Installation Instructions

ManualsBrandsHubbell Control Solutions ManualsElectronicsWireless Lighting Control

3511B 06152020

72-00655

™

PRELIMINARY

NX Wireless Rocker Wall Station

INSTALLATION INSTRUCTIONS

IMPORTANT SAFEGUARDS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

PRECAUTIONS

Read and understand all instructions before beginning installation.

CAUTION: FOR USE WITH CLASS 2, LOW VOLTAGE SYSTEMS ONLY. DO NOT USE IN HIGH VOLTAGE APPLICATIONS.

NOTICE: For installation by a licensed electrician in accordance with National and/or Local Electrical Codes and the following instructions.

Conrm device ratings are suitable for application prior to installation. Use of this device in applications beyond its specied ratings other than its

intended use may cause an unsafe condition and will void manufacturer’s warranty.

Use only approved materials and components (i.e. wire nuts, electrical box, etc.) as appropriate for installation.

NOTICE: DO NOT INSTALL IF PRODUCT APPEARS TO BE DAMAGED.

NOTICE: Do not use outdoors.

NOTICE: Do not use this equipment for other than its intended use.

NOTICE: The NX Wireless Wall Station uses 1 CR2032 coin cell battery ONLY. Do not use rechargeable battery. Using an improper battery may damage

the NX Wireless Wall Station. Please dispose of this battery at a recycling facility. Contact your local waste disposal provider to nd a recycling center

location nearest you.

CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to instructions.

REGULATORY INFORMATION

• Contains Transmitter Module FCC ID: YH9NXSWWRS IC:9044A-NXSWWRS

1. This device complies with FCC part 15 Rules. Operation is subject to the following two conditions: This device may not cause harmful inference.

2. This device must accept any interference received, including interference that may cause undesired operation.

• FCC Interference Statement (Part 15.105(b)): This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment o and on, the user is encouraged to try to correct the interference by one of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver

3. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

• FCC Part 15 Clause 15.21: Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority

to operate the equipment.

• ISED RSS-Gen Notice

This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:

1. The device may not cause interference; and

2. This device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux

deux conditions suivantes:

1. l’appareil ne doit pas produire de brouillage;

2. l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

SAVE THESE INSTRUCTIONS AND PROVIDE TO OWNER AFTER INSTALLATION IS COMPLETED

701 Millennium Blvd. | Greenville, SC 29607 | (864) 678-1000 | www.hubbellcontrolsolutions.com

identiers are trademarks ™ or registered trademarks ® of Hubbell Lighting, Inc. or their respective owners. Use of them does not necessarily imply any

aliation with or endorsement by such respective owners.

Summary of content (5 pages)

PAGE 1
™ NX Wireless Rocker Wall Station INSTALLATION INSTRUCTIONS Y IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS PRECAUTIONS Read and understand all instructions before beginning installation. AR CAUTION: FOR USE WITH CLASS 2, LOW VOLTAGE SYSTEMS ONLY. DO NOT USE IN HIGH VOLTAGE APPLICATIONS. NOTICE: For installation by a licensed electrician in accordance with National and/or Local Electrical Codes and the following instructions.
PAGE 2
™ DESCRIPTION Y Hubbell Control Solutions’ NX Wireless Wall Station provides wireless manual control of the NX System. The NX Wireless Wall Station provides simple ON, RAISE, LOWER, and OFF functionality for NX Devices and NX Enabled Luminaires. The NX Wireless Wall Station can be configured via the controlHUBB mobile application and can be utilized in either stand alone or networked applications with other NX Room Control or NX Network devices.
PAGE 3
™ Y 4. Install the magnetic NX Wall Station faceplate, or a decora style faceplate of your choice. If a faceplate other than the one provided requires screws, use the shorter 6mm screws provided to anchor the faceplate to the NX Wall Station. AR ctly onto a wall, first thoroughly pyl alcohol to remove any dirt or dust. e Command™ Strip and align the he back of the Instant Switch. tic backing and ensure that the firmly to the wall.
PAGE 4
™ Y t you are working on at your AR onto the access door of the FIGURE 4: GROUND WIRE INSTALLATION 19 3. Connect the ground wire attached to the NX Wall Station to the ground wired located in the gang box. IN 4. If you choose this method of installation, the 3M Command™ Strip is on not required. If direct mounting to a gang box use the longer 22mm screws provided to mount the device directly to the gang box (See Figure 5). 5.
PAGE 5
™ 4. Remove the battery by inserting your finger in the notch and pulling it toward you as seen in Figure 6. 5. When replacing the battery, be sure to install with the positive (+) side facing out so it is visible. Y 3. After the module assembly has been removed turn the device over to reveal the battery located on the back. 6. To replace the module line up the tabs on the bottom of the module assembly with the arrows on the bottom of the mounting plate as seen in Figure 7.