Installation & Assembly

ManualsBrandsHubbardton Forge ManualsOutdoor Hanging LightsHenry 1 -Light Outdoor Pendant

Installation Instructions A370

Quill Pendant 135001 Page 1 of 3

Hand-Forged, Vermont-Made Lighting and Accessories

154 Route 30 South, Castleton, Vermont 05735 30901 -

(Figure 1)

To Install the Canopy & Vertical Installation (Figure 1&2)

Component Parts

A Crossbar

B Ground Screw

C Cupped Washer

D Canopy

E #8 Screws

F Fixture

G Canopy Gripper

H Supply/Support Cable

K Canopy Plate

L Screws w/Lock Washers

Caution: Be sure power is off at the main breaker box prior to installation

1. Carefully unpack the fixture from the carton.

2. Crossbar (A) is shipped installed. Remove screws (E) from canopy (D) and save for later use. Remove crossbar

(A).

3. Using two machine screws (not provided), fasten the crossbar (A) to the electric box. (Figure 1)

Note: A new electric box comes with screws. When

replacing a fixture, retain the existing screws for

use with the new fixture.

4. Height of fixture can be set before attaching the

fixture to the ceiling. Remove screws w/lock

washers (L) and canopy plate (K) from canopy (D).

(Figure 2)

Note: Fixture is shipped at max height.

5. Loosen safety nut on canopy gripper (G) by

twisting counter clockwise. Push supply/support

cable (H) into canopy gripper (G) until desired

height is reached.

6. Retighten safety nut on canopy gripper (G).

7. Coil supply/support cable (H) in canopy (D) and

place canopy plate (K) in canopy (D). Install

screws w/lock washers (L) to secure plate.

Caution: Be sure not to pinch the supply/support

cable in between the canopy (D) and the canopy

plate (K).

(continued)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

(Figure 1)

Summary of content (3 pages)

PAGE 1
A370 Installation Instructions Quill Pendant 135001 Page 1 of 3 CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.* Caution: Do not exceed maximum wattage noted on fixture.
PAGE 2
A370 Installation Instructions Quill Pendant 135001 Page 2 of 3 8. Using suitable wire connectors (not provided) connect fixture wires to supply wires (white to white, black to black). Run a pigtail lead from crossbar ground screw (B) to the junction box and connect all ground wires (bare copper or green to bare copper or green). (Figure 1) (Figure 2) Caution: Make sure wire connectors are twisted on securely, and no bare wire is exposed. 9. Raise canopy (D) close to ceiling.
PAGE 3
A370 Installation Instructions Quill Pendant 135001 Page 3 of 3 (Figure 4) If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased this product. We hope you enjoy your fixture! * Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.