Installation Instructions
Table Of Contents
- Title page
- Contents
- About this manual
- Safety information
- Ch 1 - Introduction
- Ch 2 - Adding cards to the Controller
- Unpacking the System Controller
- Unpacking the picocells
- System Controller card configuration
- Adding cards to the System Controller (first steps)
- Jumper and DIP switch settings
- Attaching bus cables
- Adding cards to the System Controller (final steps)
- Configuring Controller cards
- Verifying the card configuration
- Ch 3 - Installing the Controller
- Ch 4 - Verifying the Controller configuration
- Ch 5 - Configuring the router
- Ch 6 - Testing picocells
- Ch 7 - Installing picocells
- Ch 8 - Connecting to external equipment
- Ch 9 - System testing
- Ch 10 - Installation inspection
- Ch 11 - Provisioning
- Ch 12 - Remote Client
- Ch 13 - Troubleshooting
- Ch 14 - Maintaining Quad T1 cards
- App A - Specifications
- App B - Standards compliance information
- App C - Part numbers
- App D - Updates and backups
- Index
1026209–0001 Revision B
Adding cards to the System Controller 2–17
Table 2-2 TX2000 card
I/O address settings (switch S1)
Address Setting Address Setting
8000 13 14 15 16 17 18 C000 13 14 15 16 17 __
8200 __ 14 15 16 17 18 C200 __ 14 15 16 17 __
8400 13 __ 15 16 17 18 C400 13 __ 15 16 17 __
8600 __ __ 15 16 17 18 C600 __ __ 15 16 17 __
8800 13 14 __ 16 17 18 C800 13 14 __ 16 17 __
8A00 __ 14 __ 16 17 18 CA00 __ 14 __ 16 17 __
8C00 13 __ __ 16 17 18 CC00 13 __ __ 16 17 __
8E00 __ __ __ 16 17 18 CE00 __ __ __ 16 17 __
9000 13 14 15 __ 17 18 D000 13 14 15 __ 17 __
9200 __ 14 15 __ 17 18 D200 __ 14 15 __ 17 __
9400 13 __ 15 __ 17 18 D400
1
13 __ 15 __ 17 __
9600 __ __ 15 __ 17 18 D600
2
__ __ 15 __ 17 __
9800 13 14 __ __ 17 18 D800 13 14 __ __ 17 __
9A00 __ 14 __ __ 17 18 DA00 __ 14 __ __ 17 __
9C00 13 __ __ __ 17 18 DC00 13 __ __ __ 17 __
9E00 __ __ __ __ 17 18 DE00 __ __ __ __ 17 __
A000 13 14 15 16 __ 18 E000 13 14 15 16 __ __
A200 __ 14 15 16 __ 18 E200 __ 14 15 16 __ __
A400 13 __ 15 16 __ 18 E400 13 __ 15 16 __ __
A600 __ __ 15 16 __ 18 E600 __ __ 15 16 __ __
A800 13 14 __ 16 __ 18 E800 13 14 __ 16 __ __
AA00 __ 14 __ 16 __ 18 EA00 __ 14 __ 16 __ __
AC00 13 __ __ 16 __ 18 EC00 13 __ __ 16 __ __
AE00 __ __ __ 16 __ 18 EE00 __ __ __ 16 __ __
B000 13 14 15 __ __ 18 F000 13 14 15 __ __ __
B200 __ 14 15 __ __ 18 F200 __ 14 15 __ __ __
B400 13 __ 15 __ __ 18 F400 13 __ 15 __ __ __
B600 __ __ 15 __ __ 18 F600 __ __ 15 __ __ __
B800 13 14 __ __ __ 18 F800 13 14 __ __ __ __
BA00 __ 14 __ __ __ 18 FA00 __ 14 __ __ __ __
BC00 13 __ __ __ __ 18 FC00 13 __ __ __ __ __
BE00 __ __ __ __ __ 18 FE00 __ __ __ __ __ __
1
Default for TX2000 IP (slot 16).
2
Use for TX2000 SS7 (slot 15).
Note: Underline ( __ ) indicates switch in OFF position.