Portable Basketball System Owners Manual Customer Service Center • N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A. STROPSYFFUH REQUIRED TOOLS AND MATERIALS: • Tape Measure • Wood Board (scrap) • (2 each) Wrenches and/or Socket Wrenches and Sockets (Deep-Well Sockets are Recommended). 7/16" 1/2" 9/16" 3/4" AND/OR READ AND UNDERSTAND OPERATOR'S MANUAL BEFORE USING THIS UNIT. FAILURE TO FOLLOW OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY.
WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NOT HANG on the rim or any part of the system including backboard, support braces or net. • During play, especially when performing dunk type activities, keep player's face away from the backboard, rim and net. Serious injury could occur if teeth/face come in contact with backboard, rim or net.
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper and complete assembly, use, and supervision are essential for proper operation and to reduce the risk of accident or injury.
PARTS LIST (See Hardware Identifier) Item Qty. Part No.
HARDWARE IDENTIFIER (BOLTS & SCREWS) Item #4 (1) Item #57 (6) Item #65 (1) Item #10 (1) Item #5 (1) Item #23 (1) Item #19 (1) Item #16 (1) Item #54 (3) Item #26 (6) Item #53 (1) Item #21 (1) Item #50 (1) Item #60 (4)* Item #61 (4) Item #14 (2) Item #46 (2) Item #36 (1) HARDWARE IDENTIFIER (CONTINUED) 5 09/04 P/N 211574
HARDWARE IDENTIFIER (NUTS & WASHERS) Item #58 (7) Item #15 (20)* Item #37 (3)* Item #11 (7)* Item #55 (1) Item #8 (4) Item #20 (8)* Item #62 (4)* Item #12 (1) HARDWARE IDENTIFIER (STEEL SPACERS, RODS & CLIPS) Item #51 (2) Item #33 (2)* HARDWARE IDENTIFIER (PLASTIC SPACERS, CAPS & CLIPS) Item #67 (8) Item #59 (4) Item #49 (12) Item #32 (2) Item #29 (4) P/N 211574 09/04 Item #13 (1) *You may have extra parts with this model.
BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test-fit large bolts into large holes of elevator tubes, backboard brackets, and triangle plates. Carefully rock them in a circular motion to ream out any excess paint from holes if necessary. AVANT DE COMMENCER ! Pour garantir l'utilisation optimale du panneau, les composants du système élévateur et la visserie doivent être bien ajustés (serrés).
1. MIDDLE Identify pole sections. 2 5" (13 cm) 1 3 ID Sticker TOP BOTTOM 5" (13 cm) ID Sticker While maintaining alignment, bounce middle pole section (2) into top section (1) 2. using a wood scrap as shown until the top pole no longer moves toward the pole identification sticker on the middle pole. NOTE: IMPORTANT!: POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. Align dimple of top pole section (1) into trough of middle pole section (2) as shown.
3. Bounce top and middle pole assembly (1 & 2) onto bottom pole section (3) using a wood scrap as shown. Bounce until the top and middle pole assembly no longer moves toward the pole identification mark on the bottom pole. NOTE: IMPORTANT!: POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. Align dimple of middle pole section (2) into trough of bottom pole section (3) as shown. CAUTION! THE IDENTIFICATION STICKER IS LOCATED 5" FROM THE END OF THE POLE.
4. Install wheels (17) onto axle (28) and wheel bracket (25) with push caps (29) as shown. 17 29 17 25 28 29 5. Position base as shown. Secure wheel bracket assembly with bolt (16) and nut (15) as shown.
6. Install rod (4) through holes in bottom pole section (3) and eyebolt (5). Insert pole assembly into tank (6) and through center hole on wheel assembly as shown. Secure pole assembly with strap (44), washer (11) and lock nut (8). WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
7. Secure base struts (9) to pole using bolt (10) washers (11) and nut (12) as shown. 3 11 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 12 11 10 13 9 NOTE: ORIENTATION OF STRUTS Rotate the non-secured ends of base struts (9) as shown.
8. Secure base struts (9) to base using bolt (14) washers (11) and nut (15). 14 WARNING! 9 TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 11 11 15 9. Install upper pivot bracket (18) to front of base using bolt (19), washer (20) and nut (8) as shown.
10. Insert bolt (21) through lower pivot bracket (22) as shown, bolt (21) will be secured during step 13. Carefully place base assembly on its side. Install lower pivot bracket (22) with bolt (23), washers (20) and lock nut (8) as shown. IMPORTANT!: DO NOT OVER TIGHTEN 21 18 20 20 23 11. 8 22 Secure both hinge tubes (24) to second wheel bracket (25) with carriage bolts (26) and flange nuts (15). 26 24 25 15 24 IMPORTANT!: WICHTIG!: ¡IMPORTANTE!: NOTE ORIENTATION NOTEZ L'ORIENTATION.
