HUMNO-F3FOXCI.
** Thank you for purchasing a HUMAX Digital Satellite Receiver. Please read this user manual carefully, to be able to safely install, use and maintain the product at maximum performance. Keep this user manual next to your product for future reference. Throughout the whole manual, Note indicates additional product operation information to make the user aware of possible problems and information of any importance to help the user understand, use and maintain the installation.
** The product has been manufactured to satisfy international safety standards. Please read the following safety precautions and warnings carefully. ** • • • • • • • • • • • GB 2 Disconnect the product from the mains before you start any maintenance or installation procedures. Do not overload a wall outlet, extension cord or adapter as this may result in electric fire or shock. The product should not be exposed to liquid of any kind.
** 1. Before Using the Product GB5 ** 1.1 Package Contents 1.2 Front Panel 1.3 Rear Panel 1.4 Conditional Access 1.5 Remote Control GB5 GB6 GB7 GB8 GB9 2. Setup GB11 ** 2.1 Connecting Antenna/TV/VCR 2.2 Connecting Audio System 2.3 Powering On GB11 GB12 GB13 3. Menu Map 4. Searching Services GB14 GB16 ** 4.1 Antenna Setting 4.2 Manual Search 4.3 Satellite Setting 4.4 Motor Limit Setting 4.5 USALS Setting 4.6 Automatic Search GB16 GB17 GB18 GB19 GB20 GB21 5. Basic Operation GB22 ** 5.
** 6. Service List GB25 ** 6.1 Switching Services 6.2 Organising Services 6.3 Organising Favourite Services 6.4 Organising Networks 6.5 Deleting Satellites GB25 GB26 GB27 GB28 GB29 7. Programme Guide 8. Setting Preferences GB30 GB32 ** 8.1 Parental Control 8.2 System Setting GB32 GB32 9. System Information GB34 ** 9.1 Status 9.2 Common Interface 9.3 Default Setting 10. Utility 11. Software Update 12. Troubleshooting 13. Specification 14.
** This chapter provides detailed instructions on the product and its accessories. 1.1 Package Contents When you unpack your package contents, make sure you have all the necessary items shown in the figure below. If any of the items are missing or damaged, please contact your product dealer for replacement. ** ** Remote Control ** Batteries ** User's Manual ** Scart Cable ** ** Note: The product image may differ from the actual product.
** 1.2 Front Panel ** ** 1. STANDBY Button Switches between Operation and Standby modes. ** ** 2. TV/RADIO Button Switches between TV and Radio. ** ** 3. CH-/CH+ Moves the TV/Radio service up/down. ** ** 4. TV LED Green light is emitted when the product is in TV mode. ** ** 5. RADIO LED Amber light is emitted when the product is in Radio mode. ** ** 6. STANDBY LED Red light is emitted when the product is in standby mode. 7. CI-MODULE SLOT A slot for a CI module with a Smartcard.
** 1.3 Rear Panel ** ** 1. LNB IN ** Connects to satellite antenna cable. ** 2. LNB OUT 6. VIDEO ** Connects to your TV or VCR and outputs Video signals. ** 7. AUDIO L/R ** ** Connects to other digital Set-Top Box. Connects to your TV or VCR and outputs Audio signals. ** 3. RS-232C ** 8. RF OUT ** ** Connects to your PC to update product’s software programme. Connects the RF signal of the product to the RF input jack on your TV. ** 4. TV SCART ** 9.
** 1.4 Conditional Access ** Inserting Common Interface CI-Module ** Your receiver is equipped with a slot for Common Interface (CI). ** 1. Open the right-hand flap on the front panel of the product. 2. Insert the Smartcard into the CI module, and CI module into the slot.
** 1.5 Remote Control 1. SOURCE ** Selects the input source between TV and the product. ** 2. TV/RADIO ** Switches between TV and Radio. ** 3. NUMERIC BUTTONS ** Enter a TV/Radio service number or menu option number. ** 4. MENU ** Displays the main menu. ** 5. TIME - WHITE ** Displays the current time on the screen. To set the current time, refer to 8.2 System Setting. ** 6. ARROW BUTTONS ** Changes services or moves the cursor up, down, left or right in menu option. ** 7.
