www.HunterFan.com Table of Contents Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. What to Expect with Your Installation Tools Needed Mounting Options 1.888.830.
www.HunterFan.com What to Expect with Your Installation 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. WARNINGS If you are unfamiliar with wiring, use a qualified electrician. 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring You may need a friend to help you. Ceiling angles greater than 34° will require an Angled Mounting Kit. See page 4 for details.
www.HunterFan.com Tools Needed Ladder Screwdrivers Pliers 1.888.830.1326 Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M3622-01 • 10/19/16 • © 2016 Hunter Fan Company Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag. The symbols can be used to identify the appropriate hardware for each step.
34O CEILING www.HunterFan.com Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
www.HunterFan.com Ceiling Bracket 1.888.830.1326 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
Blade Irons & Top Housing www.HunterFan.com Place the motor in one of the holes in the packaging. Install a blade iron to the blade iron mounting plate using two blade iron assembly screws, found in the hardware bag. Repeat this process to install all blade irons. 6 M3622-01 • 10/19/16 • © 2016 Hunter Fan Company 1.888.830.
Blade Irons & Top Housing (continued) Thread the wires through the top housing. www.HunterFan.com Install the top housing screws. These screws can be found in the hardware bag. 7 M3622-01 • 10/19/16 • © 2016 Hunter Fan Company 1.888.830.1326 You will need to flip the fan over before proceeding to the next step.
Light Kit www.HunterFan.com Partially install two light kit assembly screws, found in the hardware bag, halfway into the motor housing as shown. It does not matter which two screw holes you choose. Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. 8 M3622-01 • 10/19/16 • © 2016 Hunter Fan Company the 1.888.830.1326 Insert the third screw, found in hardware bag, into place and then tighten all three screws.
www.HunterFan.com Light Kit (continued) Connect the plug connectors found in the switch housing area of the light kit assembly. Make sure to line up the colored markings on the connectors. Lower the light kit. Align the screw holes in the light kit with the screw holes in the upper switch housing. 9 M3622-01 • 10/19/16 • © 2016 Hunter Fan Company 1.888.830.1326 Install the three switch housing screws, found in the hardware bag, through the light kit and into the switch housing.
www.HunterFan.com Light Kit (continued) Connect the white wire from the fan to the white wire from the light kit. Then, connect the blue wire from the fan to the black wire from the light kit. Lower the LED assembly to the posts in the housing. Make sure the light kit assembly is securely attached to the motor housing. Failure to properly secure all three assembly screws could result in the light fixture falling. Attach the LED assembly using the LED assembly screws found in the hardware bag.
www.HunterFan.com Option 1 Downrod 1.888.830.
www.HunterFan.com KEEP! (not to scale) 8” & 3/8” 1.888.830.1326 STRIP CUT Downrod (continued) ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
www.HunterFan.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 13 M3622-01 • 10/19/16 • © 2016 Hunter Fan Company 1.888.830.
Wiring: Single Switch www.HunterFan.com Dual Switch Instructions Have a single switch? Follow these steps: Grou White Gr ou ed und Ungro nd ing i pe Str Black Green/Yellow Stripe Blue Connect the black wire (ungrounded) from the ceiling to the black wire from the fan. nded ellow Green/Y Connect the white (grounded) wire from the ceiling to the white wire from the fan. 1.888.830.
Wiring: Dual Switch www.HunterFan.com 1.888.830.1326 Have dual switches? Follow these steps: Grounded ellow Green/Y Grounded White Gr ou Ungrounded (lig ht) Black ing rou nd ed Green/Yellow Stripe Connect the three grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and hanging bracket. Un g Connect the black wire (ungrounded) from the ceiling to the black wire from the fan.
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. 16 M3622-01 • 10/19/16 • © 2016 Hunter Fan Company 1.888.830.
Blades www.HunterFan.com Secure each blade to a blade iron as shown using the blade nuts, found in the hardware bag, and the blade assembly screws, found in the hardware bag. 17 M3622-01 • 10/19/16 • © 2016 Hunter Fan Company 1.888.830.
www.HunterFan.com Glass Tab 1.888.830.1326 Notch CONGRA T YOU’REULATIONS! DONE! Position the notches in the outer rim of the globe so they line up with the tabs on the light kit assembly. Carefully lift the globe up inside the light fixture as far as it will go. Rotate the globe in a clockwise direction until it is held tightly in place by the three tabs. 18 M3622-01 • 10/19/16 • © 2016 Hunter Fan Company See next page for fan operation instructions.
www.HunterFan.com Remote Control Battery Door 1.888.830.1326 r we o nP r Tu ON Phillips Head Screw The remote transmitter is already paired to the receiver and ready to use. To access the battery compartment, remove the small Phillips head screw that secures the battery door to the transmitter assembly. The battery should be installed with the positive (+) side up. Replace with a CR2032 battery when necessary. Note: If your need to pair your remote, remove the battery door.
www.HunterFan.com Remote Control Cradle 1.888.830.1326 You have two options to install the included remote control cradle to the wall. Choose which path works best for you. Option 1: Using Screws Option 2: Using Adhesive Strip Choose your cradle installation location. Remove the cradle from the cradle bracket. If you are installing into drywall, drill two 9/64 width holes using the cradle bracket as a guide. Gently hammer the included drywall anchors into the pre-drilled holes.
Operation, Maintenance, and Cleaning www.HunterFan.com 1.888.830.1326 Light Button Fan Button Fan Control Fan Operation: Press and quickly release the fan button on the remote control to turn the fan OFF or ON. Use the fan control directional pad to raise or lower the fan to the desired speed. Press and hold the fan button to reverse the fan direction. Light Operation: Press and quickly release the light button on the remote control to turn the light OFF or ON.
www.HunterFan.com Troubleshooting 1.888.830.1326 Fan doesn’t work Excessive wobbling Noisy Operation Wireless Issues • Make sure power switch is on. • Make sure the blades are properly installed on the blade iron posts. • Make sure the blades are properly installed on the blade iron posts. • Turning the fan on and off at the switch can resolve some wireless issues. • Turn the power off, support the fan carefully, and check that the hanger ball is properly seated.
