S2700&S3700 Series Ethernet Switches V100R006C03 Quick Start Issue 02 Date 2012-10-27 HUAWEI TECHNOLOGIES CO., LTD.
Copyright © Huawei Technologies Co., Ltd. 2012. All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademarks and Permissions and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders.
S2700&S3700 Series Ethernet Switches Quick Start About This Document About This Document Intended Audience This document describes how to verify basic functions of the S2700, S2752, S3700 during the deployment to ensure stable and reliable running of the S2700, S2752, S3700 on the network.
S2700&S3700 Series Ethernet Switches Quick Start About This Document Command Conventions The command conventions that may be found in this document are defined as follows. Convention Description Boldface The keywords of a command line are in boldface. Italic Command arguments are in italics. [] Items (keywords or arguments) in brackets [ ] are optional. { x | y | ... } Optional items are grouped in braces and separated by vertical bars. One item is selected. [ x | y | ...
S2700&S3700 Series Ethernet Switches Quick Start Contents Contents About This Document.....................................................................................................................ii 1 Overview.........................................................................................................................................1 2 Product Hardware Introduction..................................................................................................2 2.1 S2700 Introduction..
S2700&S3700 Series Ethernet Switches Quick Start 1 Overview 1 Overview This section provides an overview of quick start. This document helps you quickly learn how to use the S2700&S3700. Figure 1-1 shows the quick start contents.
S2700&S3700 Series Ethernet Switches Quick Start 2 2 Product Hardware Introduction Product Hardware Introduction About This Chapter This section describes models and indicators of low-end switches. 2.1 S2700 Introduction This section describes S2700 models. 2.2 S3700 Introduction This section describes S3700 models. 2.3 S2700 Indicator Description 2.4 S3700 Indicator Description This section describes the indicators on the S3700 front panel.
S2700&S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction 2.1 S2700 Introduction This section describes S2700 models. Device Models To meet diverse customer requirements, the S2700 provides a variety of models. Table 2-1 lists these device models. You can select a device model as required.
S2700&S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction Naming Rules The following are the naming rules of the S2700-26TP-PWR-EI, S2710-52P-SI-AC, S2700-52P-EI, and S2700-9TP-SI. Figure 2-1 Naming rules S2700-26TP-PWR-EI AB C D E F G S2710-52P-SI-AC AB C D E G H S2700-52P-EI-AC DE G H S2700-9TP-SI DE G Ide ntifi er Description A Switch. B Product series. "27" indicates the S2700 series. C Product subseries. D Maximum number of interfaces.
S2700&S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction Ide ntifi er Description F The S2700 supports Power over Ethernet (PoE). NOTE If this letter is not displayed, PoE is not supported. G Software version type: l EI: enhanced version, supporting enhanced features. l SI: standard version, supporting basic features. H Powering mode: l AC: alternating current power l DC: direct current power 2.2 S3700 Introduction This section describes S3700 models.
S2700&S3700 Series Ethernet Switches Quick Start Produ ct Series 2 Product Hardware Introduction Model Maximum Number of Interfaces S3700-52P-SI-AC 52 S3700-52P-EI-AC S3700-52P-EI-DC There are forty-eight 10/100BASE-T Ethernet interfaces, two 100/1000BASE-X Ethernet optical interfaces, and two GE SFP interfaces.
S2700&S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction Figure 2-2 Naming rules S3700-28TP-PWR-EI A B CD E F S3700-52P-EI-24S-DC CD F G H S3700-28TP-SI-AC CD F H S3700-28TP-EI-MC-AC C D F I H Ide ntifi er Description A Switch. B Product series. "37" indicates the S3700 series. C Maximum number of interfaces. NOTE The number of interfaces on an S3700 can be 28, or 52, depending on the device model. D Uplink interface type: l P: A device has optical interfaces.
S2700&S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction Ide ntifi er Description F Software version type: l EI: enhanced version, supporting enhanced features l SI: standard version, supporting basic features G Downlink interface type. The value 24S indicates that 24 downlink interfaces of the S3700-52P-EI-24S are optical interfaces. NOTE If this letter is not displayed, all downlink interfaces are electrical interfaces.
