INSTA L L ATI O N I N ST R U C T I O N S
PA RT S R EQUIR ED Single QuickStand Parts A A (1) QuickStand Unit B (1) Base Plate C (1) Platform D (1) Palm Support E (1) VESA Plate F (6) M8 x 18 mm Flat Head Machine Screws G (4) M4 x 18 mm Pan Head Phillips H (4) M4 x 8 mm Pan Head Phillips I (4) VESA Spacer B D Additional Parts for Dual Monitor QuickStand J (1) Dual Monitor Crossbar K (1) M6 x 22 mm Flat Head Machine Screws L (2) M5 x 18 mm Flat Head Machine Screws M (2) VESA Plate N (8) M4 x 18 mm Pan Head Phillips O (8
WARNING Read all instructions carefully before installing this product or attempting to use it This product contains a loaded mechanism that is under tension. Do not attempt to remove or alter any part of this product or in any way modify or tamper with any component of this product other than as set forth in these instructions. Failure to comply with the instructions provided may result in property damage or serious injury.
ST EP 3 Attach Platform Tools: 6 mm Hex Key • Ensure the Platform is equally spaced from the Base Plate on either side (fig.
ST EP 6 Attaching QuickStand to the Work Surface IMPORTANT: Your QuickStand unit is heavy. If needed, please have assistance when lifting. • Carefully lift your QuickStand unit from its horizontal position to its vertical position (fig.
ST EP 8 Attaching Crossbar for Dual Monitors Tools: 3 mm Hex Key 4 mm Hex Key • Attach Dual Monitor Crossbar to QuickStand unit using the hardware kit supplied (fig. I) I ST EP 9 Attaching Dual Monitors Tools: #2 Phillips Screwdriver J • Make sure the top of the VESA Plates are facing towards the top of the monitor before securing • Screw down the VESA Plates using the hardware kit supplied (fig. J) • Slide each monitor into the quick-connector on the Dual Monitor Crossbar (fig.
ST EP 10 Secure Palm Support • Peel off sticker backing from Palm Support and place down in your desired position on the front edge of the Platform (fig. L) L ST EP 11 Attaching USB Devices Tools: Flat-Head Screwdriver • Using a Flat-Head Screwdriver if needed, remove cable cover by tilting out from the bottom (fig. M) • Route USB cables from keyboard and mouse into cable bracket (fig. N) • Carefully pull cable slack through bracket until cable heads are set within.
ST EP 12 Removing Brace Box • Remove tape and lift out box. (fig. Q) Q ADJUSTING QUICKSTAND In order to be able to raise and lower your QuickStand with ease, it is important to spend some time adjusting the tension adjuster which can be located in the top of the QuickStand unit ST EP 13 Adjusting Weight Capacity R WARNING: Do not use a Power Drill to adjust the tension adjuster Tools: 6 mm Hex Key • Remove top cover from QuickStand unit to expose the tension adjuster screw (fig.
ST EP 14 Adjusting Monitor Height SINGLE QUICKSTAND • Hold each side of your monitor and manually raise or lower until it is in the correct position (fig. T) T DUAL QUICKSTAND Tools: 6 mm Hex Key • Remove top cover of the carriage assembly (fig. V) • Slowly begin to turn the monitor height adjustment screw clockwise to raise the monitors and counter-clockwise to lower the monitors (fig.
ST EP 15 Adjusting Monitor Tilt +15º SINGLE AND DUAL QUICKSTAND • Hold the top and bottom of your monitor and manually adjust the monitor tilt until the desired angle is achieved (fig. X) X -5º ST EP 16 Adjusting Monitor Orientation SINGLE AND DUAL QUICKSTAND • Hold each side of your monitor and manually turn the monitor until the desired orientation of either landscape or portrait is achieved (fig.
HSQSI1114 Customer Service: N America +1 800 400 0625 / International +353 (0)1 858 0910 www.humanscale.
