www.HunterFan.com Table of Contents What to Expect with Your Installation 30 inches Downrod Ladder 3 Wiring Maintenance, Operation & Cleaning Light Kit 12 ? ? ? 17 PA G E 16 Troubleshooting PA G E M3642-01 • 01/06/17 • © 2017 Hunter Fan Company PA G E 13 1 11 PA G E 9 5 Blade Canopy PA G E 6 4 PA G E 2 PA G E 7 feet PA G E Save your receipt for proof of purchase. Ceiling Bracket PA G E To register your fan, please visit: www.HunterFan.
www.HunterFan.com What to Expect with Your Installation 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. WARNINGS If you are unfamiliar with wiring, use a qualified electrician. 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring You may need a friend to help you. Ceiling angles greater than 34° will require an Angled Mounting Kit. See page 4 for details.
www.HunterFan.com Tools Needed Ladder Screwdrivers Pliers 1.888.830.1326 Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M3642-01 • 01/06/17 • © 2017 Hunter Fan Company Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag. The symbols can be used to identify the appropriate hardware for each step.
34O CEILING www.HunterFan.com Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
www.HunterFan.com Ceiling Bracket 1.888.830.1326 For angled ceilings, point opening toward peak. er w o nP r Tu OFF Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
www.HunterFan.com Option 1 Downrod 1.888.830.
www.HunterFan.com KEEP! (not to scale) 8” & 3/8” 1.888.830.1326 STRIP CUT Downrod (continued) ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
www.HunterFan.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Note: Fan style may vary. 8 M3642-01 • 01/06/17 • © 2017 Hunter Fan Company 1.888.830.
Wiring: Single Switch www.HunterFan.com 1.888.830.1326 Dual Switch Instructions Have a single switch? Follow these steps: gro Un Grounded White ou nd ing i pe Str Gr Blue Connect the black wire (ungrounded) from the ceiling to the black and the blue wires from the fan. ellow Green/Y Connect the white (grounded) wire from the ceiling to the white wire from the fan.
Wiring: Dual Switch www.HunterFan.com 1.888.830.1326 Have dual switches? Follow these steps: Grounded ellow Green/Y Grounded White Gr ou Ungrounded (lig ht) Black ing rou nd ed Green/Yellow Stripe Connect the three grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket. Un g Connect the black wire (ungrounded) from the ceiling to the black wire from the fan.
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 11 M3642-01 • 01/06/17 • © 2017 Hunter Fan Company 1.888.830.
Blades www.HunterFan.com Put each blade washer, found in the hardware bag, onto a blade screw, found in the hardware bag. Then secure each blade to a blade iron using the blade screws and washers. 12 M3642-01 • 01/06/17 • © 2017 Hunter Fan Company 1.888.830.
Light Kit www.HunterFan.com Partially install two light kit assembly screws, found in the hardware bag, halfway into the motor housing as shown. It does not matter which two screw holes you choose. Feed the 9-pin plug connector coming from the bottom of the motor housing through the center hole in the light kit assembly. Connect it to the plug connector found in the switch housing area of the light kit assembly. Make sure to line up the colored markings on the connectors.
www.HunterFan.com Light Kit (continued) Insert a third light kit assembly screw, found in the hardware bag, into place and tighten all three screws securely. Make sure the light kit assembly is securely attached to the motor housing. Failure to properly secure all three assembly screws could result in the light fixture falling. Carefully push all switch housing components into the switch housing, then install the switch housing plate using two light kit assembly screws, found in the hardware bag.
www.HunterFan.com Light Kit (continued) 1.888.830.1326 Tab CONGRA T YOU’REULATIONS! DONE! Notch Align the notches in the outer rim of the globe with the tabs on the light kit assembly Carefully lift the globe up inside the light fixture as far as it will go. Rotate the globe in a clockwise direction until it is held tightly in place by the three tabs. Remove and discard the plastic connectors from the ends of the short pull chain.
Maintenance, Operation, & Cleaning www.HunterFan.com 1.888.830.1326 r Tu er w o nP ON Reverse Switch Changing the bulbs - carefully remove the globe. Unscrew the bulbs and replace them with bulbs of the same wattage. Reinstall the globe. Changing the direction of air flow - carefully remove the globe and move the reverse switch to the opposite position. Reinstall the globe. 16 M3642-01 • 01/06/17 • © 2017 Hunter Fan Company Cleaning the fan - use soft brushes or cloths to prevent scratching.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check to see if any of the blades are cracked. If so, replace all of the blades.