4-Light Fitter With Glass Installation Manual Models 99093, 99094 Compatible with: 51000-58999 fan series 59500-59999 fan series Select Casablanca Fans MA008-01 • 08/17/15
1.888.830.1326 BEFORE YOU BEGIN Read entire installation instructions carefully before beginning installation and save these instructions. Switch Housing Your light kit is compatible with most ceiling fans. The light kit will attach to the fan’s switch housing. Begin on page 3 where you will choose the type of switch housing that most closely resembles the one on your fan. From there, you will be directed to the set of assembly instructions that are appropriate for installing the light kit to your fan.
1.888.830.1326 WHICH ASSEMBLY METHOD WILL I USE? Choose one of the four images below that most closely resembles the switch housing on your fan; then follow the instructions under the image. Cap Screw Switch Housing Screw Switch Housing Cap If your fan’s switch housing cap resembles this one, remove the cap screws with a Phillips head screwdriver. Then follow the TYPE-A ASSEMBLY INSTRUCTIONS on pages 4-5.
1.888.830.1326 TYPE-A ASSEMBLY INSTRUCTIONS 1 2 Light Kit Screw Switch Housing Wire Harness Remove the pre-installed light kit screws and replace them with the longer light kit screws provided. Wire Connector If your fan does not have pin connectors on the wires coming from the switch housing, install the wiring harness provided.
1.888.830.1326 TYPE-A ASSEMBLY INSTRUCTIONS (CONTINUED) 5 6 Thumb Screw Shade Installing the shade - First loosen the thumb screws. Raise the shade to the light fixture. Tighten all thumbscrews securely. Installing the bulb - Install a bulb into each socket. When necessary, replace bulbs with bulbs of same type and wattage. 7 8 er ow P n Tur ON Installing the pull chain pendant Attach the pull chain pendant to the end of the short chains coming from the switch housing and the light kit.
1.888.830.1326 TYPE-B ASSEMBLY INSTRUCTIONS 1 2 Switch Housing Wire Harness Washer and Nut Switch Housing Wire Connector If your fan does not have pin connectors on the wires coming from the switch housing, install the wiring harness provided. Using the provided wire connectors connect the white wire from the fan to the white wire from the wire harness and connect the black or blue wire from the fan to the black wire from the wire harness.
1.888.830.1326 TYPE-B ASSEMBLY INSTRUCTIONS (CONTINUED) 5 6 Thumb Screw Shade Shade Installing the shade - First loosen the thumb screws. Raise the shade to the light fixture. Tighten all thumbscrews securely. Installing the bulb - Install a bulb into each socket. When necessary, replace bulbs with bulbs of same type and wattage. 7 8 er ow P rn Tu Installing the pull chain pendant Attach the pull chain pendant to the end of the short chains coming from the switch housing and the light kit.
1.888.830.1326 TYPE-C ASSEMBLY INSTRUCTIONS 1a 1b OR Switch Housing Pin Connectors If your fan does not have pin connectors on the wires coming from the switch housing, go to step 2. If the fan has pin connectors, cut the wires just above the fan pin connectors with wire cutters. Discard the pin connectors. Go to step 2.
1.888.830.1326 TYPE-C ASSEMBLY INSTRUCTIONS (CONTINUED) 4 5 6 Upper Switch Housing Using the single pin connectors, connect the black or blue wire from the fan to the black wire from the light kit. Connect the white wire from the fan to the white wire from the light kit. 7 Thumb Screw Shade Lift the light kit assembly up so that the screw holes in the lower switch housing line up with the holes in the upper switch housing. Install the switch housing screws and tighten securely.
1.888.830.1326 TROUBLESHOOTING Lights don’t come on. • Make sure the bulbs are properly installed. • Make sure the power switch is on. • Pull the light pull chain to make sure it is on. • Check the circuit breaker to ensure the power is turned on. • Check the pin connections in the light kit. • Refer to the fan manual for locating the fan’s wiring instructions. Verify that the wiring is connected correctly.
