www.HunterFan.com Table of Contents What to Expect with Your Installation Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. Ceiling Plate Tools Needed 1.888.830.
www.HunterFan.com What to Expect with Your Installation 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box 7 feet from bottom edge of blade to the floor Know your wiring Assess location You may need a friend to help you.
www.HunterFan.com Tools Needed Ladder Pliers Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M0115-01 • 02/11/16 • © 2016 Hunter Fan Company Screwdrivers 1.888.830.
www.HunterFan.com Ceiling Plate 1.888.830.1326 Bumper r we o nP r Tu OFF Make sure all four bumpers are still attached. Use wood screws (included) when securing to support structure with approved electrical outlet box. Drill 9/64” pilot holes in support structure to aid in securing ceiling plate with hardware found in the hardware bag.
Top Housing www.HunterFan.com 1.888.830.1326 Top Housing Canopy Trim Ring Adapter Adapter Thread the wires through the top housing. Place the top housing onto the motor housing so that the holes in the top housing lineup with the holes in the motor housing and the adapter. Rest the trim ring on the top housing. 5 M0115-01 • 02/11/16 • © 2016 Hunter Fan Company Place the canopy on the top housing. Ensure all four screw holes line up with the screw holes in both the top housing and the adapter.
www.HunterFan.com STRIP CUT Top Housing (continued) Top Housing Screws (not to scale) 8” & 3/8” Grounding Screw Install the top housing screws. Install the grounding screw in the smaller screw hole. These screws can be found in the hardware bag. The wires can be cut, but leave at least 8” extending from the top of the canopy. 8” 3/8” 6 M0115-01 • 02/11/16 • © 2016 Hunter Fan Company 1.888.830.
www.HunterFan.com Hanging the Fan Ceiling Plate Hook Ceiling Plate Hook Raise the fan and align the slots in the canopy with the hooks on the ceiling plate. Note: To hang the fan, you must tilt the canopy to an almost vertical position so that the canopy slots sit on the ceiling plate hooks. Place the slots over the ceiling plate hooks to hang the fan. Note: Fan style may vary. 7 M0115-01 • 02/11/16 • © 2016 Hunter Fan Company 1.888.830.
Wiring Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. www.HunterFan.com OM FR G green/yellow stripe (grounding) Receiver CEILIN 1.888.830.1326 green Using an orange wire connector from the hardware bag, connect the 3 grounding wires (green, green/ yellow stripe, or bare copper) coming from the ceiling and ceiling plate.
www.HunterFan.com OM FR OM CEILING FR • Connect the blue wire from the receiver to the blue wire (or possibly black with white stripe wire) from the fan. • Connect the white (grounded) wire from the ceiling to both the white wire from the receiver and the white wire from the fan. FRO white FR M FA N OM FAN FR OM white Connect the black (ungrounded) wire from the ceiling to the black wire from the receiver.
www.HunterFan.com Canopy 1.888.830.1326 Ceiling Plate Hooks Canopy Screw Canopy Screw Screw Holes Swing the fan up to align the canopy screw holes with the mounting holes on the ceiling plate. Note: The slots in the canopy must remain engaged while swinging the canopy for alignment. Hold the canopy up with the screw holes aligned. Partially install two canopy screws, found in the hardware bag, into the holes opposite the ceiling plate hooks.
www.HunterFan.com Canopy (continued) Canopy Trim Ring Using both hands, push the canopy trim ring up to the top of the canopy. The canopy trim ring will snap and lock into place. Note: Should you need to remove the trim ring, press firmly on opposite sides of the trim ring. The tabs will flex out releasing the canopy trim ring. 11 M0115-01 • 02/11/16 • © 2016 Hunter Fan Company 1.888.830.
Blades www.HunterFan.com Attach each blade to a blade iron using three blade washers, found in the hardware bag, and three blade assembly screws, found in the hardware bag. 12 M0115-01 • 02/11/16 • © 2016 Hunter Fan Company 1.888.830.
Switch Housing Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. www.HunterFan.com Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. 13 M0115-01 • 02/11/16 • © 2016 Hunter Fan Company 1.888.830.1326 Insert the third screw, found in the hardware bag, into place and then tighten all three screws.
www.HunterFan.com Light Kit Screw two housing assembly screws from the hardware bag halfway into the upper switch housing. It does not matter which two screw holes you choose. Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors.Wrap light kit keyhole slots around the screws and twist counterclockwise. 14 M0115-01 • 02/11/16 • © 2016 Hunter Fan Company 1.888.830.1326 Install the third switch housing screw.
www.HunterFan.com Light Kit (continued) Tab Notch Install a bulb into each of the sockets. When necessary, replace with bulbs of the same type and wattage. Lift the globe and align the notches in the globe with the tabs in the light kit. Attach the glass bowl to the light kit by twisting it clockwise until it snaps into place. 15 M0115-01 • 02/11/16 • © 2016 Hunter Fan Company 1.888.830.
www.HunterFan.com Remote Control Switch Cover Plate 1.888.830.1326 r Tu er ow P n ON Battery Door Phillips Head Screw To access the battery compartment, remove the small Phillips head screw that secures the battery door to the transmitter assembly. The battery should be installed with the positive (+) side up. Replace with a CR2032 battery when necessary. Removed Tabs Rocker- Style Plate To install the transmitter cradle, remove the two screws holding the switch cover plate.
Operation, Maintenance, & Cleaning www.HunterFan.com 1.888.830.1326 Medium Speed Fan Off Low Speed High Speed Light To turn on fan, press a fan speed button. Speeds range from off (0) to high (3). Quickly press the Light button to turn the lights off and on. Hold the Light button to raise and dim the light level. Reverse Switch The remote transmitter should already be paired to the receiver and ready to use. Note: If your need to pair your remote, turn fan power off and back on at the wall switch.
Operation, Maintenance, & Cleaning (continued) www.HunterFan.com 1.888.830.1326 Safe-Exit The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off to exit the room before the lights go out. To use Safe-Exit: • Press the Fan Off button for at least three seconds to initiate the Safe-Exit Mode. • The lights will flash for visual confirmation. • The lights will stay on 50% brightness for 15 seconds and then begin to dim.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely.