Vivien Installation Manual Model: 59650 Brushed Nickel 59651 Painted Brass Fan weight ±2 lbs: 23.1 lbs (10.5 kg) ©2019 Hunter Fan Co.
Congratulations on purchasing your new Hunter® ceiling fan! The ceiling fan you purchased will provide comfort and performance in your home or office for many years. This instruction manual contains complete instructions for installing and operating your fan. We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world. We are here to help! This Instruction Manual is designed to make installation as simple as possible.
1886 Here is what comes in your box: We recommend that you pull everything out of the box and lay it out. We have grouped the drawn components below with the hardware you’ll need for those parts. The screws below are drawn to scale to make it easier to identify what piece of hardware is needed to install each component. Hunter Pro Tip: Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag.
1886 Choosing the Right Installation Location You probably bought this fan with a location in mind. Let’s check below to make sure it is a good fit. Check the room dimensions: Check the outlet box: 30 inches from blade tip to nearest wall or obstruction You must be able to secure the fan to building structure or fan-rated outlet box.
1886 Installing the Ceiling Bracket You have two options for installation. Pick which one works best for your location. Remove any existing bracket prior to installation. Only use the provided Hunter ceiling bracket that came in your fan’s box. Hunter Pro Tip: The machine screws are the ones that came with your outlet box.
1886 STEP STEP Installing the Downrod 4 5 Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. Lower the adapter cover until it rests flush against the motor housing. WARNING FAN FALL HAZARD To prevent SERIOUS INJURY or DEATH: • ALWAYS tighten setscrew with pliers. • DO NOT hand tighten setscrew. • CHECK the setscrew is tight using pliers each time you change fan direction.
1886 Wiring the Fan We know wiring is hard. Let’s make it easier. Follow these steps to get your fan wired quickly and safely. Follow the route below that best matches your wall switch setup. If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician. You are going to need these: Hunter Pro Tip: 4 Wire Nuts (these are in the Here is how to connect the wires: Push the bare metal ends of the wires together and slide a wire nut over them.
1886 Installing the Canopy Insert the two canopy screws found in the hardware bag. x2 bag Canopy Screw op Fi t t h e c a n yi n pla ce as s h o w n. Lift the canopy into place so that the screw holes are aligned. Installing the Blades: Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade arm with screws found in the hardware bag. x12 Blade Screw bag x12 Grommet bag IMPORTANT Repeat x4 Note: Fan style may vary.
1886 Assembling the Light Remove the cardboard plug guard before proceeding! Notch Notch Notch Push the connector and excess wire into the hole at the top of the light fixture. Connect the plugs from the fan and light fixture. Make sure to line up the colored markings on the connectors. IMPORTANT The connector and excess wiring must be pushed into the light fixture in order to successfully mount the light fixture to the fan. Note: Pin Raise the light kit to the bottom of the fan.
1886 Preparing the Remote The remote control is already paired for use. For your convenience, a remote function card is packed in with your remote. NOTICE • Always purchase the correct size and grade of battery most suitable for the intended use. • Replace all batteries of a set at the same time. • Clean the battery contacts and also those of the device prior to battery installation.
1886 Troubleshooting Fan Doesn’t Work Remote Only Works Close to Fan • Make sure power switch is on. • • Check the circuit breaker to ensure the power is turned on. Change battery. Noisy Operation • Make sure the blades spin freely. • Make sure the blades are properly installed. • Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram. • Check to see if any of the blades are cracked. If so, replace all of the blades.
1886 Downrod If you need a different downrod length follow these steps: Follow steps 1-5 to remove standard downrod pipe 1 10 2 3 9 4 8 Follow steps 6-10 to reassemble with new downrod 5 7 6 WARNING FAN FALL HAZARD To prevent SERIOUS INJURY or DEATH: • ALWAYS follow the downrod assembly instructions exactly. • VERIFY the downrod is assembled correctly by firmly pulling on the hanger ball.
