Spec Sheet
ManualsBrandsHubbell ManualsCommercial Dish Washing EquipmentBooster Heater Electric, 13.5 kW with 16-Gallon Storage Capacity, ASME Stamped Stainless Steel Tank with CFC/HCFC Free Closed Cell Foam insulation, Electronic Display Controller with Low Water Cut-Off and Leak Detection, Stainless Steel Exterior, Pressure
Table Of Contents
J6 and J16 Wiring Chart (cont.)
kW Volt Ph
Unit
Amp
Draw
Branch
Amp
Draw
Phase-
Phase
Resistance
(Ohms)
Min.
Feed
Breaker
or Fuse
Size
Internal
Power
Wire
Size
Element
Jumper
Wire
Size
Copper
Power Feed
Wire Size
Conduit
Size
Diagram
208 1 195.0 65.0 1.1 245 8 10 250 2" 6A
208 3 112.6 56.3 2.1 145 8 10 1/0 1¼" 12(NCB)
240 1 168.8 56.3 1.4 215 8 10 250 1½" 6A
240 3 97.4 48.7 2.8 125 10 12 1 1" 12(NCB)
380 3 60.8 60.8 7.1 80 8 10 3 1" 13(WT)
480 3 48.7 48.7 11.4 65 8 10 4 ¾" 13(WT)
600 3 36.2 36.2 19.1 50 10 12 8 ¾" 15
208 3 119.1 59.5 1.9 150 8 10 2/0 1¼" 12(NCB)
240 1 187.5 62.5 1.3 235 8 10 250 2" 6A
240 3 108.3 54.1 2.6 140 8 10 1/0 1¼" 12(NCB)
380 3 68.6 34.3 6.4 90 12 12 2 1" 12(WT)
480 3 54.1 54.1 10.2 70 8 10 4 ¾" 13(WT)
600 3 42.2 42.2 16.4 55 10 12 6 ¾" 15
208 3 149.9 74.9 1.6 190 6 8 3/0 1½" 12
240 3 129.9 65.0 2.1 165 8 10 2/0 1½" 12
380 3 80.0 40.0 5.3 100 10 12 1 1" 12(WT)
480 3 65.0 65.0 8.5 85 8 10 4 1" 13(WT)
600 3 54.3 54.3 12.8 70 8 10 4 1" 15
208 3 159.9 79.9 1.5 200 6 8 4/0 1½" 12
240 3 140.7 70.4 2.0 180 6 8 2/0 1½" 12
380 3 91.4 45.7 4.9 115 10 12 1 1" 12(WT)
480 3 70.4 35.2 7.9 90 12 12 3 1" 12(WT)
600 3 54.3 54.3 12.3 70 8 10 4 1" 15
208 3 178.6 59.5 1.4 225 8 10 4/0 1½" 17
600 3 63.4 63.4 10.9 80 8 10 4 ¾" 18
58.5
40.5
45
54
J6 and J16 Wiring Chart Notes:
1. Power feed wire sizing is based on using 75°C Cu THHN wire with feeder branch
protection rated at 125%.
2. Internal wire sizing is based on using 200°C SEW-2 or PTFE wiring in a raceway
with an ambient temperature up to 60°C.
3. For information on 277V, 415V, or 440V models reference the supplied drawing
or contact the factory.
4. Normal phase-to-phase resistance tolerance is ±5%.
5. 380, 480, and 600-volt phase-to-phase resistance values are shown with the transformer
disconnected.
6. For 575V models, m
ultiply the kW rating of the 600V model by a de-rating factor of 0.92
to get the actual rating for 575V.
7. For models manufactured prior to June 24, 2005, that utilize wiring diagrams 3, 5, 6,
7(NT), 7(WT), or 11 please contact the factory for wiring diagrams.