www.HunterFan.com Table of Contents Ceiling Plate Tools Needed Top Housing 30 inches Ladder Hanging the Fan To register your fan, please visit: www.HunterFan.com/register 9 Operation, Maintenance & Cleaning 12 Troubleshooting ? ? ? 18 PA G E 1 M3608-01 • 05/09/16 • © 2016 Hunter Fan Company 16 PA G E PA G E PA G E 15 Blades PA G E Remote Control 13 5 PA G E 9 PA G E Hood 4 Canopy Wiring PA G E 7 Save your receipt for proof of purchase.
www.HunterFan.com What to Expect with Your Installation 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box 7 feet from bottom edge of blade to the floor Know your wiring Assess location You may need a friend to help you.
www.HunterFan.com Tools Needed Ladder Screwdrivers Pliers 1.888.830.1326 Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M3608-01 • 05/09/16 • © 2016 Hunter Fan Company Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag. The symbols can be used to identify the appropriate hardware for each step.
www.HunterFan.com Ceiling Plate 1.888.830.1326 Bumper r we o nP r Tu OFF Make sure all four bumpers are still attached. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling plate and is acceptable for fan with hardware found in support of 31.
Top Housing www.HunterFan.com Top Housing 1.888.830.1326 Trim Ring Canopy Adapter Adapter Thread the wires through the top housing. Place the top housing onto the motor housing so that the holes in the top housing lineup with the holes in the motor housing and the adapter. Rest the trim ring on the top housing. 5 M3608-01 • 05/09/16 • © 2016 Hunter Fan Company Place the canopy on the top housing. Ensure all four screw holes line up with the screw holes in both the top housing and the adapter.
www.HunterFan.com STRIP CUT Top Housing (continued) Top Housing Screws (not to scale) 8” & 3/8” Grounding Screw Install the top housing screws. Install the grounding screw in the smaller screw hole. These screws can be found in the hardware bag. The wires can be cut, but leave at least 8” extending from the top of the canopy. 8” 3/8” 6 M3608-01 • 05/09/16 • © 2016 Hunter Fan Company 1.888.830.
www.HunterFan.com Hanging the Fan Ceiling Plate Hook Ceiling Plate Hook Raise the fan and align the slots in the canopy with the hooks on the ceiling plate. Note: To hang the fan, you must tilt the canopy to an almost vertical position so that the canopy slots sit on the ceiling plate hooks. Place the slots over the ceiling plate hooks to hang the fan. Note: Fan style may vary. 7 M3608-01 • 05/09/16 • © 2016 Hunter Fan Company 1.888.830.
Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. www.HunterFan.com OM FR Receiver G green/yellow stripe (grounding) Using an orange wire connector from the hardware bag, connect the 3 grounding wires (green, green/ yellow stripe, or bare copper) coming from the ceiling and ceiling plate. CEILIN 1.888.830.
Wiring (continued) OM FR www.HunterFan.com white (grounded) OM FAN FR white OM white black FR M FA N 1.888.830.1326 OM CEILING FR black (ungrounded) Using the orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black wire from the receiver. Connect the white wire (grounded) from the ceiling to both the white wire from the receiver and the white wire from the fan.
www.HunterFan.com Canopy 1.888.830.1326 Ceiling Plate Hooks Canopy Screw Canopy Screw Screw Holes Swing the fan up to align the canopy screw holes with the mounting holes on the ceiling plate. Note: The slots in the canopy must remain engaged while swinging the canopy for alignment. Hold the canopy up with the screw holes aligned. Partially install two canopy screws, found in the hardware bag, into the holes opposite the ceiling plate hooks.
www.HunterFan.com Canopy (continued) Canopy Trim Ring Using both hands, push the canopy trim ring up to the top of the canopy. The canopy trim ring will snap and lock into place. Note: Should you need to remove the trim ring, press firmly on opposite sides of the trim ring. The tabs will flex out releasing the canopy trim ring. 11 M3608-01 • 05/09/16 • © 2016 Hunter Fan Company 1.888.830.
Blades www.HunterFan.com Attach each blade to a blade iron using three blade washers, found in the hardware bag, and three blade assembly screws, found in the hardware bag. 12 M3608-01 • 05/09/16 • © 2016 Hunter Fan Company 1.888.830.
Hood www.HunterFan.com Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. Feed the wire plug through the center hole of the hood, then wrap keyhole slots around the screws and twist counterclockwise. 1.888.830.1326 Insert the third screw, found in the hardware bag, into place and then tighten all three screws. Make sure the hood is securely attached to the mounting plate.
www.HunterFan.com Hood (continued) CONGRA T 1.888.830.1326 YOU’REULATIONS! DONE! Connect the plugs from the fan and lower switch housing. Make sure to line up the colored markings on the connectors. Insert the longer screws, found in the hardware bag, into place and then tighten all three screws. Install the bulb into the socket. When necessary, replace with bulb of the same type and wattage.
www.HunterFan.com Remote Control Battery Door 1.888.830.1326 r we o nP r Tu ON Phillips Head Screw To access the battery compartment, remove the small Phillips head screw that secures the battery door to the transmitter assembly. The battery should be installed with the positive (+) side up. Replace with a CR2032 battery when necessary. The remote transmitter should already be paired to the receiver and ready to use.
Operation, Maintenance, & Cleaning www.HunterFan.com 1.888.830.1326 Safe-Exit Medium Speed Fan Off The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off to exit the room before the lights go out. To use Safe-Exit: High Speed Switch Cover Plate Low Speed Light • The lights will flash for visual confirmation. Removed Tabs To turn on fan, press a fan speed button. Speeds range from off (0) to high (3). Quickly press the Light button to turn the lights off and on.
Operation, Maintenance, & Cleaning (continued) www.HunterFan.com Reverse Switch To switch the direction of air flow, move the reverse switch to the opposite position. For cleaning the fan, use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes. 17 M3608-01 • 05/09/16 • © 2016 Hunter Fan Company 1.888.830.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely.