12. Install wheels (27) onto axle (28) and wheel bracket (25) with push caps (29) as shown. 27 IMPORTANT!: 25 29 28 27 29 SIDE OF WHEEL WITH LONGER PLASTIC AXLE NEEDS TO FACE THE WHEEL BRACKET. 13. Position base as shown. Secure wheel bracket assembly with disc (30), washer (20) and nut (8) as shown. 14. Carefully reposition entire assembly as shown: 21 30 20 8 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE.
15. Install pole mount bracket (45) and reinforcement bracket (47) with carriage bolts (46) as shown. Tighten flange nuts (15) completely. 15 45 15 47 46 46 1 16. Attach spacers (32, 33) to pole mount bracket (45) with bolts (54), washers (20), and lock nuts (37) as shown. IMPORTANT! Tighten just until washers (20) stop moving.
. Assemble lanyard (34) to locking pin (35) as shown (FIG A). Attach covers (48) onto pole mount bracket (45) with carriage bolt (50) and nut (15) as shown. IMPORTANT!: 48 15 Loop end of pin lanyard (34) over carriage bolt (50) as it passes through the pole mount bracket (45) during this assembly. 45 FIG. A 48 34 50 50 34 FRONT SIDE 35 35 18. Apply logo and height indicator labels (41) to adjustment rod (31) as shown.
Insert handle assembly through pole mount assembly as 19. shown. Lock pole assembly in place at the 10’ (3.05 m) mark with pin (35). 35 Install spacers (51) onto backboard brackets (52), with bolts (53, 54) and lock 20. nuts (55, 37) as shown. 52 55 37 51 53 54 IMPORTANT!: KEEP HARDWARE LOOSE UNTIL AFTER STEP 25 IS COMPLETED.
21. Identify elevator tubes (63 & 56). Toward Board Toward Pole 63 Upper Elevator tube Toward Board Toward Pole 56 Lower Elevator tube Attach lower elevator tubes (56) and counter balance spring (68) to backboard support brackets (52) using spacers (59), bolt (57), and nut (58) as shown.
Starting with nuts (15) flush 22. against bracket (52) secure rim 15 52 (70) and bracket to backboard. 68 15 IMPORTANT! For spring loaded rim assembly, refer to instructions included with rim hardware. NOTE: Rim mounting nuts and bolts supplied with rim hardware. NOTE: DO NOT use washers here on spring return style rims. 62 60 70 Attach upper elevator tubes (63) to backboard support brackets (52) using spacers 23. (59), bolt (57), and nut (58) as shown.
24. Support pole on sawhorse. Attach backboard assembly to top pole section (1) as shown. Install pole cap (64). NOTE: Two people are recommended for this step. Use caution; elevator assembly is heavy. 58 1 56 67 58 66 64 66 67 65 56 57 25. Install upper elevator tubes (63) to triangle plates (66) as shown. Install handle assembly to lower elevator tubes (56) using bolt (57), spacers (67), and nut (58) as shown. NOTE: Before going on to next step, set adjustable system assembly to the 10’ (3.
26. Insert bolt (57) through left side upper elevator tube (63), then stretch spring (68) onto bolt (57). Insert bolt (57) through right side upper elevator tube (63) and secure with nut (58). WARNING! USE EYE PROTECTION WHEN INSTALLING SPRINGS.
SECTION D: INSTALL FRONT COVER & HANDLE 27. Upright system and fill base (8) with water (approx. 40 gallons) and snap fill cap (42) in place. WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 42 8 WARNING! DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. CAUTION! ADD TWO GALLONS (7.6 LITERS) OF NON-TOXIC ANTIFREEZE IN SUBFREEZING CLIMATES. NOTE: SA ND (3 (1 60 l 63 b kg .) ) 44 28.
29. Roll assembly to desired playing area. Secure assembly to ground using strap (44) and tie down stake (7). 30. Apply height and moving label (43) to front of pole as shown. 8 HEIGHT ADJUSTMENT TO ADJUST BACKBOARD: 1 2. Move elevator up or down to desired height. 44 3 1. While holding handle, remove pin. 43 2 3. Replace pin full length to lock system at desired height. 2 10 feet (3.05m) 7 MOVING SYSTEM 1 1. Adjust basketball backboard height to lowest position. 2.
32 Install net clips. Installez les pinces du filet. Netzhalteklammern anbringen. Instale los sujetadores de la red. WARNING: Use of this product without proper installation of net clips, or when all net clips are not present could result in bodily harm. Be sure to follow directions carefully. CLIP “ARM” " BRAS " DE LA PINCE CLIP-ARM AVERTISSEMENT : L'utilisation de ce produit sans installer correctement ou toutes les pinces du filet risque de causer des blessures.
70 33. Install net. SIDE VIEW Installez le filet. VUE DE CÔTÉ SEITENANSICHT VISTA LATERAL NETCLIP PINCE DE FILET NETZHALTEKLAMMER SUJETADOR DE LA RED Das Netz anbringen Instale la red. 69 49 NET FILET NETZ RED Insert net into bottom of clip as shown. Insérez le filet dans la base de la pince, comme illustré. Das Netz wie gezeigt unten in den Clip stecken. Introduzca la red en la parte inferior del sujetador como se muestra. Twist net until it snaps into position. Net must be centered through clip.
