Lift Accessories For Hunter Wheel Alignment Lift Racks
Fully Integrated Alignment Hunter lifts with FIA capabilites streamline the entire alignment process. Direct communication between the lift and aligner automate tasks once performed by the technician manually, eliminating time-consuming trips around the vehicle and to-and-from the console.
WinAlign® console* ✔ Centralized control of entire system ✔ Communicates directly with lift to set tire pressure and automatically operate turnplates and slipplates Cameras capture measurements automatically once the fourth target is installed ✔ Guides the technician through the alignment process ✔ Rack Track auto-adjusts electronic movable-camera sensors to match lift height* Lift console ✔ Raising the vehicle triggers the sensors to look for wheel targets* ✔ Controls PowerSlide ® and Inflation Stat
RX-series & Four-Post lift family PowerSlide system ® The PowerSlide® system secures and releases slipplates and turnplates with one touch. With the PowerSlide system, technicians no longer have to make multiple trips around the vehicle or struggle to remove and replace lock pins during an alignment. PowerSlide Turnplates PowerSlide Slipplates See page 7 for PowerSlide turnplate options.
Inflation Station system RX-series & Four-Post lift family The Inflation Station system inflates all four tires to a pre-selected pressure simultaneaously - while you raise the lift or do other tasks! Saves steps and save time! RX Lift Inflation Station control panel Four-Post Lift Inflation Station/FIA console ✔ Set tire pressure at the lift console or at the aligner* ✔ Automatically inflate all four tires simultaneously ✔ Record starting and final pressure** Integrated inflation hoses, located at ea
AlignLights The AlignLights system provides a safe and efficient light source underneath the vehicle without additional electrical cords. The lights automatically switch on when the lift is raised and off when the lift is lowered. ✔ For all old-style RX consoles (power unit exposed) – 20-2013-1 ✔ For RX Inflation Station and other new-style lift consoles – 20-2173-1 ✔ For L451 and L454 lifts – 20-2993-1 AlignLights is an ALI listed accessory for all lift models.
9,000-lb. Capacity, Triple Composite Cylinder Jack – 133-84-1 Ideal for use with RX16, L451 and L454 lift models. 6,000-lb. Capacity, Dual Composite Cylinder Jack – 133-85-1 Ideal for use with RX-10 and RX12A lift models. Turnplates ® PowerSlide Turnplates PowerSlide® turnplates eliminate the hassle of removing and replacing lock pins during an alignment. Integrated bridges lower and raise as plates are locked.
Turnplates cont. Stainless Steel Turnplates Resists corrosion and maintains free movement during the alignment procedure. Stainless steel construction for long, trouble-free life. No pointer. Stainless Steel: ✔ Set of two stainless steel turnplates for 1.
Turning Angle Gauge – 25-18-1 Turnplate with pointer and scale for 1.5" turnplate pocket. Steel construction with a powder-coated paint finish (two required). Filler Plates Fills turnplate pockets when turnplates are not used. 19.5" wide. ✔ For 1.5" pockets – 20-2396-1 (two included) ✔ For 50 mm pockets – 20-2395-1 (two included) Turnplate Bridge Eases rolling compensation when rack is used with camera-based alignment sensors. ✔ Universal Bridge for 50 mm and 1.
Ramps & extensions High-floor-slope conditions and low-ground-clearance vehicles occasionally require additional approach ramp length. Several options are available. Stage 2 RX Approach Ramp Extensions ✔ RX ramp extension kit – 20-3113-1 (two included) Adds 17.75" to the length of RX9, RX10 and RX16; or 5" to RX-12 and RX12A when substituted for 20-3112-1. Standard on RXDC. ✔ RX ramp extension kit – 20-3112-1 (two included) 12" extensions for RX10, RX12 and RX16. Standard on RX-12 and RX12A.
Additional lift accessories Pit Hose Reel Cover Plate – 51-2308-1 Cover plate for Inflation Station lifts to trim around flush-mount cut-outs (four required). L421 Runway Extension Kit – 20-1587-1 Extends maximum general service wheelbase to 226.5" and maximum two-wheel alignment wheelbase to 210.5". Includes two 19.5" filler plates. Front-Mount Power Unit Bracket Moves power unit mounting to front of four-post column for bays with very little space.
Additional lift accessories Jack Pad – 64-50-2 Rubber pads cover jack lifting points to prevent damage to the underside of the vehicle (two required). Wheel Chock – 22-525-2 Prevents vehicle from rolling once on the lift. Two chocks are included standard in any new lift purchase. Storage Bracket Kit 20-2528-1 Provides storage for wheel adaptors on console, lift or HawkEye Elite® sensor column. Simply bolts on to clip-on work step holes, no drilling required. Includes four brackets.
