Searow Installation Manual Model: 55085 Matte Silver 55086 Matte Black Fan weight ±2 lbs: 24.4 lbs (11.1 kg) ©2019 Hunter Fan Co.
Congratulations on purchasing your new Hunter® ceiling fan! The ceiling fan you purchased will provide comfort and performance in your home or office for many years. This instruction manual contains complete instructions for installing and operating your fan. We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world. We are here to help! This Instruction Manual is designed to make installation as simple as possible.
Here is what comes in your box: 1886 Hunter Pro Tip: We recommend that you pull everything out of the box and lay it out. We have grouped the drawn components below with the hardware you’ll need for those parts. The screws below are drawn to scale to make it easier to identify what piece of hardware is needed to install each component. Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag.
1886 Choosing the Right Installation Location You probably bought this fan with a location in mind. Let’s check below to make sure it is a good fit. Check the room dimensions: Check the outlet box: 30 inches from blade tip to nearest wall or obstruction You must be able to secure the fan to building structure or fan-rated outlet box.
1886 Preparing the Ceiling Bracket Do this first! STEP OFF STEP x4 To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location. Canopy Plate Screw bag x4 Flange Nuts 2 STEP rn Tu WARNING r we Po 3 1 Remove all four mounting isolators. Install the ceiling plate gasket onto the ceiling plate.
1886 Installing the Downrod Follow below if you are using the downrod that came pre-assembled in your box. Need to install a longer or shorter downrod? Check out the guide at the end of this manual. 1 STEP STEP STEP Hunter Pro Tip: 2 3 The ground wire attached to the downrod is approximately 8 inches. ! KEEP Slide the adapter cover onto the downrod until it rests against the hanger ball. Remove the pre-installed setscrew so that the downrod can be inserted.
1886 Wiring the Fan We know wiring is hard. Let’s make it easier. Follow these steps to get your fan wired quickly and safely. Follow the route below that best matches your wall switch setup. If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician. You are going to need these: Hunter Pro Tip: 4 Wire Nuts (these are in the Here is how to connect the wires: Push the bare metal ends of the wires together and slide a wire nut over them.
1886 Installing the Canopy Insert the two canopy screws found in the hardware bag. x2 bag Canopy Screw op Fi t t h e c a n yi n pla ce as s h o w n. Lift the canopy into place so that the screw holes are aligned. Installing the Blades: Put the blade washers found in the hardware bag onto the blade screws found in the hardware bag. Then install the blade screws to secure each blade to the fan.
1886 Assembling the Light 2 of 3 1 of 3 Light Kit Screw bag Light Kit Screw bag Partially install two light kit screws, found in the hardware bag, through the upper switch housing gasket halfway into the motor housing as shown. It does not matter which two screw holes you choose. Lift the upper switch housing and align the keyhole slots in the top of the upper switch housing with the partially installed light kit screws.
1886 Preparing the Wall Control 1 Turning off the power KEY PRESS Ensure the power is OFF at the outlet box and wall switch location before proceeding with installation. LIGHT FUNCTIONS n Tur 2 Installing the battery To access the battery compartment, slide the battery door up. FUNCTION er Pow Light On/Off OFF Light Dimming Control Long Press Long Press Battery Door Long Press Replace the used battery with two AAA batteries when needed.
1886 Troubleshooting Fan Doesn’t Work Noisy Operation • Make sure power switch is on. • Make sure the blades are properly installed. • Check the circuit breaker to ensure the power is turned on. • Check to see if any of the blades are cracked. If so, replace all of the blades. • Make sure the blades spin freely. • Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram.
1886 Downrod If you need a different downrod length follow these steps: Follow steps 1-5 to remove standard downrod pipe 1 10 2 3 9 4 8 5 7 6 Follow steps 6-10 to reassemble with new downrod WARNING FAN FALL HAZARD To prevent SERIOUS INJURY or DEATH: • ALWAYS tighten setscrew with pliers. • DO NOT hand tighten setscrew. • CHECK the setscrew is tight using pliers each time you change fan direction.