** 9. CH - / CH + 17. ZOOM - BLUE ** ** Changes the service. Enlarges the picture. ** 10. RECALL ** 18. SUBTITLE - YELLOW ** ** Returns to the previous screen. Displays the subtitle language list where available. ** 11. FREEZE ** 19. V - / V + ** ** Freezes the TV screen you are watching. Does not cease audio. Adjusts the audio volume. ** ** 20. MUTE ** 12. WIDE Mutes or unmutes the audio temporarily. ** Changes the Display Format. ** ** 21. UHF ** 13.
** This chapter describes how to set up the product. Select the most appropriate procedure depending on your requirements. Before you connect the product to any other equipment, you must disconnect all equipments from their power sources. Note: If you encounter any problem when setting up the product, please contact your local product distributor. 2.1 Connecting Antenna/TV/VCR ** ** 1. Connect the Antenna to LNB IN of the product. 2. SCART cable or RCA cable is connected as in the figure above.
** 2.2 Connecting Audio System ** ** 1. Connect the optical S/PDIF terminal and Dolby Digital decoder to listen to higher quality sound.
** 2.3 Powering On ** 1. Connect the power cord of the product to a wall outlet. ** ** 2. Press the STANDBY button on the front of the product or the remote control.
** GB 14
** ** Menu structure varies according to an item and its operation. You can easily navigate the menu using the following instructions: ** 1. Press the MENU button to display the main menu screen. ** 2. Select the item you want using the button. ** 3. Press the OK button to move from a menu to a sub-menu. ** 4. Press the button to select option values. ** 5. Press the NUMERIC buttons to enter the option values. ** 6.
** When powering on your product for the first time after purchase, the Selecting Language screen is automatically displayed. Select your desired language using the button and press the OK button. Then the Antenna Setting menu will be displayed. The default PIN code is 0000. ** 4.1 Antenna Setting You can set antenna and LNB information to search services using Antenna Setting (MENU-INSTALLATION-SERVICE SEARCHING-ANTENNA SETTING).
** 4.2 Manual Search You can search services of the selected satellite by transponders if you know the transponder information. ** • • • • • • • • Antenna Alternative: Select antenna alternative which has different combinations of settings for search. Antenna Alternative 16 is predefined for SMATV. Frequency: Enter transponder frequency. Polarisation: Select the type of polarisation. Symbol Rate: Select or enter transponder symbol rate. FEC: Select FEC (Forward Error Correction).
** 4.3 Satellite Setting This menu appears only when you enable Motorised System in Antenna Setting menu and press the OK button while Antenna Alternative in Manual Search menu is selected. ** • • Satellite Name: Select a satellite to identify a motor antenna. If the desired satellite name is not listed, then select "OTHER". Movement: In user mode, this is used to fine-tune the position of the motor. In installer mode, this is used to search for the position of the satellite manually.
** To initialise the satellite position saved at Motor Antenna, set DiSEqC Command Mode to "Installer", set "Motor Control" to "Reset", then press the OK button. You will see a warning message. To continue the procedure, press the OK button. To set the motor position for each satellite manually, select the Satellite Name, set DiSEqC Command Mode to "Installer", and then set Movement to one option among "East", "Stop", or "West". The motor starts moving.
** 4.5 USALS Setting This menu appears only when you select "USALS" in Motorised System menu and press the i ** • • • Satellite Name: Displays the satellite list in name order. If the required satellite name is not listed, select "User Defined". You can enter the satellite name using the keyboard displayed on the screen. My Longitude: Enter the longitude. My Latitude: Enter the latitude. ** Note: The values for My Longitude and My Latitude will be saved after initial setting.
** 4.6 Automatic Search If you select the satellite to search services according to Antenna Setting, you can automatically search the service without entering any other information. To enter Automatic Search menu, press the MENU button, then select INSTALLATION-SERVICE SEARCHING-AUTOMATIC SEARCH. ** • Antenna Alternative: Select antenna alternative which has different combinations of settings for search. The Satellite Name is automatically displayed. Antenna Alternative 16 is predefined for SMATV.
** 5.1 Viewing Programme You can change a service using the CH-/CH+, , or NUMERIC buttons. You can also use the Service List or Programme Guide. You can adjust the audio volume using the V-/V+ or button. ** Programme Information (i-plate) i-plate, or the Information Box, is always displayed for a specific period of time whenever you switch services. You can view the programme information by pressing the i button while watching a programme.
