GLINT 2.
GLINT 2.0 GLINT 2.0 has the function of one-key takeoff, landing, return to home, follow me, point of interest, point flying and waypoints. The GLINT 2.0’s camera records videos at up to 4K/1080P and captures 16-megapixel photos stably during flight. Review the diagram below for a full list of your GLINT 2.0’s parts: 1. Camera 2. 3-axis Gimbal 3. Gimbal Fixed Screw 4. Micro-USB Port 5. Landing Gear 6. Handle 7. Motor 8. Propeller 9. Intelligent Flight Battery 10. Power Button (LED fight indicator) 11.
Remote Controller This powerful Remote Controller allows you to pilot and maneuver your GLINT 2.0 at distances over 1km *away, while putting selected camera controls at your fingertips. Built-in your Remote Controller is a chargeable LiPo battery, which can work last for 8 hours*.
Specification Aircraft l Weight 1.5~2.5kg Total Weight 1.9kg Power Battery 4S/6500 mAh/10C Max. Ascent Speed 5m/s Max. Descend Speed 2m/s Max. Level Speed 6m/s(GPS) Max.
Battery 2S 6000 mAh Operating Current/Voltage 500mA/7.4V l Aircraft Charger Voltage/Current Power Rating l 17.4V /3A 60W Remote Controller Charger Voltage/Current 8V/ 1A Power Rating 12W l Intelligent flight battery Type Li-Po 4S Capacity 6500 mAh Voltage 15.2V Energy 98.
Use your GLINT 2.0 Before using GLINT 2.0, please visit the product page on Keyshare official website to view the whole tutorial videos and download GLINT2 User Manuals，and read the following files carefully: GLINT 2.0 Quick Start Guide, GLINT 2.0 Disclaimer Operation and Safety Manual, GLINT 2.0 Smart Battery Safety Instructions and List of Articles. 1. Download GLINT 2.0 APP 2. Watch the Tutorial Videos Search ‘GLINT 2.0 APP’ on the APP Store and Watch the Tutorial Videos on www.key-share.
Remove the Intelligent Flight Battery l Please use the official charger that provided by Keyshare. Remove the intelligent flight battery from aircraft before charging. l Connect the intelligent flight battery charger to the AC power supply (100-240V, 50-60Hz; if required, please use the power adapter). Connect the charger to the remote controller. If the charger LED of remote controller is red, the charger is working.
GLINT2_×××××× from your Wi-Fi list. Input the default connection password: 12345678. 3. Start GLINT 2.0 APP, tap “connect” button to enter into the home page. If you can enter into the home page after connection, it means that the remote control and mobile device connect successfully. Otherwise it means the failure connection. Warning Make sure that the aircraft doesn’t unlocked to take off before using GLINT 2.0 APP. *To avoid signal interference, don’t use other 2.4GHz device when flying. 6.
1. Toggle the flight mode switch on your remote controller to the P mode. (P mode is positioning mode; A mode is ALTHold mode, and F mode is function mode). 2. Turn on the remote controller. 3. Turn on the intelligent flight battery. 4. Ensure that the remote controller has connected to the aircraft. (The flight battery indicator on remote controller displays the battery power normally, indicating the connection is successful. ) 5.
motors start. Push the throttle stick (default American Hand) up over midpoint to takeoff. Landing Pull the throttle stick down until the aircraft touches the ground. There are two ways to stop the motor. First, after landing, the motors of aircraft are in idle status, if no operation within 3 second, the motors will automatically lock. Second, after landing, the motor will stop immediately if you execute Combination Stick Command.
FCC Caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
