B660 Quick Start Note: Figures in this guide are only for your reference. For details about the particular model you have chosen, contact your service provider. Check the information about the product and its accessories when you purchase it. Some accessories are not provided in the product package. If necessary, contact your local dealer to purchase them. This guide briefly describes the device functions.
(Optional) Scenario 2: You can connect a telephone to the device's telephone port to make voice calls. Appearance 1. 2. 3. 4. 5. 6. LAN indicators 7. External antenna port 8. Telephone port 9. Power port 10.
Indicators Indicator Status Wi-Fi/WPS indicator Network status indicator Power indicator / / / LAN indicators Steady on: Wi-Fi turned on. Blinking: WPS connection being set up. Off: Wi-Fi turned off. Blinking red fast: Subscriber Identity Module (SIM) card unavailable (SIM card not installed or malfunctioning, or PIN code not verified). Steady yellow: device registered with the network. Steady green: device connected to the Internet. Off: no signal received.
Computer Hardware and Software Requirements The recommended computer specification is as follows: Central processing unit (CPU): Pentium 500 MHz or faster Random access memory (RAM): ≥ 128 MB Hard drive: 50 MB disk space available Operating system: Windows 2000, Windows XP, Windows Vista, or Windows 7 Liquid crystal display (LCD) resolution: At least 800 x 600 pixels (1024 x 768 pixels is recommended.
Installing the SIM Card 1. Slide the card cover off. 2. Insert the SIM card into the card slot. Ensure that the gold contact area faces down and that the beveled edge of the SIM card aligns with that of the card slot. 3. Slide the card cover back onto the device. Attention: Before removing the SIM card, ensure that the device is powered off and disconnected from the power outlet.
(Optional) Using the Table Stand You can place the device on a flat surface such as a table or a desk, or hang it on a wall. You can also use the table stand on the device to place it upright. To use the table stand, insert its latches into the device's table stand slots, as shown in the following figure. Note: To ensure good signal reception, place the device in a high place or near a window. To prevent interference caused by radio signals, place the device at least 1 meter (3.
(Optional) Installing an External Antenna In areas with poor network coverage, connect an external antenna to the device's external antenna port. Screw the external antenna in fully, as shown in the following figure. Note: Skip this section if you do not need to connect an external antenna to the device. Before using an external antenna, log in to the web management page (http://192.168.1.1) and set antenna mode to external. For details, see the help information on the web management page.
(Optional) Connecting to a Telephone If you want to use the device to make voice calls, connect the device to a telephone, as shown in the following figure. Note: Skip this section if you do not plan to use the device's voice services. Radio signals can interfere with telephone call connection and quality. To eliminate the risk of possible interference, place the telephone at least 1 meter (3.28 feet) away from the device.
Connecting to a Computer Use an Ethernet cable to connect a computer to one of the device's LAN ports, as shown in the following figure. When the connection between the device and the computer is set up, the device's corresponding LAN indicator turns on. Ensure that the Ethernet cable is not longer than 100 meters (328 feet). Connecting to a Power Outlet Connect a compatible power adapter to the device's power port, and then plug the power adapter into a power outlet.
Powering the Device On or Off After connecting to a power outlet, the device will power on automatically. To manually power the device on, press and hold turn on. To power the device off, press and hold until all indicators until all indicators turn off. Setting Up a Wireless Connection Turning the Device's Wi-Fi On By default, the device's Wi-Fi automatically turns on when the device is powered on. To manually turn Wi-Fi on, press and hold steady on.
Method 1: Set up a Wi-Fi connection. is steady on. 1. Ensure that 2. Scan for available wireless network connections using your computer's connection manager application. 3. Connect to the wireless network that has the same service set identification (SSID) as the device. Note: If a security mechanism has been enabled for the wireless network connection, enter the correct network key. The default SSID and Wi-Fi key are printed on the device label.
Accessing the Internet After a connection between your device and the client is set up, you can access the Internet using the modes listed in the following table. Select an appropriate mode according to your data service charging plan. For example, if you are charged according to the length of time you are connected to the Internet, it is recommended that you select manual mode. For details about your data service charging plan, contact your service provider.
Using the Web Management Page You can configure and manage the device settings using the web management page. 1. Launch a web browser, and enter http://192.168.1.1 in the address bar. 2. Enter the password, and log in to the web management page. The default password is admin. Note: To protect your device, only one user can log in to the web management page at a time. To protect your account, change the password promptly. For details, see the help information on the web management page.
Restoring Factory Defaults If you are uncertain of which settings you have configured or changed, you can restore the factory defaults that the device came with, and then reconfigure the device. To restore the factory defaults, Use a sharp-pointed object to press and hold the RESET button until all indicators ( and , , , ) blink. After the factory defaults are restored, the device will restart automatically.
Further Tips If the device does not work properly: See the help information on the web management page. Restart the device. Restore the device to its factory defaults. Contact your service provider.
Copyright © Huawei Technologies Co., Ltd. 2012. All rights reserved. THIS DOCUMENT IS FOR INFORMATION PURPOSES ONLY, AND DOES NOT CONSTITUTE ANY KIND OF WARRANTIES. Please visit www.huaweidevice.com/worldwide/support/hotline for recently updated hotline and email address in your country or region.