User's Manual

ManualsBrandsHumax ManualsElectronics11N Wireless Roaming Router

Internet

Electrical Outlet

T3 Router

T3 Extender

Gaming Console &

Media Sharing

Printer SharingStorage Sharing

Mobile Phone

Modem

WPS

Quick Start Guide

Wireless or Wired, it's smooh and seamless

AC1200 Dual Band Smart Wi-Fi Router

QUANTUM T3

1. Connecting the Internet

You can connect your product to the Internet over a direct WAN or through a modem.

1-1

If you access Internet by the modem such as ADSL, VDSL, cable and FTTH, plug one

end of the Ethernet cable to the Internet port of your product and the other end to the

LAN port of your modem.

1-2

If you access the Internet by WAN broadband, plug the Ethernet cable to the Internet

port of your product.

4. Connecting the Network Devices

You can connect your network devices to the router over wired or wirelessly.

Use Ethernet cables to connect your devices to the router over a wired Ethernet connection.

Note

: We recommend you to connect entertainment devices such as OTT, gaming console

and IPTV to the Entertainment ports. The ports have the priority in transmitting

multimedia data without transmission delay or interruption.

LEDs on the Front Panel

After the product is successfully registered on the network, the LEDs illuminate continuously to indicate

that the product is active and fully operational.

LED Operation

Power

White On Power is on.

O Power is o.

Internet

White On Internet is connected.

White Blinking Firmware update is in progress.

O Internet is not connected.

Wireless

White On Network is connected wirelessly.

White Slow Blinking WPS is in conguration. It may take 2 minutes.

White Fast Blinking WPS conguration is failed.

Blue On *Roaming & mesh network is congured through the Internet.

Blue Slow Blinking

*Roaming & mesh network is in conguration. It may take

2 minutes.

Blue Fast Blinking *Roaming & mesh network conguration is failed.

O Wi-Fi is not available.

Ethernet

White On Networking device is connected to the LAN port.

O No device is connected to the LAN port.

Internet, Wireless, Ethernet Blinking Resetting the system is in progress.

Note: Blue light is turned on when the roaming & mesh network is successfully configured over HUMAX

products.

Internet Connection

You can configure the network over a wired Ethernet connection or wirelessly.

Wired

Connect the Ethernet cable between the PC and the LAN port of your product.

Wireless

1. Open the web browser.

2. Enter http://dearmyrouter.net to the address bar, and then press the Enter key.

3. The default ID and password are admin and nnnn. nnnn is the last 4 digits of serial number.

Refer to the serial number at the bottom of your product.

Note: We recommend you to change the ID and password to secure your network.

Go to Management > Change Password to change your password.

Q-MODE

Your product supports Q-MODE that enables operating as a router or an extender.

It’s very simple to change the operation mode. Just slide the Q-MODE switch to ROUTER or EXTENDER.

Then, the mode change is automatically completed.

3. Powering On

1. Plug in the AC power adaptor from the power connector to an electrical outlet.

2. If the power successfully turns on, a white light on the power LED is turned on.

Note: Use only the AC power adaptor provided in this product. Using other

adaptors may damage the product.

3. Conguring WPS

You can configure WPS between the extender and the router.

3-1 Press the WPS buttons on both devices within 2 minutes. When WPS is

successfully configured, the blue light blinks on the Wireless LED.

Note: If you use another router other than HUMAX product, the white light blinks

on the Wireless LED, which means your extender is in repeater mode.

2. Powering On

2. Checking the Mode

Your product has the Q-MODE switch.

Check that the switch is set to ROUTER.

1. Changing the Mode

Your product has the Q-MODE switch.

Slide the switch to EXTENDER.

Warning

1. Connect all devices before you plug any power cords into the electrical outlet.

2. Always turn off the product and network devices before you connect or disconnect any cables.

3. Hazardous electrical voltages can exist on the product and peripheral devices and can be present on

any connected cables.

- With HUMAX QUANTUM Series,

you will experience seamless Wi-Fi network at any moment.

- T1, T2, T3, T3A, X1 and X3 support both roaming & mesh network, and T5, T7 and T9

support roaming network only.

- Roaming & mesh feature is conﬁgured over HUMAX products. (*)

BOTH

*Roaming Mode

*Mesh Mode

Scan the QR code

to access @@ on your mobile device.

Use it as Router

Use it as Extender

1-1

1-2

WPS

Extender has wireless connectivity

with a third party router

*Roaming & mesh network is configured

over HUMAX products

Router Mode

WISP Mode

AP Mode

Repeater Mode

Media Bridge Mode

3-2

Check the network when the connection is complete.

If you connect the extender to a HUMAX router, both network names are the same as if they

configure a single network. But, if you use a router other than HUMAX products, the network

name of your extender will copy the router›s name following Ext2G or Ext5G.

(ex. Router_Ext5G)

Welcome to QUANTUM T3!

http://dearmyrouter.net

192.168.1.1

admin

****

Password

! For the default ID and password, see the bottom of the product.

ROUTER

EXTENDER

Humax Co.,Ltd.

HUMAX BLDG., 2, Yeongmun-ro,

Cheoin-gu, Yongin-si, Gyeonggi

-do,449-934,South Korea

Trade Name/Mark: xxxxxx

Full Postal Address: xxxxxx

Router Login:

http://dearmyrouter.net

ID: admin

Password: nnnn

S/N: QT3YYWWnnnnnn

Mac: DCDC8321000001

FCC ID: O6ZT3

Model: QUANTUM T3 Code: 4-00023

2.4G/5G SSID: We Love You So Much

Password: humax_nnnn

211-170615

D170027211

Barcode

Power Input: 12V 1.5A

※ Please change Login Password and Wi-Fi Password for Security.

Humax Co.,Ltd.

HUMAX BLDG., 2, Yeongmun-ro,

Cheoin-gu, Yongin-si, Gyeonggi

-do,449-934,South Korea

Trade Name/Mark: xxxxxx

Full Postal Address: xxxxxx

Router Login:

http://dearmyrouter.net

ID: admin

Password: nnnn

S/N: QT3YYWWnnnnnn

Mac: DCDC8321000001

FCC ID: O6ZT3

Model: QUANTUM T3 Code: 4-00023

2.4G/5G SSID: We Love You So Much

Password: humax_nnnn

211-170615

D170027211

Barcode

Power Input: 12V 1.5A

※Please change Login Password and Wi-Fi Password for Security.

Summary of content (2 pages)

PAGE 1
Use it as Router LEDs on the Front Panel Warning After the product is successfully registered on the network, the LEDs illuminate continuously to indicate that the product is active and fully operational. 1. Connect all devices before you plug any power cords into the electrical outlet. Quick Start Guide Electrical Outlet LED 2. Always turn off the product and network devices before you connect or disconnect any cables. 3. Powering On 1.
PAGE 2
Network Configuration on Web Page When you log in to the router for the first time, the installation wizard will appear. Then, follow the steps to configure the network. 3. Wireless Network Setting Router Mode Enter your own network name and password to change the default settings. You can secure your wireless network from unauthorized users. 1. Welcome Wireless Setting Click Start. The system will check automatically if your router is connected to the Internet. WISP Mode 2-1.