Product Manual

ManualsBrandsHudson ManualsHandheld SprayersPortable Super Sprayer — 2-Gallon Capacity

This sprayer operates with liquid under pressure. Failure to observe CAUTIONS and follow instructions for use and maintenance can cause tank, hose or other parts to become

corroded, weakened, and/or burst. This can result in SERIOUS INJURY or PROPERTY DAMAGE from forcible ejection of parts or high-pressure discharge of spray material.

DO NOT USE ANY FLAMMABLES IN THIS SPRAYER as it is not designed nor intended for such use. Some spray materials can ignite or explode. Do not spray in an enclosed

space, near an open flame such as found in a BBQ grill or water heater, near an electric motor or open switch, or any source of heat.

DO NOT SMOKE while spraying. Use of flammables could result in SERIOUS INJURY or PROPERTY DAMAGE from unintended ignition or explosion.

DO NOT USE ANY CAUSTICS OR ACIDS IN THIS SPRAYER, since these can damage or weaken the spray and its parts, resulting in SERIOUS INJURY or PROPERTY DAMAGE.

• Before using any pesticides or any other spray material in your sprayer, READ THE LABEL ON THE SPRAY MATERIAL CONTAINER AND FOLLOW EXACTLY ITS INSTRUCTIONS

FOR MIXING AND USE INCLUDING THE NEED FOR PROTECTIVE CLOTHING. Some spray materials are dangerous and should not be used in this sprayer as they can damage

the sprayer or its parts, or may be harmful to the user. This could result in SEROUS BODILY INJURY or PROPERTY DAMAGE.

• BEFORE USING YOUR SPRAYER, thoroughly INSPECT both inside and outside of the sprayer. Be sure the hose is securely attached to the tank and on/off valve, and that the

spray wand and nozzle are attached and not damaged. A loosely connected hose, on/off valve, spray wand or nozzle can come off when sprayer is under pressure and cause

SERIOUS INJURY or PROPERTY DAMAGE.

• DO NOT PRESSURIZE sprayer if tank, hose or other parts appear to be damaged, discolored, brittle, excessively soft or loose.

• DO NOT PUMP or use sprayer with head or body over pump as pressure in sprayer can forcibly eject pump if it is not properly locked in place, and this can cause SERIOUS INJURY.

• DO NOT use hot or boiling liquids in sprayer since this may weaken or damage tank, pump or hose.

• DO NOT PRESSURIZE WITH ANY MECHANICAL DEVICE such as an air compressor, since this can create dangerous pressure and bursting of parts and result in SERIOUS INJURY.

• Wear long-sleeved shirt, pants, gloves, goggles or similar protective clothing when spraying

• Do not leave residue or spray material in sprayer after use. It may damage or clog the sprayer or its parts.

• Empty, clean and drain sprayer tank and hose after each use, according to directions.

• Do not smoke or eat while mixing spray materials or spraying, and wash up afterwards.

• Use only Hudson replacement parts when servicing your sprayer. Other parts may not fit properly or may be weakened by spray materials and fail under pressure, resulting

in SERIOUS INJURY from forcible ejection of parts or unexpected high pressure discharge of spray material.

• WARNING: keep sprayer and all spray materials away from children and pets.

Before you assemble and use your sprayer, read the following Safety information. It is helpful and important!

Instruction 871-200 Poly Sprayer Instructions

DANGER!

CAUTION!

WARNING! Make sure you RELEASE ALL THE PRESSURE in the sprayer...

• Immediately after each use, even if you stop spraying for just a few minutes.

• Before removing pump, hose, spray wand or nozzle.

• Before trying to unclog nozzle, spray wand, shut-off valve or hose.

• Before servicing sprayer in any way.

• Before use when sprayer is left in the sun or other warm place for an extended period of time.

• 10 YEARS: Classic Plus™

• 5 YEARS: Comando™, PumpLess™, Bugwiser®, Suprema® Poly Bak-Pak®, Yard & Garden®, Bak-Pak®

• 3 YEARS: Porta-Spray™, Water Wagon™

• 2 YEARS: Yard and Garden™, Multi-Purpose™, Leader®, Farm & Garden™, Dusters

• 1 YEAR: X-Pert®, Professional™ sprayers, Super Sprayer, Industro®, Constructo®, Suprema® Stainless Steel Bak-Pak®, Commercial sprayers, Regulator™,

NeverPump™, Farm Tough™, Team Quencher™, Foam-a-Matic™, Stain-Preserve-Seal™ (SPS) and Surface Applicator sprayers, Bleach-Solutions™, Favorite®, EZ

Applicator™, Deck and Fence™, Quick ‘n Easy™, Weed ‘n Bug Eliminator™, Eliminator™, Eco™, Trombone®, Walk ‘n Water™.

