Pro Image Rim Owners Manual Customer Service Center • N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A. WARNING! READ AND UNDERSTAND OPERATOR'S MANUAL BEFORE USING THIS UNIT. FAILURE TO FOLLOW OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY. TOOLS AND MATERIALS REQUIRED FOR ASSEMBLY: • Two People • Step Ladder, 8 ft. (2.4 m) • Wrenches (One) 3/4", (Two) 9/16” and (Two) 1/2” or (Two) Adjustable Wrenches Toll-Free Customer Service Number for U.
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction material.
NOTICE TO ASSEMBLERS ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to the instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system. IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside.
Get to know the basic parts of your basketball system..... RIM BACK BRACKET BACK BRACKET PARTS LIST - See Hardware Identifier Item Qty. 1 1 2 2 3 2 4 2 5 2 6 8 7 2 8 2 9 2 10 2 11 2 12 2 13 1 14 1 15 1 16 4 17 4 18 1 19 1 20 2 21 2 22 2 23 1 P/N 211644 11/03 Part No. 202604 203474 203017 203063 203232 200484 202601 202602 202523 203439 220140 908087 108085 918086 201611 203100 204290 202655 202636 203795 202603 202531 Description Rim Bolt, Carriage 3/8 x 4.75” Long Washer, Flat, 1”O.D.
HARDWARE IDENTIFIER (BOLTS & SCREWS) Item #2 (2) Item #12 (2) Item #16 (4) Item #11 (2) HARDWARE IDENTIFIER (NUTS & WASHERS) Item #5 (2) Item #21 (2) Item #8 (2) Item #3 (2) Item #4 (2) Item #17 (4) Item #20 (2) Item #6 (8) Item #9 (2) HARDWARE IDENTIFIER (METAL SPACERS & NYLON WASHERS) Item #10 (2) Item #22 (2) 5 11/03 P/N 211644
1. Install two carriage bolts (2) through rim (1), washers (3), and lock washers (9) as shown. Tighten nuts (4) completely. NOTE: Perform this step twice as it is applied to both holes of rim bracket shown 2 1 NOTE: COMPLETED ASSEMBLY: 3 9 4 2. Place a special locking nut (20) approximately half-way up on each carriage bolt (2) as shown. Keep the two special locking nuts (20) at the same level.
3a. First, test fit spacer (10) into back bracket (13) and Carefully rock in a circular motion to ream out any excess paint from holes if necessary. 13 10 3b. Place rim (1) into back bracket (13) so that the holes are properly aligned. 1 13 3c. Line up holes 20 Then, insert spacer (10) through back bracket (13), nylon washers (22) and rim assembly (1). BOTTOM VIEW NOTE: Ends of spacer (10) should be flush on both sides of board bracket (13).
4. Install bolt (11) through top holes on bracket (13) using washers (6) and nut (5) as shown. Tighten completely. 10 6 6 5 22 22 11 5. Attach rim assembly to backboard and support structure by inserting bolts (16) through bottom holes in back bracket (13). Secure with nuts (17) and washers (6). Tighten nuts (17) completely.
6. Position rim assembly (1) 90 degrees to back bracket (13) as shown. Place inner-bracket (14) over both carriage bolts (2) followed by springs (7), washers (8) and special nuts (21). NOTE: NOTE: COMPLETED ASSEMBLY: Tighten special nuts (21) until flush with end of carriage bolts (2) as shown. NOTE: Do not over tighten as rim will not flex properly. See leveling instructions (Step 11) to determine how much to tighten nuts (20) and (21). 13 1 14 7 8 21 2 20 Lower lower rim down.
8. Secure back bracket (13) fully to backboard by inserting bolts (16) through upper holes in back bracket (13), Add washers (6) and nuts (17) to bolts (16). Tighten nuts (17) completely. 17 16 6 9. First, test fit spacer (10) into back bracket (13) and Carefully rock in a circular motion to ream out any excess paint from holes if necessary. Insert spacer (10) through bottom holes in board bracket (13) and inner bracket (14).
10. Then, install bolt (11), washers (6), and nut (5) through spacer (10) and tighten completely. 5 11. 6 6 11 LEVELING AND TENSION ADJUSTING INSTRUCTIONS: Adhere leveling and tension adjusting label (23) to inside of rim cover plate (15). 23 TO LEVEL RIM, TIGHTEN OR LOOSEN THESE NUTS 20 TO ADJUST RIM TENSION , TIGHTEN OR LOOSEN THESE NUTS 21 202531 Place level on rim (1) and adjust nut (20) until level. Tighten nut (21) to set rim tension for playing.
. Apply logo label (19) to cover plate (15). Install cover plate (15) on rim (1) using self tapping screws (12) as shown (note orientation of cover plate). NOTE: Cover plate (15) will fit over back bracket. 19 15 12 15 15 15 13. Secure net (18) to rim (1). 1 1 2 NOTE: Official rim height is 10-0’ (3.05 m) from top of rim to playing surface. OUTSIDE VIEW 4 3 P/N 211644 11/03 10 feet (3.