S2700&S3700 Series Ethernet Switches Quick Start No. 3 Indicator Port indicator 2 Product Hardware Introduction Identifier LNK/ACT 4 Status Description Blinking green The system is operating properly. Off The interface is not connected or has been shut down. Green The interface is connected. Blinking green The interface is sending or receiving data. NOTE SYS on the front panel of an S2710-52P-SI-AC indicates the system status indicator.
S2700&S3700 Series Ethernet Switches Quick Start No. Indicator 2 Product Hardware Introduction Identifier Status Description Red l Two power supply units are installed properly, but not switched on. l The power supply units are switched off. l The card power and PoE power are abnormal. 2 Power indicator PWR2 Orange If a single power supply unit is installed, the PoE power is out of range. If two power supply units are installed, the card power or PoE power is out of range.
S2700&S3700 Series Ethernet Switches Quick Start No. 4 Indicator Mode indicator 2 Product Hardware Introduction Identifier - Status Description Blinking green The system is operating properly. Red After registering, the system does not operate properly, or a power alarm, fan alarm, or temperature alarm is generated. Off The service interface indicator is in the default mode (STAT). Green The service interface indicator indicates the interface speed.
S2700&S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction Display Mode Status Description Speed Off The interface is not connected or has been shut down. Green The interface speed is 10/100 Mbit/s. Blinking green The interface speed is 1000 Mbit/ s. Off The interface does not provide remote power. Green The interface is providing remote power. Blinking green The power of the powered device (PD) exceeds the power supply capability of the port or exceeds the threshold.
S2700&S3700 Series Ethernet Switches Quick Start No. Indicator 2 Product Hardware Introduction Identifier Status Description Red l Two power supply units are installed properly, but not switched on. l The power supply units are switched off. l The card power and PoE power are abnormal. 2 Power indicator PWR2 Orange If a single power supply unit is installed, the PoE power is out of range. If two power supply units are installed, the card power or PoE power is out of range.
S2700&S3700 Series Ethernet Switches Quick Start No. Indicator Identifier Status Description 3 System status indicator SYS Off The system is not operating. Green The system is not operating properly or is starting. Orange The system is performing selfcheck during startup. Blinking green The system is operating properly. Red After registering, the system does not operate properly, or a power alarm, fan alarm, or temperature alarm is generated.
S2700&S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction As shown in Figure 2-5, the button marked "5" is the mode switching button. On an S2700, you can press the mode switching button to switch the display modes of interface indicators. The status of the mode indicator represents the display mode of the related interface indicator. For example, the mode indicator of S2710-52P-PWR-SI is off and the interface indicators are in STAT state by default.
S2700&S3700 Series Ethernet Switches Quick Start Display Mode 2 Product Hardware Introduction Status Description Green The device is a not a command switch: l If the indicator of an interface is always on, the number of this interface is the stack ID of the device. l If the first nine interface indicators of the device are always on, the stack ID of the device is 0.
S2700&S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction No. Indicator Identifier Status Description 2 System status indicator RUN Off The system is not operating. Green The system is not operating properly or is starting. Blinking green The system is operating properly. Off The interface is not connected or has been shut down. Green The interface is connected. Blinking green The interface is sending or receiving data.
S2700&S3700 Series Ethernet Switches Quick Start No. Indicator 2 Product Hardware Introduction Identifier Status Description Red l Two power supply units are installed properly, but not switched on. l The power supply units are switched off. l The card power and PoE power are abnormal. 2 Power indicator PWR2 Orange If a single power supply unit is installed, the PoE power is out of range. If two power supply units are installed, the card power or PoE power is out of range.
S2700&S3700 Series Ethernet Switches Quick Start No. Indicator Identifier Status Description 3 System status indicator SYS Off The system is not operating. Green The system is not operating properly or is starting. Orange The system is performing selfcheck during startup. Blinking green The system is operating properly. Red After registering, the system does not operate properly, or a power alarm, fan alarm, or temperature alarm is generated.
