ITM. / ART. 1600104 Contempo II LED Installation Manual Model: 59476 Brushed Nickel Weight ±2 lbs: 21.6 lbs(9.8 kg) ©2017 Hunter Fan Co.
1886 Congratulations on purchasing your new Hunter® ceiling fan! The ceiling fan you purchased will provide comfort and performance in your home or office for many years. This instruction manual contains complete instructions for installing and operating your fan. We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world. Need a little more help with installation? Visit our We are here to help! installation video at: http://bit.
1886 Here is what comes in your box: We recommend that you pull everything out of the box and lay it out. We have grouped the drawn components below with the hardware you’ll need for those parts. The screws below are drawn to scale to make it easier to identify what piece of hardware is needed to install each component. Wood Screw Hunter Pro Tip: Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag.
1886 Choosing the Right Installation Location You probably bought this fan with a location in mind. Let’s check below to make sure it is a good fit. Check the room dimensions: Check the outlet box: 30 inches from blade tip to nearest wall or obstruction You must be able to secure the fan to building structure or fan-rated outlet box.
1886 Installing the Ceiling Bracket You have two options for installation. Pick which one works best for your location. Remove any existing bracket prior to installation. Only use the provided Hunter ceiling bracket that came in your fan’s box. Hunter Pro Tip: The machine screws are the ones that came with your outlet box.
1886 Hanging the Fan S li d e c a n o p y ove NOTICE rd o wn ro d an d To prevent damage to fan, ALWAYS lift holding either the fan housing or the downrod. w i re s . Place the downrod ball into the slot in the ceiling bracket. Progress Check: Your fan should look like this. Need a little more help with installation? Visit our 6 installation video at: http://bit.
1886 Wiring the Fan We know wiring is hard. Let’s make it easier. Follow these steps to get your fan wired quickly and safely. Follow the route below that best matches your wall switch setup. If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician. Hunter Pro Tip: NOTICE Here is how to connect the wires: Push the bare metal ends of the wires together and slide a wire nut over them. Then, twist the wire nut clockwise until tight.
1886 Installing the Canopy Insert the two canopy screws found in the hardware bag. x2 bag Canopy Screw op Fi t t h e c a n yi n pla ce as s h o w n. Lift the canopy into place so that the screw holes are aligned. Installing the Blades: Align the three holes in the blade with the three blade iron posts. Squeeze the blade and the blade post together. The flared tops of the blade iron posts will be fully visible above the blade when properly assembled.
1886 Assembling the Trim Ring Screw Screw Screw After rotating the trim ring into place, tighten all three screws securely. Rotate the light fixture counterclockwise. Ensure all three screws are engaged in the keyhole slots. Lift the trim ring so that the larger keyhole slots slide over the screws. Make sure the plug connector is pushed through the central hole in the trim ring. WARNING FAN FALL HAZARD Make sure all three screws are tight to secure the trim ring to the mounting plate.
1886 Preparing the Remote Control The remote control is already paired for use. NOTICE • Always purchase the correct size and grade of battery most suitable for the intended use. • Replace all batteries of a set at the same time. Battery Door • Clean the battery contacts and also those of the device prior to battery installation. • Ensure the batteries are installed correctly with regard to polarity (+ and -). • Remove batteries from equipment which is not to be used for an extended period of time.
1886 Controlling Your Fan For your convenience, a remote function card is packed in with your remote. Reverse Switch Light On/Off Fan On/Off Fan Speed Up Fan Speed Down Ceiling fans work in two directions: downdraft (counterclockwise rotation) and updraft (clockwise rotation). To change the direction of air flow, turn the fan off and let it come to a complete stop. The reversing switch is located inside the light fixture. It can only be accessed when the glass is removed.
1886 Limited Lifetime Warranty • ENERGY STAR® Rated Light Kits — Three-Year Limited Warranty If your ENERGY STAR rated light kit (not including glass components) fails at any time within three years of the date of purchase due to a defect in material or workmanship, as determined solely by Hunter, Hunter will provide a replacement light kit free of charge.* Hunter Fan Company grants this limited warranty to the original purchaser of this Hunter ceiling fan. This document can be found at www.HunterFan.com.