Ceiling Fan & Video Universal Remote Control Owner’s Manual Hunter Fan Company ® 41536-01 1/25/2002 1
READ AND SAVE THESE INSTRUCTIONS Caution: Risk of Electrical Shock! Transmitter Model No. 27177 This device complies with part 15 of the FCC rules. Changes or modifications not expressly approved by Hunter Fan Company could void your authority to operate this equipment! Operation Is Subject To The Following Two Conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
table of contents setting up your remote control .................................. 4 installing your batteries ......................................................... 4 setting your remote dip switches .......................................... 4 programming your device code ............................................ 5 testing your device code ........................................................ 5 checking your device code ....................................................
setting up your remote control installing your batteries 1. Remove the battery cover. 2. Install 4 AA batteries. setting your remote dip switches Your dip switches control the radio frequency signal that is used to control your Hunter ceiling fan. The dip switches in the remote should be the same as the dip switches/pin jumpers in the receiver that is installed in your Hunter ceiling fan. 1. Set the dip switches in the remote to the same code as the dip switches in the receiver. 2.
setting up your remote control programming your device code VCR TV DVD CBL/SAT 1. Manually turn on your device. 2. On your Hunter Universal Video & Fan Remote, press and hold the device button for 3 seconds. The red indicator light comes on and goes off. 1 2 3 4 5 6 7 8 9 3. Release the device button. The red indicator light comes on as you release the device button. 4. Press the 4 digit code listed for your device brand on pages 7-13.
setting up your remote control checking your device code TV VCR DVD CBL/SAT 1. Press and hold the device button for 3 seconds. The red indicator light comes on and goes off. 2. Release the device button. The red indicator light comes on as you release the device button. 3. Press and release the SELECT button. The red indicator light should go off. 4. The red indicator light should indicate the code by flashes and pauses. A quick flash indicates a zero in the code.
setting up your remote control TV brand codes Akai ........................................................................................................................... 1160, 1035, 1023 Alba ............................................................................................................................................... 1047 A-Mark .......................................................................................................................................... 1051 Amstrad .......
setting up your remote control TV brand codes JBL ................................................................................................................................................ 1034 JCPenny .................................. 1144, 1137, 1122, 1088, 1081, 1080, 1079, 1041, 1032, 1017, 1011 Jensen ................................................................................................................................ 1160, 1033 JVC .....................................................
setting up your remote control TV brand codes Saisho ................................................................................................................................. 1024, 1023 Sampo ....................................................................................................................... 1150, 1127, 1080 Samsung ....................... 1159, 1138, 1123, 1122, 1102, 1082, 1081, 1080, 1079, 1078, 1046, 1023, 1017 Samwon ...........................................................
setting up your remote control VCR brand codes Aiwa .............................................................................................................................................. 2083 Akai ............................................................. 2092, 2058, 2057, 2056, 2055, 2054, 2053, 2052, 2051 Alba ............................................................................................................................................... 2032 Amstrad ..............................
setting up your remote control VCR brand codes M. Wards .................................................................................... 2036, 2009, 2008, 2003, 2002, 2001 NAD .............................................................................................................................................. 2024 NEC .............................. 2118, 2081, 2065, 2064, 2063, 2062, 2061, 2060, 2059, 2016, 2006, 2005 Orion ........................................................................
setting up your remote control DVD brand codes Aiwa .............................................................................................................................................. 3013 Hitachi ........................................................................................................................................... 3020 JVC ..................................................................................................................................... 3021, 3002 Konka ....
setting up your remote control satellite brand codes Alphastar ....................................................................................................................................... 5021 Chaparral ............................................................................................................................ 5020, 5019 Cheyenne ..................................................................................................................................... 5019 Dishnet ......
operating your remote control Some features may not be applicable to your devices. Refer to each device’s owner’s manual for more information about what your devices are capable of doing. power and device button functions The power and device buttons are used to turn off and on your devices and to switch between devices. ERSAL VIDEO & FAN REMOTE UNIV POWER VCR TV INPUT POWER 14 DVD PIP CBL/SAT SWAP POWER - Press the POWER button to turn off or on the selected device.
operating your remote control menu button functions The menu buttons are used to control the menu for all devices. MENU FLIP MENU CLEAR CLEAR MUTE MENU - Press the MENU button to view the selected device’s menu. CLEAR - Press the CLEAR button to exit the selected device’s menu. DIRECTION KEYS - Press the DIRECTION KEYS to move the cursor in the menu screens and program guide of the selected device. SELECT - Press the SELECT button to select items from the selected device’s screen menu.
operating your remote control channel and volume button functions The channel and volume buttons are used to control the channel for the TV and VCR and control the volume. MUTE FLIP INFO FLIP MUTE FLIP - Press the FLIP button to display the previous television channel. MUTE - Press the MUTE button to turn off or on the sound. CHANNEL - Press the CHANNEL button to select the next higher or lower channel. INFO INFO - Press the INFO button to display information on the selected device.
operating your remote control VCR and DVD button functions The VCR and DVD buttons are used to control the play features of both devices. INFO 1 2 3 4 5 6 REC PAUSE - Press the PAUSE button to pause on your screen while using your selected device. PLAY - Press the PLAY button to play while using your selected device. STOP - Press the STOP button to stop your selected device. FFD/REW - Press the FFD/REW button to fast forward or rewind on your selected device.
operating your remote control number keypad button functions The number keypad buttons are used to enter numbers for channels or menu options. 1 2 3 4 5 6 7 8 9 0 ENTER 1 2 3 4 5 6 7 8 9 NUMBER KEYPAD - Press the NUMBER KEYPAD to manually enter the channel numbers. 0 ENTER 18 ENTER - Press the ENTER button after entering channel numbers if necessary. Note: May also be used to select items in the menu view.
operating your remote control fan button functions The fan buttons are used to control your Hunter ceiling fan. ME LO HI OFF REV LO - Press the LO button to set your fan on low speed. LO ME HI OFF ME - Press the ME button to set your fan on medium speed. HI - Press the HI button to set your fan on high speed. OFF - Press the OFF button to turn off your fan. LIGHT - Press the LIGHT button to turn your light off or on. Press and hold the the LIGHT button to dim or brighten the light.
troubleshooting Nothing happens when 1. Make sure batteries are properly installed. operating remote. 2. Replace with 4 new AA batteries. Red indicator light not 1. Make sure batteries are properly installed. blinking when pressing 2. Replace with 4 new AA batteries. buttons. Remote will not operate my 1. Try all codes listed for your device brand. devices. 2. Use the searching for your device code method on page 6. Nothing happens when 1.
FWD/RWD button does not 1. Try all codes listed for your device brand. function. 2. Use the searching for your device code method on page 6. Feel free to contact Hunter Customer Service for assistance at 1-888-830-1326.
warranty HUNTER FAN COMPANY REMOTE CONTROL LIMITED WARRANTY The Hunter Fan Company makes the following limited warranty to the original purchaser of the Hunter Universal Video and Fan Remote (“Control”): Your Control is warranted to be free from defects in material and workmanship for a period of one year from the date of sale. If the Control malfunctions or fails within the warranty period due to a defect in material or workmanship we will replace it free of charge.
41536-01 1/25/2002 23
® Hunter Fan Company 2500 Frisco Avenue Memphis, Tennessee 38125 1-888-830-1326 24 41536-01 1/25/2002