S2700&S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction As shown in Figure 2-7, the button marked "5" is the mode switching button. On an S3700, you can press the mode switching button to switch the display modes of interface indicators. The status of a mode indicator represents the display mode of the related interface indicator. For example, the mode indicator of S3700-28TP-PWR-EI is off and the interface indicators are in STAT state by default.
S2700&S3700 Series Ethernet Switches Quick Start Display Mode 2 Product Hardware Introduction Status Description Green The device is a not a command switch: l If the indicator of an interface is always on, the number of this interface is the stack ID of the device. l If the first nine interface indicators of the device are always on, the stack ID of the device is 0.
S2700&S3700 Series Ethernet Switches Quick Start 3 Device Installation 3 Device Installation This section describes how to install the S2700&S3700. For details on device installation, see the S2700&3700&5700&6700 Quick Installation Guide. NOTE You can obtain the paper documentation of the Quick Installation Guide from delivered accessories. To obtain the electronic documentation of the Quick Installation Guide, see Where to Obtain Documentation.
S2700&S3700 Series Ethernet Switches Quick Start 4 Powering on the Device 4 Powering on the Device About This Chapter This section describes the check items and the procedure for powering on and powering off the device. 4.1 Checking Before Power-on After hardware installation is complete, you need to check the device installation and cable installation. 4.2 Powering on the Device 4.3 Checking After Power-on Issue 02 (2012-10-27) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co.
S2700&S3700 Series Ethernet Switches Quick Start 4 Powering on the Device 4.1 Checking Before Power-on After hardware installation is complete, you need to check the device installation and cable installation. NOTE Before power-on, you need to check the device cabinet, cables, connectors, sockets, labels, and on-site environment. Device Installation Checklist CAUTION Before power-on, all the power distribution cabinets and power distribution frames must be off.
S2700&S3700 Series Ethernet Switches Quick Start 4 Powering on the Device No. Item Method 3 The installation holes on the support and the expansion bolts adapt to each other to ensure insulation between the support and the ground and between the floor bracket and the guide rail. Use the multimeter to measure the resistance between the bolt and the ground bolt of the rack. The resistance must be more than five mega ohms. 4 The surfaces of the cabinets in the same row should be on the same plane.
S2700&S3700 Series Ethernet Switches Quick Start 4 Powering on the Device No. Item Method 7 The card is installed and removed easily. The screws on the panel should be appropriately tightened and easily disassembled. The spring wire is intact. - 8 The cabinet surface must be tidy and clean; the components of the cabinet cannot be distorted; all identifiers are correct, clear, and complete. - 9 The cabinet is kept clean and there are no excessive binding straps and other articles in the cabinet.
S2700&S3700 Series Ethernet Switches Quick Start 4 Powering on the Device No. Item Method 2 The power cables and ground cables are connected safely. The spring washer of the ground cable terminal is on the flat washer. - 3 The lugs of the power cables and ground cables are soldered or crimped tightly. - 4 The power cables and ground cables are not crossed and are separated from other cables. 5 The redundant part of the power cables and ground cables should be cut. The cables cannot be circled.
S2700&S3700 Series Ethernet Switches Quick Start 4 Powering on the Device Table 4-4 Signal cable checklist No. Item Method 1 All the signal cables to be deployed pass the continuity check. - 2 No signal cable is placed on the heat dissipation holes of the cabinet. - 3 The bent part of a signal cable cannot be too tight. 4 The cables in the cabinet cannot be crossed and the cables outside the cabinet are bound.
S2700&S3700 Series Ethernet Switches Quick Start 5 Logging in to the Device 5 Logging in to the Device About This Chapter This section describes how to log in to the device. 5.1 Logging In to the Switch Through the Console Interface 5.2 Example for Configuring to Manage the Switch Through Telnet 5.3 Logging In to the Web System Client Before configuring the switch, you must log in to the Web system client. Issue 02 (2012-10-27) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co.
