Portable System Owners Manual Customer Service Center • N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A. Read and understand operator's manual before using this unit. Failure to follow operating instructions could result in injury or damage to property. REQUIRED TOOLS AND MATERIALS: Two People Wood Board (Scrap) Tape Measure Step Ladder 8 ft. (2.4 m) Tape Garden Hose or Sand 360 lb.
WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NOT HANG on the rim or any part of the system including backboard, support braces or net. • During play, especially when performing dunk type activities, keep player's face away from the backboard, rim and net. Serious injury could occur if teeth/face come in contact with backboard, rim or net.
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction material.
NOTICE TO ASSEMBLERS ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system. IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside.
Get to know the basic parts of your basketball system.....
PARTS LIST - (See Hardware Identifier) Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Qty. Part No.
HARDWARE IDENTIFIER (BOLTS & STEEL RODS) Item #23 (2) Item #8 (1) Item #22 (4) Item #11 (1) Item #7 (1) Item #16 (2) HARDWARE IDENTIFIER (NUTS & WASHERS) Item #14 (1) Item #10 (1) Item #17 (6) Item #21 (4) Item #12 (6) HARDWARE IDENTIFIER (PLASTIC SPACERS & CLIPS) Item #19 (12) Item #28 (2) * You may have extra parts with this model.
SECTION A: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section: HARDWARE USED IN THIS SECTION (not actual size) TOOLS REQUIRED FOR THIS SECTION 9/16” and 1/2” Item #7 (1) Item #8 (1) AND/OR Item #12 (6) Item #11 (1) Item #28 (2) 9/16” and 1/2” Item #16 (2) Item #17 (6) Item #10 (1) Item #14 (1) P/N 214653B 05/03 8
2. Correctly identify each pole 1. Remove contents from tank section and mark indicated distance from ends with tape (not supplied) as shown. 1 4 TOP TAPE (Not Supplied) MIDDLE 5” (13 cm) 5 6 BOTTOM 5” (13 cm) 3. IMPORTANT! Center the alignment slot of middle pole section (5) in the lower hole of top pole section (4) as shown. While maintaining alignment, bounce middle section of pole (5) into top section of pole (4) using wood scrap as shown until they no longer move toward taped reference mark.
4. IMPORTANT! Center the alignment slot of lower pole section (6) in the lower hole of middle pole section (4) as shown. While maintaining alignment, bounce top and middle pole assembly (4 & 5) onto bottom section of pole (6) using wood scrap as shown until they no longer move toward taped reference mark. NOTE: Pole sections should have a 3-1/2" (9 cm) minimum overlap. 4 5 5 6 6 WOOD SCRAP 5. Install rod (8) through holes in bottom pole section (6) and eyebolt (7).
6. 28 Install wheel axle (2) through wheel carriage (9). Install wheels (3) onto wheel axle (2) with spacers (28) as shown. Insert pole assembly into tank assembly as shown. Secure bottom pole (6) to tank and wheel bracket as shown, a deep socket is recommended. IMPORTANT! DO NOT OVER TIGHTEN. 9 3 6 28 3 2 IMPORTANT!: THE SPACER (28) WILL FIT LOOSELY UNTIL SECURED INTO THE CAVITY OF THE BASE. WARNING! 7 TWO PEOPLE REQUIRED FOR THIS PROCEDURE.
8. Secure non-secured ends of tank struts (13) to tank as shown. Repeat for opposite side.
SECTION B: ASSEMBLE THE BACKBOARD This is what your system will look like when you’ve finished this section: TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION 1/2” Item #17 (6) Item #19 (12) Item #21 (4) OR Item #23 (2) 1/2” Item #22 (4) 13 05/03 P/N 214653B
1. Mount brackets (20) and rim (18) to backboard and finger tighten as shown. NOTE: Final adjustments will be made in Step 11 22 21 18 Refer To Instructions Included With Rim Hardware For Rim Assembly.
2. Support pole and tank assembly over support table. Carefully slide backboard components onto pole. WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. SAWHORSE OR SUPPORT TABLE 3. While still in the horizontal position, carefully slide backboard components onto pole.
4. Install net clips. Installez les pinces du filet. Netzhalteklammern anbringen. Instale los sujetadores de la red. WARNING: Use of this product without proper installation of net clips, or when all net clips are not present could result in bodily harm. Be sure to follow directions carefully. CLIP “ARM” " BRAS " DE LA PINCE CLIP-ARM AVERTISSEMENT : L'utilisation de ce produit sans installer correctement ou toutes les pinces du filet risque de causer des blessures.
