Display System Owners Manual Customer Service Center • N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A. Model 89226 WARNING! REQUIRED TOOLS AND MATERIALS: READ AND UNDERSTAND OPERATOR'S MANUAL BEFORE USING THIS UNIT. • 2 People FAILURE TO FOLLOW OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY. • 2 Stepladders • (2 each) Wrenches and/or Socket Wrenches and Sockets.
NOTICE TO ASSEMBLERS ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to the instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system. IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside.
PARTS LIST (See Hardware Identifier) Item Qty. Part No. Description Item Qty. Part No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Bracket, Reinforcement S/J P/S Cover Screw, #8 x 3/4", Flat Hd, Phillips Spacer, Mounting Net Clips Plastic Knob Bolt,Hex-Flange, 5/16-18 x 3" NBA Sticker Locknut, 3/8-16 Nylon Insert Bolt, Carriage, 5/16-18 x 2.25" Nut, Hex-Flange 5/16-18 Whiz Lock Bolt, Carriage, 5/16-18 x 3.5" Bolt, U, Round, 3/8-16 x 3.
Install display boards in the marked locations. Each mounting location consists of a mounting pole stub with the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicate direction the board is facing).
1a. At corner location 3 slide the pole sleeve (34) inside the mounting stub. 34 1b. Slide the 3" diameter end of the display pole (24) inside the pole sleeve. 24 Secure the display pole by sliding the display wedge (27) into position as shown. To lock the display pole in place, tighten the hex-bolt (19). 24 27 19 2a. At corner location 1, 2 and 4 slide the 3-1/2" diameter end of the display pole (33) inside the mounting stubs. 2b.
Corner Location 1: STEEL FRAME ACRYLIC BACKBOARD ASSEMBLY 11 Display Stand - Top View 3-1/2" 31 3" Corner “4” 80602 Corner “3” 61259 32 4 Corner “2” 73256 Corner “1” 9H235A 3-1/2" 3-1/2" 18 1. Insert “T” bolt (18) through Slam Jam bracket (23) as shown. Secure Slam Jam bracket (23), extension arm (31) and mounting spacers (4) assemblies to backboard using bolt (7 ) and nut (11) as shown. 23 7 2. Attach board assembly to pole. 32 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE.
NOTE: 3. Tighten nut (17) until flush with end of "T" bolt (18) as shown here. • Fit rim (25) securely into bracket (23) as shown. • Install reinforcement bracket (1) onto “T” bolt (18) as shown. • Install spring (16) onto “T” bolt (18) as shown. • Install special nut (17) and washer (15) onto “T” bolt (18). 25 17 18 NOTE: Peel protective film from surface of acrylic backboard prior to use. 4. Attach cover (2) to rim using screws (3). 15 16 1 23 5. Apply logo label (8) to rim cover (2).
Corner Location 2: 48” FAN MOLDED PLASTIC BOARD ASSEMBLY 11 Display Stand - Top View 3-1/2" 3" Corner “4” 80602 31 Corner “3” 61259 28 Corner “2” 73256 Corner “1” 9H235A 3-1/2" 3-1/2" 1. Insert “T” bolt (18) through Slam Jam bracket (23) as shown. Secure Slam Jam bracket (23) and extension arm (31) to backboard using bolt (7) and nut (11) as shown. 18 18 Tighten completely. 23 7 2. Attach board assembly to pole. 28 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE.
3. • Fit rim (25) securely into bracket (23) as shown. • Install reinforcement bracket (1) onto “T” bolt (18) as shown. • Install spring (16) onto “T” bolt (18) as shown. • Install special nut (17) and washer (15) onto “T” bolt (18). 25 17 18 NOTE: Tighten nut (17) until flush with end of "T" bolt (18) as shown here.
Corner Location 3: 44" FAN MOLDED PLASTIC BOARD ASSEMBLY 1. Pole bracket will need to be lightly pressed into backboard ribbing. Be sure to press completely into place. Attach rim (25) to backboard and pole bracket (26) with knob (6), reinforcement bracket (1), and carriage bolt (10) as shown. Tighten knob completely. Display Stand - Top View 3-1/2" 3" Corner “4” 80602 Corner “3” 61259 WARNING! KNOB MUST BE TIGHTENED COMPLETELY AND CHECKED FOR TIGHTNESS BEFORE EACH USE.
Corner Location 4: 44" FAN MOLDED PLASTIC BOARD ASSEMBLY 11 Display Stand - Top View 3-1/2" 31 3" Corner “4” 80602 Corner “3” 61259 30 Corner “2” 73256 Corner “1” 9H235A 3-1/2" 3-1/2" 1. Attach rim (25) to backboard (30) and extension arm (31) with bolts (7), washers (14) and nuts (11). 14 25 Tighten completely. 7 2. Attach board assembly to pole. 30 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
11. Install net clips. CLIP “ARM” WARNING! USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS®, OR WHEN ALL SMART CLIPS® ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW DIRECTIONS CAREFULLY. CLIP “BODY” 25 Insert one “arm” of clip into ram as shown. Twist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows. 5 A Push second “arm” back and into ram as shown.
12. Install net. 25 SIDE VIEW 20 5 NETCLIP NET Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position. Net must be centered through clip.