© 2003 Hunter Fan Company 41854-01 11/12/2003
® Your new Hunter® ceiling fan is an addition to your home or office that will provide comfort and performance for many years. This installation and operation manual gives you complete instructions for installing and operating your fan. We are proud of our work. We appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world. Before installing your fan, record the following information for your records and warranty assistance.
Angle Mounting (Figure 2) hangs from a vaulted or angled ceiling. using an existing fan site If you are preparing a new fan site, go to the p rep arin ingg a n neew ffaan sitte section. si If you plan to use an existing fan site, complete the following checklist for the support brace, ceiling hole, outlet box, and wiring. If you ingg a n nee w ffaan si sitte seccannot check off every item, see the prep ar in tion for instructions on properly preparing the site for your new fan.
cutting the ceiling hole 1. 2. preparing the wiring Locate the site for the hole directly below the joist or support brace that will hold the outlet box and fan. Cut a 4" diameter hole through the drywall or plaster of the ceiling as shown in Figure 5. You will use the hole to install the support brace and outlet box. 1. Ceiling Joist Support Brace 2. 3. 4" Diameter Ceiling Hole Ceiling 4.
4. Align the slotted holes (refer to Figure 9) in the ceiling plate with the pilot holes in the wood support structure. Note: The isolation pads should be flush against the ceiling. For Angled Ceilings: Be sure to orient the ceiling plate so that the arrows on the ceiling plate are pointing towards the ceiling peak. Refer to Figure 9.
3. 4. Place the receiver in the canopy. Connect the wires as shown in Figure 13. To connect the wires, twist tie bare metal leads together. Place a wire nut over the intertwined length of wire and twist clockwise until tight. C AUTI O N: BBee ssur ur o bbaare w ir ir uree n no wir iree oorr w wir iree ssttr ands aarre vviis o nn ib ibll e aaffter m maakin ingg cco nnee c ti ons .
Grommet Fan Blade 3. If you used grommets, the blades may appear slightly loose after screws are tightened. This is normal. Remove the shipping bumpers from the top of the motor assembly as shown in Figure 21. Shipping Bumper Screws Shipping Bumpers Figure 18 - Inserting the grommets into the fan blades 2. Attach each blade to blade iron using three blade assembly screws as shown in Figure 19. Some fans feature a decorative medallion as well as a blade iron.
attaching the decorative clamps attaching the light fixture Your Hunter Fan comes with two decorative clamps: upper clamp 1. and lower clamp. Each clamp assembly is made up of two pieces. 1. Install three #6-32 housing assembly screws into the motor housing as shown in Figure 26. Do not completely tighten the three screws. Place the two halves of the lower clamp around the lower end of the spindle and the motor adapter.
6. 7. 8. Place the glass bowl over the threaded rod. Place the cap and finial over the threaded rod. Screw the finial onto the threaded rod until tight. Slide the support arms together until they are tight to the glass. Tighten the three screws on the support arms. operating your ceiling fan 1. 2.
• 3. 4. Release the light button when the desired light level is reached. • Continue to hold the light button to repeat the cycle. (Maximum–light level decrease–OFF) • While the light is ON, holding the light button will decrease the light brightness. • Turning the light OFF resets the dimming function. The next press of the light button will start at maximum brightness. Fan Operation: • Press the High, Medium, or Low speed buttons to turn the ceiling fan ON at the desired speed.
troubleshooting Problem: Nothing happens; fan does not move. 1. Turn power on, replace fuse, or reset breaker. 2. Loosen canopy, check all connections according to the w ir in he ffaan section. irin ingg tth 3. Check the plug connection in the switch housing. 4. Push motor reversing switch firmly up or down to ensure that the switch is engaged. 5. Remove the shipping bumpers. Problem: Noisy operation. 1. Tighten the blade bracket screws until snug. 2. Tighten the blade screws until snug. 3.
