Quick Start Guide Model: CP39S
Charging indicator light Mounting arm release button Phone mounting arm Knob Clip release button Wireless charger fixing clip Charging cable DC port Type-C port Proximity sensor 1
1. Install the wireless car charger. a. Plug the standard charging cable into the DC port to connect the wireless charger to the cigarette lighter port. b. Press the clip release button on the back of the wireless charger to open the clip c. Attach the wireless charger onto your car's air vent. After the installation is successful and when the car is started, the wireless charger will initialize and the charging indicator light will flash once. • This product only supports standard 10 V/4 A, 5 V/4.
• Adjust the knob on the back of the wireless charger to secure the wireless charger in place. • To reach the maximum charging power of 27 W, use the standard charging cable and ensure that your phone supports 27 W charging. • Cigarette lighter ports of certain car models still provide power after you switch off your car. If this applies to your car, it is recommended that you disconnect the charging cable from the wireless charger after you switch off your car.
Do not connect all-in-one data cables, such as two-in-one or three-in-one data cables, to the wireless charger. 2. Place your phone (must support Qi wireless charging) near the proximity sensor and the phone mounting arms will open automatically. Place your phone on the wireless charger and the phone mounting arms will automatically attach to your phone. Your phone will then start charging and the charging indicator will show steady on.
the surface of the wireless charger, as shown in the figures below. Ensure that there are no metallic objects between the surface of the wireless charger and your phone. Avoid using a metallic protective case.
flash. 3. Before exiting your car, touch the mounting arm release button on the left side of the wireless charger and remove your phone when the mounting arms open. When the power at the cigarette lighter port or power supply port is cut off, take out your phone directly. If the cigarette lighter port still provides power after you switch off your car, it is recommended that you disconnect the charging cable from the wireless charger. 4.
The sticker stand cannot be repositioned once it has been attached. Please attach it to an appropriate location in your car.
Safety Information
English Safety Information Before you use the device, read the following precautions carefully to ensure optimal product performance and to avoid danger or violation of laws and regulations. • In clinics and hospitals where the use of wireless devices is prohibited, please comply with the regulations and power off your device. • Some wireless devices may interfere with implantable medical devices and other medical equipment, such as pacemakers, cochlear implants, and hearing aids.
• The device and its accessories may contain small components. Keep the device and its accessories out of the reach of children. Otherwise, children may damage the device and its accessories by mistake, or swallow the small components, which may result in hazards such as choking. • Do not drop, squeeze, or pierce the device to avoid short-circuiting and overheating. • Do not place the device directly above or within the reach of vehicle airbags.
Reduction of Hazardous Substances This device and any electrical accessories are compliant with local applicable rules on the restriction of the use of certain hazardous substances in electrical and electronic equipment, such as EU REACH, RoHS and Batteries (where included) regulations, etc. For declarations of conformity about REACH and RoHS, please visit our web site http://consumer.huawei.com/certification.
released by the manufacturer to fix bugs or enhance functions after the product has been released. All software versions released by the manufacturer have been verified and are still compliant with the related rules. All RF parameters (for example, frequency range and output power) are not accessible to the user, and cannot be changed by the user. For the most recent information about accessories and software, please see the DoC (Declaration of Conformity) at http://consumer.huawei.com/certification.
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Any changes or modifications to this device not expressly approved by Huawei Technologies Co., Ltd. for compliance could void the user's authority to operate the equipment. IC Statement This device complies with CAN ICES-1/NMB-1. This device complies with Industry Canada licence-exempt RSS standard(s).
Legal statement Copyright © Huawei Technologies Co., Ltd. 2019. All rights reserved. This document is for reference only. Nothing in this guide constitutes a warranty of any kind, express or implied. Please visit http://consumer.huawei.com/en/support/index.htm for recent updated hotline and email address in your country or region. The "Qi" symbol is a trademark of the Wireless Power Consortium. Privacy Protection To understand how we protect your personal information, please visit http://consumer.huawei.