S2700&S3700 Series Ethernet Switches Quick Start 5 Logging in to the Device 5.1 Logging In to the Switch Through the Console Interface Context When establishing the configuration environment through the console interface, you can log in to theS2700&3700 through the HyperTerminal in Windows. Procedure Step 1 Start the HyperTerminal. Choose Start > All Program > Accessories > Communications > HyperTerminal to start the HyperTerminal in Windows XP. Step 2 Set up a connection. See Figure 5-1.
S2700&S3700 Series Ethernet Switches Quick Start 5 Logging in to the Device Figure 5-2 Configuring the interface for connection Step 4 Set communication parameters. When the COM1 Properties dialog box is displayed as shown in Figure 5-3, specify the parameters listed in Table 5-1. NOTE In other Windows operating systems, bits per second may be described as baud rate and data stream control may be described as traffic control.
S2700&S3700 Series Ethernet Switches Quick Start 5 Logging in to the Device Figure 5-3 Specifying parameters Table 5-1 Parameters Parameter Value Bit per second (baud rate) 9600 Data bit 8 Parity check None Stop bit 1 Flow control (traffic control) None Step 5 After the HyperTerminal starts, choose FileAttributes to display the COMM1 Properties dialog box, as shown in Figure 5-4. On the Setting tab, select VT100 in the Emulation dropdown list box. Click OK to complete the setting.
S2700&S3700 Series Ethernet Switches Quick Start 5 Logging in to the Device Figure 5-4 Selecting the terminal type ----End Follow-up Procedure After the preceding configurations are complete, press Enter. If the prompt is displayed on the screen, it indicates that the Command Line Interface (CLI) is displayed. In this case, you can enter commands to configure or manage the S2700&3700. For details on configuration procedures, see the following sections. 5.
S2700&S3700 Series Ethernet Switches Quick Start 5 Logging in to the Device Figure 5-5 Networking diagram of managing SwitchA through Telnet administrator Ethernet SwitchB GE 0/0/1 RS-232 serial port Console port Console cable PC GE 0/0/1 SwitchA Configuration Roadmap The configuration roadmap is as follows: l Log in to SwitchA through the console interface. l Set the device name. l Configure a management VLAN.
S2700&S3700 Series Ethernet Switches Quick Start 4. 5 Logging in to the Device On SwitchA, set the type of the interface that connects SwitchA and SwitchB to trunk. Add the interface to the management VLAN in trunk mode. [SwitchA] interface Gigabitethernet 0/0/1 [SwitchA-GigabitEthernet0/0/1] port link-type trunk [SwitchA-GigabitEthernet0/0/1] port trunk allow-pass vlan 1 [SwitchA-GigabitEthernet0/0/1] quit 5. Configure the management IP address of SwitchA.
S2700&S3700 Series Ethernet Switches Quick Start 5 Logging in to the Device # interface Vlanif1 ip address 10.10.10.10 255.255.255.
S2700&S3700 Series Ethernet Switches Quick Start 5 Logging in to the Device Figure 5-6 Login Step 3 Enter values in User Name, Password, and Verify Code. l The local switch provides a default account. The user name and password of the account are admin. l To create, change, or delete user names and passwords, choose Security > AAA > User Management. l Users of levels 0, 1, and 2 has only visit-level rights,and can view only the Ping and Tracert pages after logging in to the client.
S2700&S3700 Series Ethernet Switches Quick Start 6 Service Deployment 6 Service Deployment This section describes service deployment. For details on service deployment, see the corresponding configuration guides. Issue 02 (2012-10-27) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
S2700&S3700 Series Ethernet Switches Quick Start 7 Obtaining Documentation 7 Obtaining Documentation You can obtain product documentation, online help, and release documents in various ways. Product Documents Table 7-1 shows how to obtain product documents. Table 7-1 Obtaining product documents Phase How to Obtain Documentation Installation HedEx Library Single Electronic Document l From the electronic documentation delivered with the equipment l From http:// enterprise.huawei.
S2700&S3700 Series Ethernet Switches Quick Start l 7 Obtaining Documentation Pressing F1 on any interface of the NMS Release Documents Release documents are released with the software package. You can apply to Huawei technical support personnel for the documents. Issue 02 (2012-10-27) Huawei Proprietary and Confidential Copyright © Huawei Technologies Co., Ltd.
