Installation Instructions
Table Of Contents
- Title page
- Contents
- About this manual
- Safety information
- Ch 1 - Introduction
- Ch 2 - Adding cards to the Controller
- Unpacking the System Controller
- Unpacking the picocells
- System Controller card configuration
- Adding cards to the System Controller (first steps)
- Jumper and DIP switch settings
- Attaching bus cables
- Adding cards to the System Controller (final steps)
- Configuring Controller cards
- Verifying the card configuration
- Ch 3 - Installing the Controller
- Ch 4 - Verifying the Controller configuration
- Ch 5 - Configuring the router
- Ch 6 - Testing picocells
- Ch 7 - Installing picocells
- Ch 8 - Connecting to external equipment
- Ch 9 - System testing
- Ch 10 - Installation inspection
- Ch 11 - Provisioning
- Ch 12 - Remote Client
- Ch 13 - Troubleshooting
- Ch 14 - Maintaining Quad T1 cards
- App A - Specifications
- App B - Standards compliance information
- App C - Part numbers
- App D - Updates and backups
- Index
1026209–0001 Revision B Index-3
J
Jumper settings, Controller cards, 2–13
L
LAN cards, 2–19
driver, 8–9
installing a second LAN card, 8–9
IP address, 8–10
Launching the AIReach Office application, 2–28,
4–2
LDN (local directory number), 4–22, 11–2
LEDs
picocells, 6–5, 7–17
illustrated, 13–8
Quad T1 cards, 6–6
illustrated, 6–7
Login, 2–28, 4–2
remote access, 12–3
M
Materials required for installation, 1–12
MIN (mobile identification number), 6–23
range, 4–22, 11–1
Mobile phones, configuration to receive alarms,
8–12
Modem
external, 8–11
internal, 2–19
Mounting, options, Controller, 1–3
Mounting – rack mount. See Rack mounting
Mounting, options, Controller, 2–2
Mounting plate, picocell, 1–7
fasteners, 7–3
installing, 7–2
locking, 7–12
unlocking, 2–6
Moving a Quad T1 card, 14–5
MSC Configuration window, 4–19
MVIP bus, 2–14
cable, 2–23
MVIP bus cable, 14–2
O
OMC software, description, 4–2
Operating mode, 6–16
Optional equipment, C–3
Organization of this manual, xi
P
Pagers, configuration to receive alarms, 8–12
Part numbers, C–1
Password, 2–28, 4–2, 12–3
PBX connections, 8–2
checking, 14–4
Performance testing, 9–2
checklist, 9–2
Picocells
alarms, 13–8
table, 13–9
antenna, A–6
cabling, T1, 7–11
cell information, 4–12
compliance information, B–2
components, 1–7
part numbers, C–2
connecting for testing, 6–2
connections at telco closet, 7–15
connectors, 7–8
illustrated, 6–3
pinouts, 7–8
controller, 1–7
description, 1–2
dimensions, A–4
installing, 7–2, 7–7
preparing for installation, 7–1
IP addresses, 13–2
LEDs, 6–5
illustrated, 13–8
line cord, 7–7
mounting. See Picocells, installing
mounting plate, 1–7
fasteners, 7–3
installing, 7–2
locking, 7–12
unlocking, 2–6
power requirements, 6–4
power supply, 1–7, 1–12, 6–2, 6–4, 7–1
connecting, 7–14
specifications, A–6
power switch, 6–6, 7–12
RF levels, A–6
scanning receiver, 1–7