an AP This section describes how to configure VLANs on wired interfaces of an AP. 3.
AP Local Configuration ● Configuring the AP to go online in PPPoE mode 1. Use Telnet to log in to the AP from a PC. login: admin Password: // The default password is admin. ~ # 2. Configure the AP to go online in PPPoE mode. ~ # cli Enterprise AP# configure interface ethernet // Enter the AP interface view. Enter Ethernet configuration commands, one per line. Enterprise AP (if-ethernet) # ip mode pppoe // Set the mode in which the AP goes online.
AP Local Configuration 3. Configuring WDS This section describes how to configure WDS parameters on an AP. ● Introduction to WDS WDS enables multiple AP6510DNs to establish wireless links to connect two or more wired or wireless LANs. WDSenabled AP6510DNs can switch data packets between the LANs. WDS facilitates network deployment, and device installation, and allows flexible networking. ● Configuring WDS Most WDS parameters are configured on the AC. For details, see the AC configuration guides.
Declaration on Hazardous Substances in Electronic Information Products Hazardous Substances Part Pb Hg Cd Cr6+ PBB PBDE Mechanical part O O O O O O Board/circuit module O O O O O O Signal cable O O O O O O Cable connector O O O O O O Power adapter O O O O O O Auxiliary equipment O O O O O O O: Indicates that the concentration of the hazardous substance contained in all the homogeneous materials of this part is below the limit requirement of the SJ/T 11363-200
Warranty Card Thank you for choosing HUAWEI Technologies Co., Ltd-a leading telecom solution provider. To get better services, please read this warranty card carefully, fill in the required information and preserve this card in good condition. Your Name Address/Postal Code Telephone Product Type Product Serial Number Purchase Date Invoice Number Dealer Name Dealer´s Address/Telephone Preserve well. No reissue Dealer´s Seal: Limited Warranty Subject to the exclusions contained below, Huawei Technologies CO.
HUAWEI TECHNOLOGIES CO., LTD. Huawei Industrial Base Bantian, Longgang Shenzhen 518129 People's Republic of China www.huawei.
