Thank you for choosing HUAWEI Mobile WiFi Supported functions and actual appearance depend on the specific models you purchased. The illustrations are provided for your reference only. For details about the model you selected, consult your service provider. This guide briefly describes the functions of the Mobile WiFi. For more details, see help on the web management page. Copyright © Huawei Technologies Co., Ltd. 2012. All rights reserved.
Getting to Know HUAWEI Mobile WiFi Connection Scenario A Wi-Fi device can be connected to the Internet through the Mobile WiFi. The actual connection procedure depends on the operating system of the Wi-Fi device. The connection scenario illustrated here is for your reference.
Appearance No. 1 2 3 4 5 6 7 8 Item Screen WPS button Press it twice in one second to view the SSID and wireless network key sequentially. Press and hold it until a WPS activation animation is displayed to enable the WPS function.
Screen No.
Note: Wi-Fi: Wireless Fidelity WPS: Wi-Fi Protected Setup Traffic statistics are for your reference only. To obtain the actual traffic data, contact your service provider. SSID and Wireless Network Key To connect a Wi-Fi device to your Mobile WiFi, an SSID and a wireless network key are required. The default SSID and wireless network key can be found in the gift box. In addition, press the button twice in one second to view the current SSID and wireless network key sequentially on the screen.
Before You Start Installing the SIM Card Caution: Do not use any SIM card that is not standard or is incompatible with the Mobile WiFi. Otherwise, the Mobile WiFi may be damaged. Insert the SIM card in the card slot. Be sure that the SIM card is facing in the right direction, as shown in the following figure, and then slide the SIM card into the slot.
Installing the microSD Card Insert the microSD card into the Mobile WiFi, as shown in the following figure. Note: The microSD card is an optional accessory. If a microSD card did not come with your Mobile WiFi, you may purchase one yourself. To remove the microSD or SIM card, press in the card gently. The microSD or SIM card will pop out for removal. Do not remove the microSD or SIM card when the card is in use.
Charging the Battery Charge your Mobile WiFi the first time you use it or if it has not been used for a long time. Method 1: Using the charger Caution: Only use chargers compatible with the Mobile WiFi and provided by a designated manufacturer (HW-050200E3W). Use of an incompatible charger or one from an unknown manufacturer may cause the Mobile WiFi to malfunction, fail, or could even cause a fire. Such use voids all warranties, whether expressed or implied, on the product.
Method 2: Connecting to a PC for charging Connect the Mobile WiFi to a PC using a compatible data cable.
Accessing the Internet via Wi-Fi Connection By default, management parameters are preset on the Mobile WiFi according to the requirements of the service provider. Follow the steps below to quickly access the Internet. For the details about how to set management parameters, see help on the web management page. Step1: Power on the Mobile WiFi Press and hold until the screen lights up. The Mobile WiFi is powered on. Note: Press and hold Mobile WiFi.
Step2: Establish a Wi-Fi Connection (Take a computer with Windows XP operating system as an example) 1. Make sure that the Wi-Fi is enabled. 2. Select Start > Control Panel > Network Connections > Wireless Network Connection. Note: To set up a Wi-Fi connection, the PC must have a wireless network adapter installed. If Wireless Network Connection is displayed, a wireless network adapter is available. Otherwise, check to make sure you have a wireless network adapter installed. 3.
Step3: Access the Internet After you establish a Wi-Fi connection successfully, you can access the Internet using the following modes. Caution: Please select a proper Internet connection mode based on your service expense. For example, if you are subscribed to the time-based network service, you are recommended to select Manual mode. For details about the service expense, consult your service provider.
Note: Launch the web management page to select the mode for accessing the Internet. You can choose whether to enable the Mobile WiFi to connect to the Internet automatically even while you are roaming. If this function is disabled, the Mobile WiFi automatically disconnects from the Internet while you are roaming. To access the Internet, set up a connection manually. Accessing the Web Management Page 1. Make sure that the connection between the Mobile WiFi and the client is a proper one. 2.
Daily Use Power Saving Mode If no operation is performed on the Mobile WiFi within a preset period, the screen turns off. Press any key to light up the screen. When the Mobile WiFi is powered on, choose whether to enable the Mobile WiFi to turn off Wi-Fi automatically. If this function is enabled and no Wi-Fi devices access the Mobile WiFi for a preset period, the Mobile WiFi turns off Wi-Fi automatically. You can press the button to turn on Wi-Fi again.
Establishing a WPS Connection If a Wi-Fi client connected to the Mobile WiFi supports the WPS function, a wireless network key will be automatically generated without manual input. To establish a WPS connection, perform the following steps: 1. Power on the Mobile WiFi. 2. Start the client. 3. Enable the WPS function of the Mobile WiFi. Note: After Wi-Fi is enabled, press and hold until a WPS activation animation is displayed on the screen to enable the WPS function of the Mobile WiFi. 4.
Restoring Factory Defaults If you forget the changes you have made to some parameters, you may restore factory defaults and reconfigure the Mobile WiFi. To restore the factory defaults, press and hold the RESET button until the screen turns off. All factory default settings are successfully restored. Note: Restoring factory defaults deletes all personal configuration settings and restores all web-based management settings and parameters to their default values.
Example 1: Wi-Fi Connection to Game Machine (Sony PSP) 1. 2. 3. 4. 5. 6. Turn on the PSP WLAN switch. Select Settings > Network Settings. Select Infrastructure Mode to connect to your local Wi-Fi access point. Select New Connection to specify an easy to remember connection name. Select Scan to detect all networks within range. The access point list is displayed. Select a network indicated by the SSID of the Mobile WiFi.
Note: Press the button twice in one second to view the current SSID and wireless network key sequentially on the screen. 7. Press the ► button of your game machine to continue, and then press the X button to save the settings. 8. Select Test Connection to check the connection. 9. Go to Internet Browser.
Example 2: Wi-Fi Connection to a Smart Phone (iPhone) 1. Select Settings > Wi-Fi, and then turn on Wi-Fi. 2. Automatically detect the networks in range and display the access point list. 3. Select a network indicated by the SSID of the Mobile WiFi. 4. If necessary, enter a password and tap Join. (Networks requiring a password appear with a lock icon.) Note: Some Wi-Fi clients such as iTouch, PS3 and NDSi can also access the Internet via the Mobile WiFi.
Tips If the Mobile WiFi is placed in an environment with poor ventilation, it may overheat after extended use. When the Mobile WiFi overheats, it will switch off and disconnect from the network automatically to protect itself. If this happens, place the Mobile WiFi in a well-ventilated location, then restart the Mobile WiFi. If you are experiencing difficulties using the Mobile WiFi, try the following: See help on the web management page. Restart the Mobile WiFi. Restore the factory defaults.