** 5.2 Changing Language If the current programme provides subtitle information, the subtitle icon will appear on the i-plate. You can select the language for the subtitle using the SUBTITLE button. You can select a default subtitle language in MENU-INSTALLATION-SYSTEM SETTING-LANGUAGE SETTING-SUBTITLE LANGUAGE. If the current programme is available in multiple audio languages, you can select the language that you wish to listen in using the SOUNDTRACK button.
** 5.4 Setting Property of Service You can add the current service to Favourite group. In addition, you can lock, unlock, skip and delete the current service while watching a programme. The operation is as follows: 1. Press the OK button while watching a programme. The service list will appear on the screen. You can also display the service list using the MENU-SELECT SERVICE-SIMPLE (or ADVANCED).
** There are five types of service lists – All, Favourite, Network, Satellite, Alphabet - to find services you are interested in quickly and easily. All service list display all searched TV or Radio services sorted by service number. Favourite service list displays favourite services with automatic sub-groups and four sub-groups that you can organise services accordinig to your preference. Network service list displays services with several network subgroups.
** 6.2 Organising Services You can edit TV or Radio services using the Organise TV Services (MENU-INSTALLATION-SERVICE ORGANISING-ORGANISE TV SERVICES-ORGANISE ALL SERVICES) or Organise Radio Services (MENU-INSTALLATION-SERVICE ORGANISING-ORGANISE RADIO SERVICES-ORGANISE ALL SERVICES). You will be prompted to enter your PIN code. The default PIN code is 0000. Before leaving Organise TV/Radio Services screen, you will be prompted to save the changes.
** 6.3 Organising Favourite Services You can add services to Favourite groups using Organise Favourite TV Services (MENU-INSTALLATION-SERVICE ORGANISING-ORGANISE TV SERVICES-ORGANISE FAVOURITE A~D) or Organise Favourite Radio Services (MENU-INSTALLATION-SERVICE ORGANISING-ORGANISE RADIO SERVICES-ORGANISE FAVOURITE A~D). Before leaving Edit Favourite Services screen, you will be prompted to save the changes. If you would like to save the changes, select OK, and press the OK button.
** 6.4 Organising Networks You can delete, move and rename networks. To enter Organise Networks menu, go to MENU-INSTALLATION-SERVICE ORANISING-ORGANISE NETWORKS. You can select a network using the button, and press the COLOUR button to execute the corresponding operation as described on the screen. You can move the highlighter in order of Network List and Service List using the button. You can move the highlighter in reverse direction using the button.
** 6.5 Deleting Satellites You can delete satellites and transponders. To enter Delete Satellites menu, go to MENU-INSTALLATION-SERVICE ORGANISING-DELETE SATELLITES. The Delete Satellites screen consists of Satellite List on the left side of the screen and Transponder List and Service List on the right side. You can move the highlighter in order of Satellite List Transponder List, and Service List using the button. You can move the highlighter in reverse direction using the button.
** The programme guide provides the programme information for all services, based on date and time. In addition, it provides convenient ways to view programmes in "Now", "Next", "Weekly", or "Quick" mode - to search your desired programme and to watch or reserve it. You can go to the programme guide screen by just pressing the GUIDE button or by using MENU-TV GUIDE. To close the guide screen, press the GUIDE or EXIT button.
** • • • • Press the WHITE button to reserve the selected programme in Now, Next, Weekly, or Quick mode. Press the WHITE button to change the reservation mode or to cancel the reservation in Reserved mode. Select a service using the or CH-/CH+ button. When switching services using the button, press the OK button to display the selected service on the right side of the screen. Select a day in Weekly mode using the button, and press the OK button.
** This chapter describes the menu which lets you customise your product according to your perference. ** 8.1 Parental Control The Parental Control menu (MENU-PARENTAL CONTROL) lets you control the access to programmes by programme rating. Set Censorship Classification by age level. “No Block” allows you to watch programmes without any blocking. You can block all programmes regardless of age level. The blocked programmes require your PIN code. The default PIN code is 0000.
** 3. A/V Output Setting This menu lets you adjust the audio and video output, set Dolby Digital, match the screen ratio to your TV, select the display format according to the screen ratio, select the TV standard, and set the NTSC mode. You can choose the Dolby Digital audio stream whenever possible by selecting On in the Dolby Digital setting. 4. UHF Tuning You can select UHF Channels for your TV and adjust fine tuning setting. The channel range and frequency change according to PAL Standard. 5.
