www.HunterFan.com Table of Contents What to Expect with Your Installation Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. Tools Needed Mounting Options 1.888.830.
www.HunterFan.com What to Expect with Your Installation 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring You may need a friend to help you. Ceiling angles greater than 34° will require an Angled Mounting Kit. See page 4 for details.
www.HunterFan.com Tools Needed Ladder Screwdrivers Pliers 1.888.830.1326 Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M3641-01 • 12/20/16 • © 2016 Hunter Fan Company Do not discard the hardware bags or mix parts from different bags. Make note of the symbol printed on each hardware bag. The symbols can be used to identify the appropriate hardware for each step.
34O CEILING www.HunterFan.com Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
www.HunterFan.com Ceiling Bracket 1.888.830.1326 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
www.HunterFan.com Option 1 Downrod 1.888.830.
www.HunterFan.com KEEP! (not to scale) 8” & 3/8” 1.888.830.1326 STRIP CUT Downrod (continued) ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
www.HunterFan.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 8 M3641-01 • 12/20/16 • © 2016 Hunter Fan Company 1.888.830.
Wiring www.HunterFan.com Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. 1.888.830.1326 OM CEILING FR Receiver green/yellow stripe (grounding) Using an orange wire connector from the hardware bag: Connect the 3 grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and ceiling bracket.
Wiring (continued) OM FR • Connect the blue wire from the receiver to the blue wire (or possibly black with white stripe wire) from the fan. • Connect the white (grounded) wire from the ceiling to both the white wire from the receiver and the white wire from the fan. FRO white FR M FA N OM FAN FR OM white Connect the black (ungrounded) wire from the ceiling to the black wire from the receiver. black • blue Connect the yellow wire from the receiver to the black wire from the fan.
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. 11 M3641-01 • 12/20/16 • © 2016 Hunter Fan Company 1.888.830.
Blades www.HunterFan.com Attach each blade to a blade iron using the blade washers, found in the hardware bag, and the blade assembly screws, found in the hardware bag. 12 M3641-01 • 12/20/16 • © 2016 Hunter Fan Company 1.888.830.
Switch Housing Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. www.HunterFan.com Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. 1.888.830.1326 Insert the third screw, found in the hardware bag, into place and then tighten all three screws. Make sure the upper switch housing is securely attached to the mounting plate.
www.HunterFan.com Light Kit Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Lift the lower switch housing until its screw holes are aligned with the screw holes in the upper switch housing. 1.888.830.1326 Install the three switch housing screws, found in the hardware bag. Tighten all three screws.
www.HunterFan.com Light Kit (continued) 1.888.830.1326 Tab Notch CONGRA T YOU’REULATIONS! DONE! Install a bulb into the socket. When necessary, replace with bulb of the same type and wattage. Lift the globe and align the notches in the globe with the tabs in the light kit. Attach the glass bowl to the light kit by twisting it clockwise until it snaps into place. 15 M3641-01 • 12/20/16 • © 2016 Hunter Fan Company See next page for fan operation instructions.
Wall Control 1 www.HunterFan.com 3 Turning off the power Ensure the power is OFF at the outlet box and wall switch location before proceeding with installation. n Tur Wiring the Wall Control Connect the grounding wire from the wall control to the ground control from the switch box using the provided wire nuts. Connect the “LIVE IN” from the switch box to the “~VAC” from the wall control using the provided wire nuts.
Wall Control (continued) 5 Installing the Wall Plate 6 Turning on the power www.HunterFan.com Install the shorter screws through the wall control plate and into the screw holes in the wall control. IMPORTANT Use the pull-chain switch on the fan to set the fan speed to the HIGH position before operation. n Tur 7 The remote transmitter is already paired to the receiver and ready to use.
Wall Control (continued) KEY PRESS www.HunterFan.com KEY PRESS FUNCTION FUNCTION LIGHT FUNCTIONS Long Press Long Press Long Press FAN FUNCTIONS Light On/Off Fan On/Off Light Dimming Control Fan Speed Control Long Press Long Press Light High Light Low + Dimming Mode On/Off Fan High Fan Low Power On/Off Long Press 18 M3641-01 • 12/20/16 • © 2016 Hunter Fan Company + Pair Function 1.888.830.
Operation, Maintenance, & Cleaning www.HunterFan.com r we o nP r Tu ON Reverse Switch Changing the direction of air flow - move the reverse switch to the opposite position. You will need to remove the glass to do so. 19 M3641-01 • 12/20/16 • © 2016 Hunter Fan Company Cleaning the fan - use soft brushes or cloths to prevent scratching. Cleaning products may damage the finishes. 1.888.830.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely.