• 90 DAYS: Fog®

H. D. Hudson Manufacturing Company warrants to the original consumer purchaser of this product at retail that it is free from defects in materials and workmanship for

the period specified above from the original date of purchase. This warranty does not apply to damage to the product resulting from accident, misuse, neglect, alteration,

modification, tampering, or failure to follow instructions supplied with the product. This warranty does not cover normal wear and tear of o-rings or seals, and, except

for Tek®, X-Pert®, Comando™, Constructo®, Industro®, and ULV™ sprayers, the warranty shall be void if the product is used commercially. If the product or any part

of it should malfunction within the warranty period, telephone our CUSTOMER SERVICE DEPARTMENT at 1-800-977-7293 for fast service. We will, at our option, repair or

replace any problem parts free of charge. This warranty is valid in North America. You must retain your sales receipt as proof of the date of purchase and include it with

any return of the product.

ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR CONSUMER USE, ARE LIMITED TO 1 YEAR. H. D. HUDSON

MANUFACTURING COMPANY EXCLUDES LIABLITY UNDER THIS WARRANTY FOR ANY AND ALL INCIDENTAL AND CONSEQUENTAL LOSS OR DAMAGES.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential loss or damage, so these

limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

LIMITED WARRANTY

IF YOU HAVE ANY QUESTIONS OR CONCERNS, OR ARE MISSING PARTS, DO NOT RETURN SPRAYER TO THE STORE!

PLEASE CALL OUR CONSUMER HOTLINE AT 1-800-9-SPRAYER

Visit us on the Internet: www.hdhudson.com

(1-800-977-7293)

Summary of content (15 pages)