** 9.1 Status The Status menu (MENU-INSTALLATION-STATUS) provides checking tools such as status information of system and signal level of service. 1. STB Status You can view the information on the H/W and S/W version, device driver version, S/W last update, loaded version, system ID and current service. When you contact your service provider or local product distributor, this information may be required. 2. Signal Detection You can view the signal level and signal quality of the current service. 3.
** 9.2 Common Interface ** You can view the current status of the CI module. 9.3 Default Setting ** You can restore the product to the factory settings using the Default Setting menu (MENU-INSTALLATION-DEFAULT SETTING). You will be prompted to enter your PIN code. The default PIN code is 0000. After completing the default setting, the Searching Services screen will be displayed. For more information, refer to 4. Searching Services.
** The product provides various utilities; view calendar, check biorhythm, games. To use utilities, go to MENU-UTILITY. ** 1. Calendar You can see the specified monthly calendar. Press the button to change the year. Press the button to change the month. Press the OK or EXIT button to return to the previous menu. 2. Biorhythm You can adjust your birth year and date to see your current biorhythm status. Press the button to move to the next step. Press the button to change a value in the step.
** In order to maintain proper performance of the product, it is essential to have the most up-to-date software. ** 1. OTA (Over the Air) OTA, an abbreviation of Over–the-Air, is a standard for the transmission of software for equipment through a broadcast system. Over the Air (OTA) is simply an alternative method for downloading software versions. However, the operator reserves the right to decide when and where this software update can take place over the antenna.
** The product cannot work at all during software update. It may take 5-10 minutes to update software. Updating software is largely divided into two ways, automatic detection and using software update menu (MENU-INSTALLATION-STATUS-STB UPGRADE). New software can be found when powering on the product. The notice informing you of new software detection will appear on the screen. If you would like to update software, select Yes, and press the OK button.
** Before contacting your local service, please read the following instructions. If the product does not work normally after completing the following troubleshooting, please contact your local product distributor or service centre. ** 1. The LED on the front panel does not light. - Check the main power cable and make sure that it is plugged into a suitable power outlet. ** 2. No picture - Make sure that the product is in operation mode. - Make sure that the AV Cable is firmly connected to the TV.
** 5. Remote control does not operate - To manipulate the equipment with the remote control, its emitting part should directly point towards its receiving part of the product. - Check the battery of the remote control. ** 6. Reservation is unavailable - Check if it is not overlapped with other reservation. - Check if the power is off. ** 7. Watching scrambled service is not available - Install the proper CI module. - Check if the CI module is broken. - Pull out the CI module and reinsert.
** MPEG Transport Stream A/V Decoding Power Supply Aspect Ratio Video Resolution Audio Mode Input Voltage Type 4:3, 16:9 720 x 576, 720 x 480 Single /Dual mono/ Stereo /Joint stereo Power Consumption Memory Protection Flash Memory Graphics(MPEG) & System Memory EEPROM 2 Mbytes 16 Mbytes 8 Kbytes RF-Modulator Output Channel TV standard Preset Channel CH 21 ~ 69 PAL I/G/B/D/K CH 36 AC 90 ~ 250V, 50/60Hz Switching Mode Power Supply (SMPS) Operation mode: Max. 30 W Standby mode: Max.
** You can get information such as a troubleshooting guide, software upgrades and product support guide from the following web sites and call center (Hotline). Please try to contact to your local dealers first when facing a problem. ** Germany Tel: Opening Hours: E-mail: Website: Language: Australia 01805-778870 ( 0,12/min) Mon-Sat 8:00-20:00 techinfo@humax-digital.de www.humax-digital.de Deutsch/English/Turkish ** Italy 0870 247 8800 Mon-Fri 8:30-18:00 uksupport@humax-digital.co.uk www.humax-digital.
** Finland Tel: Opening Hours: Language: 09 56186366 Mon-Fri 8:00-16:00 Finnish/English ** Austria Tel: Opening Hours: E-mail: Website: Language: 0820 400675 ( 0,12/min) Mon-Sun 8:00-23:00 support@humax-digital.de www.humax-digital.de Deutsch/English/Turkish ** Note: For hardware repair, please visit our website.
