www.HunterFan.com Table of Contents What to Expect with Your Installation Congratulations on purchasing your new Hunter® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan. Tools Needed Mounting Options 1.888.830.
www.HunterFan.com What to Expect with Your Installation 1.888.830.1326 Read and Save These Instructions This product conforms to UL Standard 507. If you are unfamiliar with wiring, use a qualified electrician. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring You may need a friend to help you. Ceiling angles greater than 34° will require an Angled Mounting Kit. See page 4 for details.
www.HunterFan.com Tools Needed Ladder Pliers Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M3599-01 • 02/09/16 • © 2016 Hunter Fan Company Screwdrivers 1.888.830.
34O CEILING www.HunterFan.com Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
www.HunterFan.com Ceiling Bracket 1.888.830.1326 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
www.HunterFan.com Option 1 Downrod 1.888.830.
www.HunterFan.com Downrod (continued) Hanger Ball KEEP! ! KEEP Adapter Cover Slide the adapter cover onto the downrod until it rests against the hanger ball. Note: The adapter cover is not used for low-profile mounting. Remove the pre-installed setscrew so that the downrod can be inserted. 7 M3599-01 • 02/09/16 • © 2016 Hunter Fan Company Hand tighten the downrod (at least 4-5 full turns) until it stops. 1.888.830.
www.HunterFan.com (not to scale) 8” & 3/8” 1.888.830.1326 STRIP CUT Downrod (continued) The wires can be cut, but leave at least 8” extending from the top of the downrod. Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 8” Lower the adapter cover until it rests flush against the motor housing. 3/8” If the setscrew is not tightened securely, the fan may fall.
www.HunterFan.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 9 M3599-01 • 02/09/16 • © 2016 Hunter Fan Company 1.888.830.
Wiring www.HunterFan.com Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. 1.888.830.1326 OM CEILING FR Receiver green/yellow stripe (grounding) Using an orange wire connector from the hardware bag: Connect the 3 grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and ceiling bracket.
Wiring (continued) OM FR • Connect the blue wire from the receiver to the blue wire (or possibly black with white stripe wire) from the fan. • Connect the white (grounded) wire from the ceiling to both the white wire from the receiver and the white wire from the fan. FRO white FR M FA N OM FAN FR OM white Connect the black (ungrounded) wire from the ceiling to the black wire from the receiver. black • blue Connect the yellow wire from the receiver to the black wire from the fan.
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 12 M3599-01 • 02/09/16 • © 2016 Hunter Fan Company 1.888.830.
Blades www.HunterFan.com Secure each blade to a blade iron as shown using the blade nuts, found in the hardware bag, and the blade assembly screws, found in the hardware bag. 13 M3599-01 • 02/09/16 • © 2016 Hunter Fan Company 1.888.830.
Switch Housing Partially install two light kit assembly screws, found in the hardware bag, halfway into the motor housing as shown. It does not matter which two screw holes you choose. www.HunterFan.com Feed the 9-pin plug connector coming from the bottom of the motor housing through the center hole in the light kit assembly. Connect it to the plug connector found in the switch housing area of the light kit assembly. Make sure to line up the colored markings on the connectors.
www.HunterFan.com Light Kit Insert a third light kit assembly screw, found in the hardware bag, into place and tighten all three screws securely. Make sure the light kit assembly is securely attached to the motor housing. Failure to properly secure all three assembly screws could result in the light fixture falling. Carefully push all switch housing components into the switch housing, then install the switch housing plate using two light kit assembly screws, found in the hardware bag.
www.HunterFan.com Light Kit (continued) 1.888.830.1326 Tab Notch Bulb Install a light bulb in each socket. When necessary, replace with bulbs of the same wattage. Position the notches in the outer rim of the globe so they line up with the tabs on the inside surface of the light fixture rim. Carefully lift the globe up inside the light fixture as far as it will go. Rotate the globe in a clockwise direction until it is held tightly in place by the three tabs.
www.HunterFan.com Remote Control Battery Door 1.888.830.1326 r we o nP r Tu ON Phillips Head Screw To access the battery compartment, remove the small Phillips head screw that secures the battery door to the transmitter assembly. The battery should be installed with the positive (+) side up. Replace with a CR2032 battery when necessary. The remote transmitter should already be paired to the receiver and ready to use.
Operation, Maintenance, & Cleaning www.HunterFan.com 1.888.830.1326 Medium Speed Fan Off High Speed Switch Cover Plate Low Speed Light Removed Tabs To turn on fan, press a fan speed button. Speeds range from off (0) to high (3). Quickly press the Light button to turn the lights off and on. Rocker- Style Plate To install the transmitter cradle, remove the two screws holding the switch cover plate. Do not remove the cover plate.
Operation, Maintenance, & Cleaning (continued) www.HunterFan.com Safe-Exit The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off to exit the room before the lights go out. To use Safe-Exit: • Press the Fan Off button for at least three seconds to initiate the Safe-Exit Mode. • The lights will flash for visual confirmation. • The lights will stay on 50% brightness for 15 seconds and then begin to dim. After a total of 30 seconds, the lights will be completely off.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely.