18 5. Install net. SIDE VIEW Installez le filet. VUE DE CÔTÉ SEITENANSICHT VISTA LATERAL NETCLIP PINCE DE FILET NETZHALTEKLAMMER SUJETADOR DE LA RED Das Netz anbringen Instale la red. 25 19 NET FILET NETZ RED Insert net into bottom of clip as shown. Insérez le filet dans la base de la pince, comme illustré. Das Netz wie gezeigt unten in den Clip stecken. Introduzca la red en la parte inferior del sujetador como se muestra. Twist net until it snaps into position. Net must be centered through clip.
SECTION C: APPLY HEIGHT AND MOVING LABEL & SECURING SYSTEM 1. Carefully upright assembly. Apply moving system label (15) to front of pole as shown. Regulation rim height is 10 feet (3.05 m). WARNING! 10 feet (3.05 m) TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 15 WARNING! DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. 2. Place assembled unit to desired location.
05/03 P/N 214653B Tragbares Basketball-System Benutzerhandbuch Zwei Personen Holzbrett (Ausschuß) Bandmaß Treppenleiter, 8 Fuß (2,4 m) Klebeband Gartenschlauch oder Sand (163 kg) (360 US-Pfd.) Hammer Schraubenschlüssel: (Zwei) 1/2 Zoll, (Ein), 9/16 oder verstellbare große und kleine Schraubenschlüssel (9/16-ZollEinsatz mit Verlängerung empfohlen) Sägebock oder Auflagetisch Schutzbrille TRANSPORT DES SYSTEMS 1. Die Basketballrückwand auf die unterste Position einstellen. 2.
ANLEITUNG IN DEUTSCHER SPRACHE WICHTIG! NOTIEREN SIE SICH DIE MODELLNUMMER AUS DEM KÄSTCHEN AUF SEITE 1 DIESES BENUTZERHANDBUCHS 1. Den Tank (1) leeren. 2. Jedes Stangenteil richtig identifizieren und den angegebenen Abstand von beiden Enden wie gezeigt mit Klebeband markieren. 3. WICHTIG! Den zur leichteren Ausrichtung vorgesehenen Schlitz am mittleren Stangenteil (5) wie gezeigt in einem tieferen Loch des oberen Stangenteils (4) zentrieren.
05/03 P/N 214653B Una Compañía Huffy TUFF STUFF® y las marcas comerciales asociadas son propiedad de Mattel, Inc. y se usan con su permiso. Mattel, Inc. y todas sus compañías afiliadas o subsidiarias de ninguna forma patrocinan, aprueban ni autorizan los productos Huffy. Para obtener más información sobre el montaje, ubicación, uso y mantenimiento adecuados visite el sitio en la red de The American Basketball Council en http://www.smarthoops.
INSTRUCCIONES EN ESPAÑOL ¡IMPORTANTE! ANOTE EN LA PÁGINA 1 DE ESTE MANUAL DEL PROPIETARIO EL NÚMERO DE MODELO QUE APARECE EN LA CAJA. 1. Saque el contenido del tanque (1). 2. Identifique correctamente cada sección del poste y marque con cinta la distancia indicada desde los extremos, como se muestra. 3. ¡IMPORTANTE! Centre la ranura de alineación de la sección media del poste (5) en el orificio inferior de la sección superior del poste (4), como se muestra.
05/03 P/N 214653B Customer Service Center • N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A. Deux personnes Mètre Planche (rebut) Clés: (2) 7/16”, 1/2”, 9/16”, 3/4” ou petite ou grande clé réglabe Lunettes de sécurité Chevalet de scieur ou table de soutien Echelle de 2,4 m (8 pieds) Tuyau d’arrosage ou sable (102 kg) (225 lb.) Marteau Ruban adhésif Tournevis cruciforme Ciseaux POUR REGLER LE PANNEAU : 1. Réglez le panneau de basket-ball à la hauteur la plus basse. 2.
INSTRUCTIONS EN FRANÇAIS IMPORTANT ! NOTEZ À LA PAGE 1 DE CE MANUEL LE NUMÉRO DE MODÈLE MENTIONNÉ SUR LE CARTON. 1. Retirez le contenu du réservoir (1). 2. Identifiez correctement chaque section de poteau et marquez la distance indiquée à partir des extrémités avec le ruban adhésif, comme illustré. 3. IMPORTANT ! Centrez la fente d'alignement de la section de poteau centrale (5) sur un trou inférieur de la section de poteau supérieure (4), comme illustré.