Data Sheet

ManualsBrandsHUIYUAN ManualsLEDs & AccessoriesSMD LED 5050 Warm white 120 ° 20 mA

HUIYUAN OPTO-ELECTRONIC CO.,LTD

TECHNOLOGY DATA SHEET & SPECIFICATIONS

MODEL：5050SUW3C

Page 1 of 5

Features

˙InGaN White*3 Dice LED

˙Size：5.0mm×5.0mm×1.5mm

˙High luminous intensity, high reliability and long life

˙With ROHS Compliant

Descriptions

˙The 5050 SMD LED is much smaller than lead frame type components

thus enable smaller board size, higher packing density, reduced

storage space and finally smaller equipment to be obtained

˙Besides, lightweight makes them ideal for miniature applications.etc

Usage Notes:

˙Surge will damage the LED

˙When using LED, it must use a protective resistor in series with DC current about 50mA

Applications

˙Amusement equipment、

˙Information boards、

˙Flashlight for digital camera of cellular phone、

˙Lighting for small size device.

Device Selection Guide

LED Part No.

Chip

Lens Color

Material Emitted Color

5050SUW3C InGaN Warm White Water clear

Summary of content (5 pages)

PAGE 1
HUIYUAN OPTO-ELECTRONIC CO.,LTD TECHNOLOGY DATA SHEET & SPECIFICATIONS MODEL：5050SUW3C Features ˙InGaN White*3 Dice LED ˙Size：5.0mm×5.0mm×1.5mm ˙High luminous intensity, high reliability and long life ˙With ROHS Compliant Descriptions ˙The 5050 SMD LED is much smaller than lead frame type components thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained ˙Besides, lightweight makes them ideal for miniature applications.
PAGE 2
HUIYUAN OPTO-ELECTRONIC CO.,LTD TECHNOLOGY DATA SHEET & SPECIFICATIONS MODEL：5050SUW3C Package Dimensions Notes: ˙Other dimensions are in millimeters, tolerance is 0.25mm except being specified. ˙Protruded resin under flange is 1.5mm Max LED. ˙Bare copper alloy is exposed at tie-bar portion after cutting.
PAGE 3
HUIYUAN OPTO-ELECTRONIC CO.,LTD TECHNOLOGY DATA SHEET & SPECIFICATIONS MODEL：5050SUW3C Electro-Optical Characteristics (Ta=25 ) Parameter Symbol Min. Typ. Max. Unit Test Condition Luminous Intensity Iv --- 15 --- LM IF=50mA(Note1) Viewing Angle 2θ1/2 --- 120 --- Deg (Note 2) Color Temperature CT 3000 --- 4500 K IF=50mA Spectral Line Half-Width △λ --- 30 25 nm IF=50mA Forward Voltage VF 3.0 --- 3.4 V IF=50mA Reverse Current IR --- --- 50 µA VR=5V Note: 1.
PAGE 4
HUIYUAN OPTO-ELECTRONIC CO.,LTD TECHNOLOGY DATA SHEET & SPECIFICATIONS MODEL：5050SUW3C APPLICATION NOTES： 1)Soldering： ① Manual soldering by soldering iron： The use of a soldering iron of less than 25W is recommended and the temperature of the iron must be kept at no higher than 300 . ② Reflow soldering： a. The temperature profile as shown in Fig.3 is recommended for soldering SMD LED by the reflow furnace. b.
PAGE 5
HUIYUAN OPTO-ELECTRONIC CO.,LTD TECHNOLOGY DATA SHEET & SPECIFICATIONS MODEL：5050SUW3C ③ Ultrasonic：300W Max. 3) OTHERS： a. Care must be taken not to cause stress to the epoxy resin portion of SMD LED while it is exposed to the high temperature. b. Care must be taken not to the rub the epoxy resin portion of SMD LED with a hard or sharp edged article such as the sand blast and the metal hook as the epoxy resin is rather soft and liable to be damaged.