Wheel Balancer Accessories
Wheel mounting kits & accessories Why use collets? Precise wheel balancing relies on two critical conditions: accurate center mounting and distortion-free clamping while providing wheel protection. The center of the wheel must be properly located on the balancer shaft. Hubcentric and lug-centric wheels all use the hub bore as the center locating position of the wheel. The hub bore centerline is virtually the same as the lug holes.
Premium BullsEye® collet kits Hunter's BullsEye® kits provide comprehensive coverage for passenger-car and light-truck wheels, including 1-ton capacity. Features optional centering and wheel protection over basic cone and collet sets. BullsEye collets and storage are standard on Road Force Touch balancers. 20-2683-1 – BullsEye® collet set Kit includes: A. 192-213-1 B. 192-214-1 C. 192-215-1 D. 192-216-1 E. 192-217-1 F. 192-218-1 G. 192-219-1 H. 192-220-1 I. 192-221-1 J. 192-222-1 A Cone: 2.10 in. to 2.
Touch / LCD series wheel balancers Standard balancer accessories 20-2145-1 – Basic Touch / LCD accessory kit Kit includes: A. 106-82-2 B. 175-353-1 C. 76-433-3 D. 221-658-2 E. 46-320-2 F. 221-589-2 G. 223-68-1 H. 20-1650-1 I. 221-659-2 J. 65-72-2 K. 233-44-2 Sleeve, scratch guard for small cup Polymer cup (4.5 in. O.D.
Flange plates & stud kits 20-1839-1 – Adjustable flange plate & stud kit The preferred recommendation when choosing a flange plate kit for maximum application coverage. Single-plate sliding bolt circle design with interchangeable pins provides quick setup and universal fitment. The kit adapts to 3-, 4-, 5-, 6-, 7- and 8-lug bolt circles with infinite adjustability. Fits future vehicle bolt circles that have yet to be released. The maximum bolt circle diameter is 6.70 in. (170 mm) and minimum diameter is 3.
Wing nuts 76-433-3 – High-torque steel wing nut 76-432-1 – Steel wing nut Forged steel wing nut with handles and bearing kit. Standard for RFT, SWT, RF, SW and FM balancers. Forged steel wing nut with no handles. Standard for DSP9200 and DSP7700 balancers. 76-438-2 – QuickNut steel wing nut Collapsing jaws allow fast clamping to standard threaded 40 mm shafts on most DSP and LCD series wheel balancers.
Cups, pressure rings & spacers continued... 106-82-2 – Protector sleeve 106-157-2 – Protector sleeve 175-392-1 – Cup 46-309-2 Extra large truck cone wheel spacer Fits all 4.5 in. cups to protect finished wheel surfaces when using a cup to clamp. Fits all 6 in. cups to protect finished wheel surfaces when using a cup to clamp. 6 in. clamping cup fits aluminum wing nut (76-390-1), forged steel wing nuts (76-4321 and 76-433-3), QuickNut (76-438-2), and AutoClamp feature. 175-324-1 A B (8.00 in. O.D.
Cups, pressure rings & spacers continued... 223-68-1 – Pressure ring Fits both aluminum DSP and GSP wing nuts. Prevents metalto-metal contact, significantly increasing clamping force (height: 0.97 in.). 76-379-2 – Threaded shaft ring Prevents cone or collet from sliding off the balancer shaft when removing assembly from the balancer. Not recommended unless same cone is used repeatedly.
Optional accessories continued... NEW! 221-672-1 Optional calibration tool For load roller and Dataset® arms. 20-3101-1 – Hunter wheel lift system Wheel lift system helps technicians safely service today’s oversized, light-truck and medium-duty wheels. Compliant platform permits easy alignment and improves centering. OE Special Applications 192-152-2 192-165-2 – Cone (BMW-special) Low-taper two-step design 2.783 in. - 2.913 in. (71 mm-74 mm) 2.200 in. - 2.279 in.
MD balancer accessories Basic cone kit 20-1207-1 – Large truck cone & spacer kit Used when mounting single or dual truck wheels such as the Ford and GM 19.5 in. Accuride wheel. 20-1207-1 A B Kit includes: A. 46-309-2 Wheel spacer 8.00 in. O.D. x 6.30 in. I.D. x 1.53 in. (127 mm-168 mm) [See page 7 for details.] B. 192-92-2 Extra large truck cone 5 to 6.63 in. and 6.68 in. to 6.94 in. (170 mm-176 mm) used for extra large light trucks and motor homes.
HD balancer accessories 20-2274-2 – Truck / bus adaptor kit Kit includes: A. 175-396-2 175-394-2 76-463-2 B. 175-393-2 C. 175-397-2 D. 175-420-2 E. 192-182-2 F. 192-181-2 Adaptor - 5 arm clamp star Pin HD steel (5) Nut - knurled HD M16 (5) Adaptor - wheel support HD Adaptor - 4 arm clamp star MD Pin HD steel (5) Cone - HD 219.9 mm Cone - HD 220.8 mm Not shown: 74-418-2 SHCS - 3/8 - 16 X 2.
HD balancer accessories continued... 20-1602-1 B A C 20-1602-1 TruckChuck wheel and drum balancing kit* Three-jaw chuck adaptor for factory steel and some aluminum wheels with centering holes from 3.13 in. to 7.13 in. Kit includes: A. 175-286-2 Three-jaw chuck adaptor Shown with 20-1603-2 jaw kit. B. 20-1854-2 Heavy-duty extended jaw kit For wheels with centering holes from 5.13 in. to 9.13 in. The TruckChuck balancing kit is used on the mounting pad side of medium-duty and lighttruck wheels. C.