Installation Sheet

FIXTURE INSTALLATION
1. Determine the location for the lamp. Using the mounting plate as a template, mark the location of the holes for
the wall anchors.
2. Drill the appropriate size holes for the WALL ANCHORS(1). (the holes should be slightly smaller than the size of
the anchors.) Install the wall anchors to the hole.
3. Attach the MOUNTING PLATE (5) onto the junction box using the MOUNTING SCREWS (4). This fixture is
designed to be mounted on standard junction box. The junction box must be securely mounted to the structure
of the building. Screw in the WOOD SCREW (2) to the anchors.
4. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. fasten the wires together
with an approved fastener (WIRE NUT) (6). starting 1" below the fastener, tightly wrap the connection with
electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED
WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT!
5. Attach the ground wire (Green) to the ground inside the outlet box (Generally green or bar copper wire) or the
GROUND SCREW (3) on the MOUNTING PLATE (1). NEVER CONNECT GROUND WIRE TO "HOT" WIRE!
FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH!
6. Connect the black fixture leads to the hot (Generally black) wire in the junction box. fasten the joined wires same
as previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD
RESULT IN SERIOUS INJURY OR DEATH!
7. Attach the FIXTURE ASSEMBLY (7) to the MOUNTING PLATE (5) and secure it with the BALL NUT(9)
8. Screw the TYPE B LAMP (8) up into the socket of the fixture.THIS FIXTURE IS RATED FOR 40 WATT LAMP.
DO NOT EXCEED THE RECOMMENDED WATTAGE!
9. Lift the GLASS SHADE (10) up onto the FIXTURE ASSEMBLY (7) and secure it using the FINIAL(11).
10. Restore power to the outlet at the breaker or fuse box.
2
ITEM DESCRIPTION PART NUMBER
1 WALL ANCHORS HDW-001123
2 WOOD SCREW HDW-001123
3
GROUND SCREW
HDW-001123
4
MOUNTING SCREW
HDW-001123
5
MOUNTING PLATE MPT-001123
6
WIRE NUT
HDW-001123
7
FIXTURE ASSEMBLY FAS-001123
8
BULB NOT INCLUDED
9
BALL NUT
HDW-001123
10
GLASS SHADE GLS-001123
11
FINIAL FIN-001123
OSSINING
1123
INSTALLATION INSTRUCTIONS
WARNING/CAUTION
· DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS
COMPLETELY BEFORE STARTING INSTALLATION.
· TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL
APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND
MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED
FACTORY TRAINED TECHNICIAN.
· CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF
CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS
AFTER USE.
· REMOVE THE FIXTURE, PARTS AND PARTS BAG(S) FROM THE CARTON. BEFORE DISCARDING THE
CARTON, DOUBLE CHECK TO MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR
TO INSTALLATION FOR ANY DAMAGE TO THE FIXTURE.
· DIMMING: THE FIXTURE CAN BE CONTROLLED BY A WALL DIMMING DEVICE. ONLY USE
TRIAC/ELECTRONIC DIMMER. MAKE SURE THE CARTON IS MARKED FOR USE WITH LED COMPACT
FLUORESCENT-INCANDESCENT LIGHT SOURCE ONLY. THESE CAN BE PROVIDED BY YOUR LOCAL
ELECTRICAL DISTRIBUTOR, HOME CENTER, OR HARDWARE STORE.
· PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS
www.hvlgroup.com
Questions? We're here to help!
Contact us at [e-mail]
4
5
6
7
8
10
11
9
1 3