www.HunterFan.com Table of Contents Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. Ceiling Plate Top Housing 30 inches 3 Wiring Hanging the Fan 4 Canopy 5 11 PA G E Ladder PA G E 2 PA G E 7 feet PA G E To register your fan, please visit: www.HunterFan.
www.HunterFan.com What to Expect with Your Installation 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. WARNINGS If you are unfamiliar with wiring, use a qualified electrician. 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box 7 feet from bottom edge of blade to the floor Know your wiring Assess location You may need a friend to help you.
www.HunterFan.com Tools Needed Ladder Screwdrivers Pliers 1.888.830.1326 Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M623-01 • 11/18/16 • © 2016 Hunter Fan Company Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag. The symbols can be used to identify the appropriate hardware for each step.
www.HunterFan.com Ceiling Plate 1.888.830.1326 Bumper r we o nP r Tu OFF Make sure all four bumpers are still attached. Use wood screws (included) when securing to support structure with approved electrical outlet box. Drill 9/64” pilot holes in support structure to aid in securing ceiling plate with hardware found in the hardware bag.
Top Housing www.HunterFan.com Top Housing Trim Ring Canopy Adapter Adapter Thread the wires through the top housing. 1.888.830.1326 Place the top housing onto the motor housing so that the holes in the top housing lineup with the holes in the motor housing and the adapter. Rest the trim ring on the top housing. 5 M623-01 • 11/18/16 • © 2016 Hunter Fan Company Place the canopy on the top housing. Ensure all four screw holes line up with the screw holes in both the top housing and the adapter.
www.HunterFan.com STRIP CUT Top Housing (continued) Top Housing Screws (not to scale) 8” & 3/8” Grounding Screw Install the top housing screws. Install the grounding screw in the smaller screw hole. These screws can be found in the hardware bag. The wires can be cut, but leave at least 8” extending from the top of the canopy. 8” 3/8” 6 M623-01 • 11/18/16 • © 2016 Hunter Fan Company 1.888.830.
www.HunterFan.com Hanging the Fan Ceiling Plate Hook Ceiling Plate Hook Raise the fan and align the slots in the canopy with the hooks on the ceiling plate. Note: To hang the fan, you must tilt the canopy to an almost vertical position so that the canopy slots sit on the ceiling plate hooks. Place the slots over the ceiling plate hooks to hang the fan. Note: Fan style may vary. 7 M623-01 • 11/18/16 • © 2016 Hunter Fan Company 1.888.830.
Wiring: Single Switch www.HunterFan.com Dual Switch Instructions Have a single switch? Follow these steps: Ground ed White Connect the grounding wires (green, green/ yellow stripe, or bare copper) coming from the ceiling and ceiling plate. 1.888.830.1326 Un gro Black g Groundin un Connect the white (grounded) wire from the ceiling to the white wire from the fan. de d Blue Green/Yellow Stripe Connect the black wire (ungrounded) from the ceiling to the black and the blue wires from the fan.
Wiring: Dual Switch www.HunterFan.com Have dual switches? Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. Follow these steps: Ground ed White Un gro un d g g Un Groundin Connect the white (grounded) wire from the ceiling to the white wire from the fan. de Black Connect the black wire (ungrounded) from the ceiling to the black wire from the fan.
www.HunterFan.com Canopy 1.888.830.1326 Ceiling Plate Hooks Canopy Screw Screw Holes Canopy Screw Swing the fan up to align the canopy screw holes with the mounting holes on the ceiling plate. Note: The slots in the canopy must remain engaged while swinging the canopy for alignment. Hold the canopy up with the screw holes aligned. Partially install two canopy screws, found in the hardware bag, into the holes opposite the ceiling plate hooks.
Blades www.HunterFan.com Secure each blade to a blade iron as shown using the blade nuts, found in the hardware bag, and the blade assembly screws, found in the hardware bag. Lightly attach the blade irons to the motor with screws found in the hardware bag, then securely tighten after both screws are attached. 11 M623-01 • 11/18/16 • © 2016 Hunter Fan Company 1.888.830.
Switch Housing Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. www.HunterFan.com Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. Note: Remove the three pre-installed screws from the switch housing and save the screws. You will need them later. 1.888.830.
www.HunterFan.com Switch Housing (continued) Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Align the the screw holes in the upper switch housing posts with the holes in the lower switch housing. Raise the switch housing to the upper switchhousing 13 M623-01 • 11/18/16 • © 2016 Hunter Fan Company 1.888.830.1326 Install the three switch housing screws. Tighten all three screws securely.
www.HunterFan.com Light Kit Light Pull Chain 1.888.830.1326 Fan Pull Chain CONGRA T YOU’REULATIONS! DONE! Lift the shade and attach it to the upper switch housing using the three thumbscrews. Tighten all three screws securely by hand. Connect the appropriate pull chain pendant to each of the short chains coming from the light kit. The fan pull chain controls the speed: from high to off. The light pull chain controls the light fixture: on and off.
Maintenance & Cleaning www.HunterFan.com 1.888.830.1326 r we o nP r Tu ON Reverse Switch Changing the bulb - Unscrew the bulb and replace with a bulb of same type and wattage. Changing the direction of air flow - move the reverse switch to the opposite position. 15 M623-01 • 11/18/16 • © 2016 Hunter Fan Company Cleaning the fan - use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely.
