Data Sheet

ManualsBrandsHUIYUAN ManualsLEDs & AccessoriesSMD LED 0805 Green 40 mcd 120 ° 20 mA

HUIYUAN OPTO-ELECTRONIC CO.,LTD.

TECHNOLOGY DATA SHEET & SPECIFICATIONS

MODEL：0805G6C-KPC-S

Page 1 of 6

Features

˙Compatible with automatic placement equipment

˙Compatible with infrared and vapor phase reflow solder process

˙Mono-color type

˙Pb-free

Descriptions

˙The 0805 SMD LED is much smaller than lead frame type components

thus enable smaller board size, higher packing density, reduced

storage space and finally smaller equipment to be obtained

˙Besides, lightweight makes them ideal for miniature applications.etc

Usage Notes:

˙Surge will damage the LED

˙When using LED, it must use a protective resistor in series with DC current about 20mA

Applications

˙Automotive: Backlighting in dashboard and switch

˙Telecommunication: Indicator and backlighting in telephone and fax

˙Flat backlight for LCD, switch and symbol

˙General use

Device Selection Guide

LED Part No.

Chip

Lens Color

Material Emitted Color

0805G6C-KPC-S AlGaInP Yellow Green Water clear

Summary of content (6 pages)

PAGE 1
HUIYUAN OPTO-ELECTRONIC CO.,LTD. TECHNOLOGY DATA SHEET & SPECIFICATIONS MODEL：0805G6C-KPC-S Features ˙Compatible with automatic placement equipment ˙Compatible with infrared and vapor phase reflow solder process ˙Mono-color type ˙Pb-free Descriptions ˙The 0805 SMD LED is much smaller than lead frame type components thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained ˙Besides, lightweight makes them ideal for miniature applications.
PAGE 2
HUIYUAN OPTO-ELECTRONIC CO.,LTD. TECHNOLOGY DATA SHEET & SPECIFICATIONS MODEL：0805G6C-KPC-S Package Dimensions Notes: ˙Other dimensions are in millimeters, tolerance is 0.25mm except being specified. ˙Protruded resin under flange is 1.5mm Max LED. ˙Bare copper alloy is exposed at tie-bar portion after cutting.
PAGE 3
HUIYUAN OPTO-ELECTRONIC CO.,LTD. TECHNOLOGY DATA SHEET & SPECIFICATIONS MODEL：0805G6C-KPC-S Electro-Optical Characteristics (Ta=25 ) Parameter Symbol Min. Typ. Max. Unit Test Condition Luminous Intensity Iv 30 --- 50 mcd IF=20mA(Note1) Viewing Angle 2θ1/2 --- 120 --- Deg (Note 2) Peak Emission Wavelength λp 565 --- 575 nm IF=20mA Spectral Line Half-Width △λ 15 20 25 nm IF=20mA Forward Voltage VF 1.9 --- 2.
PAGE 4
HUIYUAN OPTO-ELECTRONIC CO.,LTD. TECHNOLOGY DATA SHEET & SPECIFICATIONS MODEL：0805G6C-KPC-S Typical Electro-Optical Characteristics Curves Forward Current VS.Forward Voltage Relative Intensity VS. Wavelength 25 Forward Current (mA) Relative Intensity (a.u) 1.0 0.8 0.6 0.4 0.2 20 15 10 5 0 0.0 500 550 600 650 1.5 1.0 700 2.5 3.0 3.5 Forward Voltage (V) Wavelength (nm) Relative Intensity VS. Ambient Temp Forward Current VS.Relative Intensity 2.0 2.0 Relative Intensity (a.
PAGE 5
HUIYUAN OPTO-ELECTRONIC CO.,LTD. TECHNOLOGY DATA SHEET & SPECIFICATIONS MODEL：0805G6C-KPC-S Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big Current change (Burn out will happen) 2.
PAGE 6
HUIYUAN OPTO-ELECTRONIC CO.,LTD. TECHNOLOGY DATA SHEET & SPECIFICATIONS MODEL：0805G6C-KPC-S soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder 5. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing Notes 1.