User manual

9
05/03 P/N 214999C
INSTRUCTIONS
IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF
THIS OWNERS MANUAL
1. Remove contents from tank (1).
2. Correctly identify each pole section and mark indicated distance from
ends with tape as shown.
3. IMPORTANT! Center alignment slot of middle pole section (5) in a
lower hole of top pole section (4) as shown. While maintaining
alignment, bounce pole top (4) and middle section (5) together as shown
until they no longer move toward taped reference mark. Upright
assembly. NOTE: Pole sections should have a 3-1/2" (9 cm) minimum
overlap.
4. IMPORTANT! Center alignment slot of lower pole section (6) in a
lower hole of middle pole section (5) as in step 3. While maintaining
alignment, bounce assembly and lower pole section (6) together as
shown until they no longer moved toward taped reference mark.
NOTE: Pole sections should have a 3-1/2" (9 cm) minimum overlap.
5. Install rod (7) through holes in bottom pole section (6) and eyebolt (8).
6. Install wheel axle (2) through wheel carriage (19) and install wheels (3)
onto wheel axle (2) with spacers (17) as shown. Insert pole assembly
into tank assembly as shown. Secure bottom pole (6) section to tank
and wheel carriage as shown. A deep socket is recommended.
NOTE: Two people recommended for this step.
IMPORTANT! DO NOT OVER TIGHTEN.
7. Secure base struts (10) to pole using bolt (11), washers (12), and nut
(13), as shown. Rotate the non-secured ends of base struts (10) as
shown.
WARNING: TIGHTEN BOLT (11) IN LOCKNUT (13) UNTIL FLUSH
(EVEN) WITH LOCKNUT’S OUTER EDGE.
8. Secure base struts (10) to base using bolt (15), washers (12), and
nut (16).
9. Install pole mount bracket (27) and reinforcement bracket (56) with
carriage bolts (28) as shown. Tighten flange nuts (16) completely.
10. Assemble backboard brackets (29) using spacers (33) bolts (34, 35) and
nuts (36, 37) as shown.
11. IMPORTANT! Test fit bolts into holes of backboard brackets(29) and
carefully rock them in a circular motion to ream out paint from holes if
necessary. Attach lower elevator tubes (41) to backboard brackets (29)
using spacers (42) bolt (43) and nut (39) as shown.
12. WARNING: TWO PERSON MINIMUM REQUIRED FOR THIS
PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY
RESULT IN BODILY INJURY.
Insert “T” bolt (58) through Slam Jam bracket (57) as shown.
Secure Slam Jam bracket (57) and backboard bracket (29) assemblies
to backboard. Bend upper halves of backboard brackets (29) to line up
with holes in backboard and secure with bolts (32) and nuts (16).
Tighten completely.
13. Attach upper elevator tubes (44) to backboard brackets (29) using
spacers (42) bolt (43) and nut (39) as shown.
14. WARNING: TWO PERSON MINIMUM REQUIRED FOR THIS
PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY
RESULT IN BODILY INJURY.
Support pole on sawhorse. Attach upper and lower elevator tubes (44,
41) to upper pole section (4) using bolts (43) and nuts (39) as shown.
Attach pole cap (22) as shown.
15. Insert locking pin (46) into bracket on adjustment tube (49). Insert cross
pin (45) through hole in bracket and locking pin (46) as shown in figure
A. Fit left handle (47) onto adjustment tube (49) so the bottom of
adjustment tube (49) sits on the two small ribs of the handle as shown in
figure B.
16. Insert spring (50) into back of locking pin (46) as shown. Spring (50)
should rest between two small ribs at the back of the plastic handle as
shown in Figure C. Insert top of trigger (55) into bracket on the
adjustment tube (49) as shown. The plastic post of the handle pieces
should go through the hole in bottom of trigger (55) and hold it into place
as shown.
17. Finish handle assembly by attaching right handle (48) using screws (18)
as shown.
18. Attach adjustment tube (49) to lower elevator tubes (41) using bolt (43)
spacers (51) and nut (39) as shown.
19. WARNING: TWO PERSON MINIMUM REQUIRED FOR THIS
PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY
RESULT IN BODILY INJURY.
WARNING: DO NOT LEAVE ASSEMBLED UNIT UNATTENDED
WHEN EMPTY, MAY TIP OVER.
Insert lower adjustment rod (52) into bottom of adjustment tube (49), pull
trigger to allow lower adjustment rod to move about mid-way into
adjustment tube (49), release the trigger so the lower adjustment rod
(52) locks into position midway inside the adjustment tube (49). Attach
the lower adjustment rod (52) to elevator bracket (27) using bolt (53) and
nut (13) as shown.
20. Fit rim (21) securely into bracket (57) as shown.
Install reinforcement bracket (59) onto “T” bolt (58) as shown.
Install spring (30) onto “T” bolt (58) as shown.
Install special nut (40) and washer (38) onto “T” bolt (58).
Tighten nut (40) until flush with end of “T” bolt (58).
WARNING: USE OF THIS PRODUCT WITHOUT PROPER
INSTALLATION OF SMART CLIPS, OR WHEN ALL SMART CLIPS
ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE
TO FOLLOW DIRECTIONS CAREFULLY.
21. Install net clips as shown. (See illustration)
22. Install net as shown. (See illustration)
23. WARNING: DO NOT LEAVE ASSEMBLY UNATTENDED WHEN
EMPTY, MAY TIP OVER.
WARNING: TWO PERSON MINIMUM REQUIRED FOR THIS
PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY
RESULT IN BODILY INJURY.
Roll the completed assembly to the desired playing area. Insert the
T-strap (14) through the slot on the back of the base as shown. Secure
the unit to ground by twisting the tie down stake (23) into the ground and
hooking the T-strap (14) onto the tie down stake (23). Fill tank with 33
gallons of water.
IMPORTANT! Add two gallons (7.6 Liters) of non-toxic antifreeze in
sub-freezing climates.
24. Apply the height adjustment and moving label (25) to the front of the
pole as shown.
25. Lock elevator system into highest position (so the backboard is as high
as it will go). Apply 10 ft. height indication sticker (54) to adjustment rod
(52) directly below arrow on handle as shown. Move elevator system to
the next position and apply the 91/2 ft. sticker. Repeat until all height
settings have been labeled. (8-10ft.)
26. Pull trigger (55). Move elevator system up or down to desired height,
release trigger (55) to lock system into one of the five height settings.
WARNING: DO NOT ALLOW CHILDREN TO ADJUST HEIGHT.
WARRANTY CARD:
Please remember to complete your product
registration form either
on-line at: www.huffysports.com/warrantycard
or mail-in the enclosed postcard.