Installation Instruction

ManualsBrandsHubbardton Forge ManualsCeiling LightsBento Unique / Statement Geometric LED Pendant

Assembly & Installation Instructions A365

Bento LED Pendant 138650D Page 1 of 6

Hand-Forged, Vermont-Made Lighting and Accessories

P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735 30852

To Install to Ceiling (Figures 1 thru 5)

Component Part

A Ceiling Bracket

B Lag Screw (4)

C Canopy

D Canopy Support Cable

E #8 Screw

F Support/supply Cable (3)

G Cable Gripper (3)

H Flat Head Screws (2)

I Canopy Nipple

J Canopy Cover

K Cap

L Insulating Barrier

Caution: Be sure power is off at the main breaker box prior to

installation.

1. Carefully unpack the fixture from the carton. Put the ceiling

bracket (A) and canopy (C) together, making sure the canopy

mounting holes match up with the ceiling bracket threaded

standoffs. Orient them to achieve desired wire location.

Note: Flat head screws (H) will need to be removed from

ceiling bracket (A) prior to installation of the canopy (C).

The screws are shipped installed. Remove screws and

retain for step 13.

2. Place insulating barrier (L) between ceiling bracket

and ceiling and align holes.

3. Using the supplied lag screws or other fasteners

suitable for the mounting surface (B) attach ceiling

bracket (A) to a structural member in the ceiling,

centering the crossbar over the outlet box (Figure 1).

There should be fasteners in at least two of the four

holes provided. Lag screws have been supplied with

your fixture; however, different materials and/or

construction methods may require different fasteners.

If in doubt, contact a qualified electrician. Do not

attach crossbar directly to outlet box.

4. Attach canopy support cable (D) to mounting bracket

using a #8 screw (E). Temporarily suspend canopy

using cable (Figure 2). #8 screw (E) ships installed, it

will need to be removed prior to installation of the

support cable (D).

Caution: The cable is intended to temporarily suspend the

canopy to help with fixture installation.

(continued)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

Note: Support Cable also acts as Low Voltage Supply Cable.

(Figure 1)

(Figure 2)

Summary of content (6 pages)

PAGE 1
Assembly & Installation Instructions A365 Bento LED Pendant 138650D Page 1 of 6 CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.* Caution: Do not exceed maximum wattage noted on fixture.
PAGE 2
Assembly & Installation Instructions A365 Bento LED Pendant 138650D Page 2 of 6 5. Loosen cable gripper locks before trying to install cables. (Figure 3). Note: Support cable (F) will not be able to pass through the cable gripper (G) unless the locks are loose. 6. Raise fixture and push support cables (F) through the canopy (C) and into the cable grippers (G) until desired fixture height is accomplished and level. Once desired height is accomplished and product is level, tighten cable gripper locks.
PAGE 3
Assembly & Installation Instructions A365 Bento LED Pendant 138650D Page 3 of 6 15. Thread cap (K) on to canopy nipple (I). Tighten against canopy cover (J) until snug. 16. Refer to instructions following to assemble and install shade. Assemble Shade (Figure 6) Component Parts M Shade (6) N Plastic Rivets. (Figure 5) 1. Remove shade from plastic bag. 2. Locate ‘Flap End’ and “Open End” of shade. (Figure 6) 3. Secure “Flap End” of shade by pressing Plastic Rivets into holes in shade.
PAGE 4
Assembly & Installation Instructions A365 Bento LED Pendant 138650D Page 4 of 6 (Figure 7) (Figure 8) (Figure 9) Hand-Forged, Vermont-Made Lighting and Accessories P.O.
PAGE 5
Assembly & Installation Instructions A365 Bento LED Pendant 138650D Page 5 of 6 (Figure 10) (Figure 11) (Figure 12) Hand-Forged, Vermont-Made Lighting and Accessories P.O.
PAGE 6
Assembly & Installation Instructions A365 Bento LED Pendant 138650D Page 6 of 6 Install Shade (Figure 13) Component Parts S N O Shade Assy Thumb Screw (6) Shade Bracket (6) 1. Remove Thumb screws (N) from fixture and set aside. (Figure 13) 2. Loosely install one Shade Bracket (O) (Figure 14). 3. Slip Shade assembly (S) in between fixed bracket and Shade Bracket (O) 4. Rotate Shade assembly into place and install second Shade bracket (O) opposite from the loosely installed Shade Bracket (Figure 14) 5.