PAGE 1
IF YOU HAVE ANY QUESTIONS OR CONCERNS, OR ARE MISSING PARTS, DO NOT RETURN SPRAYER TO THE STORE! PLEASE CALL OUR CONSUMER HOTLINE AT 1-800-9-SPRAYER Visit us on the Internet: www.hdhudson.com 1 Instruction 871-200 (1-800-977-7293) Poly Sprayer Instructions Before you assemble and use your sprayer, read the following Safety information. It is helpful and important! DANGER! This sprayer operates with liquid under pressure.
PAGE 2
Here’s How to assemble your sprayer If any part is missing, please call 1-800-9-SPRAYER (800-977-7293) to order a replacement. Check carton for: -Sprayer Tank with (may include Pressure Relief Valve, Quick Connect or hose adapter nut) -Pump (A) in tank -Hose Assembly with fitting and nut (may be loose in tank) -Shut-off Valve (B) (may be assembled to hose) -Spray Wand (C) with Nozzle (may be loose in tank) -Supply Tube (D) -Instructions (E) 2a. Insert supply tube into bottom end of hose fitting.
PAGE 3
Here’s Fill Your Sprayer Before filling, be sure to read, understand and follow exactly the label instructions on spray material container! 3a. With pump handle all the way down and in the locked position (A), turn to left (B) and lift out the pump (C) 3b. Pour measured amount of spray material into the open tank. Follow label directions on spray material container for amount to use. NOTE: Do not try to remove pump by unscrewing pump cap.
PAGE 4
6 Here’s how to release the pressure in your sprayer Warning: always release pressure before trying to service sprayer in any way or before removing or disconnecting nozzle, spray wand, shut-off valve, hose or any other part! 6a.Turn sprayer upside down and turn nozzle away from you. Squeeze lever or push button to on and let all the air escape. 7 6b.Turn sprayer up-right and slowly unscrew pump from tank and remove it. Keep face & body away from pump. 6c.
PAGE 5
CAUTION! Make sure pressure is released BEFORE removing cap nut. Always make sure cap nut is securely tightened onto tank before pressurizing. 7c. If you have a leak at hose connection or if nothing but air comes out of nozzle: Removing hose and supply tube: Release pressure! Unscrew the cap nut (no tools required) and lift hose and supply tube out. If sprayer leaks at hose connection: Clean and tighten cap nut or replace the O-ring inside cap nut.
PAGE 6
¡SI TIENE PREGUNTAS O DUDAS O SI HAY PIEZAS FALTANTES, NO DEVUELVA EL ASPERSOR A LA TIENDA DONDE COMPRO EL PRODUCTO! LLAME A NUESTRO DEPARTAMENTO DE SERVICIO AL CLIENTE AL 1-800-9-SPRAYER (1-800-977-7293) Visítenos en nuestro sitio Internet al: www.hdhudson.com 1 Instrucción 871-200 Instrucciones del rociador del polietileno Antes de ensamblar y utilizar el aspersor, lea cuidadosamente las instrucciones siguientes sobre la seguridad.
PAGE 7
2 ¿Cómo ensamblar su aspersor? Si falta alguna pieza, por favor comuníquese al 1-800-9-SPRAYER (800-977-7293) para ordenar el repuesto. Verifique que la caja contenga: -Tanque aspersor con (puede incluir válvula de descompresión, conector rápido o adaptador para manguera).
PAGE 8
3 Llene su aspersor ¡Antes de llenar su aspersor asegúrese de leer, entender y seguir exactamente las instrucciones del contenedor de material de aspersión! 3a. Con la manilla de la bomba colocada hacia abajo en la posición cerrada (A), gírela a la izquierda y levante la bomba (C) 3b. Vierta una cantidad moderada de material de aspersión dentro del tanque. Siga las indicaciones del contenedor del material de aspersión para saber qué cantidad utilizar.
PAGE 9
6 ¿Cómo liberar la presión de su aspersor? Advertencia: siempre libere la presión antes de intentar realizar el mantenimiento del aspersor de cualquier modo o antes de quitar o desconectar la boquilla, varilla pulverizadora, válvula de cierre, manguera o cualquier pieza. 6a. Voltee el aspersor boca abajo y aparte la boquilla de usted. Jale de la palanca o presione el botón para encender y dejar escapar el aire. 7 6b.
PAGE 10
¡PRECAUCIÓN! Asegúrese de liberar la presión ANTES de retirar la tuerca de la tapa. Siempre asegúrese de que la tuerca de la tapa esté bien ajustada al tanque antes de presurizar. 7c. Si hay una filtración en la conexión de la manguera o sólo sale aire de la boquilla: Extracción de la manguera y del tubo de suministro: Libere la presión! Desenrosque la tuerca de la tapa (no se necesitan herramientas) y levante la manguera y el tubo de suministro.
PAGE 11
EN CAS DE QUESTIONS OU DE PRÉOCCUPATIONS, OU S’IL MANQUE DES PIÈCES, NE RAMENEZ PAS L’APPLICATEUR EN MAGASIN! Si vous avez quelque problème ou une question, contactez notre service d’assistance à la clientèle 1-800-9-SPRAYER (1-800-977-7293) Visitez notre site Web: www.hdhudson.com 1 Instruction 871-200 Instructions de Pulvérisateur en poléthylène Avant d’assembler et utiliser, veuillez lire avec soin les renseignementssuivants relatifs à la sécurité.
PAGE 12
2 Comment assembler votre pulvérisateur S’il manque une pièce, composer le 1-800-9-SPRAYER (1-800-977-7293) pour commander une pièce de remplacement.
PAGE 13
3 Comment remplir votre pulvérisateur Avant de remplir, s’assurer de lire, de comprendre et de suivre attentivement les directives de l’étiquette du contenant de produit à pulvériser! 3a. Avec la poignée de la pompe complètement 3b. Verser la quantité exacte de 3c. Ajouter l’eau, tel qu’indiqué. Ne pas remplir au-delà produit à pulvériser dans l’ouverture de la ligne MAX FILL. Remettre la pompe en place et la du réservoir.
PAGE 14
6 Comment relâcher la pression de votre pulvérisateur Mise en garde : toujours relâcher la pression avant d’effectuer un entretien sur le pulvérisateur ou avant de retirer ou de déconnecter la buse, la rallonge, la soupape d’arrêt, le tuyau ou toute autre pièce! 6a. Retourner le pulvérisateur et pointer la buse loin de soi. Serrer la poignée ou appuyer sur le bouton et laisser l’air s’échapper. 7 6b.
PAGE 15
AVERTISSEMENT! S’assurer de relâcher la pression AVANT de retirer l’écrou-capuchon. Toujours s’assurer que l’écrou-capuchon est serré fermement sur le réservoir avant de pressuriser. 7c. Si le raccord du tuyau fuit ou si la buse ne propulse que de l’air: Retirer le tuyau et le tube d’alimentation: Relâcher la pression! Dévisser l’écrou-capuchon (aucun outil requis) et retirer le tuyau et le tube d’alimentation. S’assurer de relâcher la pression AVANT de retirer le tuyau ou la rallonge de la soupape.