Installation Guide

INSTALLATION INSTRUCTIONS
INSTRUCCIONES DE INSTALACIÓN/ INSTRUCTIONS D’INSTALLATION
For Models:
Para los Modelos:
Pour les Modèles:
Here are the
tools you’ll
need to
complete your
installation:
Estas son las
herramientas
que usted
necesitará para
completar su
instalación:
Voici les outils
dont vous
aurez besoin
pour réaliser
l’installation:
Ladder
Escalera
Échelle
Screwdriver
Destornilladore
Tournevis
Pliers
Alicates
Pince
Wire Strippers
Pelacables
Pince à dénuder
READ AND SAVE THESE INSTRUCTIONS
These instructions are provided for your safety. It is very
important that they are read carefully and completely
before beginning installation of the lighting xture.
This product must be installed in accordance with the
applicable installation code by a person familiar with
the construction and operation of the product and the
hazards involved.
LEA Y GUARDE ESTAS INSTRUCCIONES
Estas instrucciones se proporcionan para su seguridad.
Es muy importante leerlas detenidamente y completa-
mente antes de comenzar la instalación de la lámpara.
Este producto debe ser instalado, de acuerdo con
el código de instalación aplicable, por una persona
familiarizada con la construcción y funcionamiento del
producto y con los peligros involucrados.
LISEZ ET CONSERVEZ CES INSTRUCTIONS
Ces instructions sont fournies pour votre sécurité. Il
est très important de les lire attentivement dans leur
intégralité avant d’entreprendre l’installation
du luminaire.
Ce produit doit être installé conformément au code
d’installation en vigueur, par une personne connaissant
bien la conception et le fonctionnement du produit
ainsi que les dangers encourus.
Fixture weight ±2 lbs:
Peso ±2 lb:
Poids xe ±2 lbs:
•
WARNING
• All wiring must be in accordance with national
and local electrical codes ANSI/NFPA 70. If you
are unfamiliar with wiring or in doubt, consult a
qualied electrician.
• To avoid possible electrical shock, before
installing your light xture, disconnect the power
by turning off the circuit breakers to the outlet box
associated with the wall switch location.
• The lighting xture must be grounded. If the
ground wire for the installation site is not present,
immediately STOP installation and consult a
qualied electrician.
•
• Todo el cableado debe realizarse de acuerdo con
los códigos eléctricos locales y nacionales ANSI/
NFPA 70. Si no está familiarizado con el cableado,
o si tiene duda, consulte a un electricista calicado.
• Para evitar una posible descarga eléctrica, antes
de instalar su lámpara, desconecte la energía
apagando los interruptores automáticos (breakers)
que alimentan la caja de salida asociada con la
ubicación del interruptor de pared.
ADVERTENCIA
• L’appareil d’éclairage doit être mis à la terre.
Si le l de terre du lieu d’installation n’est pas
présent, ARRÊTEZ immédiatement l’installation et
consultez un électricien qualié.
•
AVERTISSEMENT
• Tout le câblage doit être conforme aux codes
électriques nationaux et locaux en vigueur et à la
norme ANSI/NFPA70. Si vous n'avez pas l'habitude
de faire ce câblage ou en cas de doute, adressez-
vous à un électricien qualié.
• Pour éviter tout choc électrique, avant d’installer
le luminaire, coupez le courant en éteignant les
disjoncteurs de la boîte électrique associée à
l’interrupteur mural.
• Le luminaire doit être mis à la terre. Si le l
de terre du lieu d’installation n’est pas présent,
ARRÊTER immédiatement l’installation et
consulter un électricien qualié.
©2020 Hunter Fan Co.
Light Cluster
Luz En Racimo
Lumière Grappe
Part #/Pieza #/Pièce #
Hardware Service Kit/Kit De Mantenimiento Del Equipo/Trousse De
Maintenance Quincaillerie
Glass/Domo De Vidrio/Verre
Part #/Pieza #/Pièce #
ENGLISH
Twist or tape wire
ends together to make
it easier to thread
through downrod
Hunter Pro Tip:
NOTICE
In order to use a 12in rod by
itself you must rst remove
the post from the 6in rod and
install it on one of the ends of
the 12in rod.
NOTICE
Drill 9/64" pilot holes in
support structure to aid in
securing light xture.
Drill
Taladro
Foret
Finish/Finish/FiniModel/Modelo/Modèle
Type/Tipo/TypeModel/Modelo/ Modèle
H
L
M
K
G
N
O
P
F
I
J
E
D
C
B
A
Q
19155
19156
Devon Park
KC03205000
KC03204000
Onyx Bengal/Bengala Ónix/
Onyx du Bengale
Brushed Nickel/Níquel Pulido/
Nickel Brossé
19155
19156
KA28401147
KA28401147
Clear/ Transparente/
Transparent
Clear/ Transparente/
Transparent
19156
19155
ML017
r_111320
14.1 lbs (6.40 kg)
3
3
3
FINISHING THE INSTALLATION
CONNECTING THE WIRES
PREPARING FOR INSTALLATION
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light
and wipe down the xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
Carefully remove all contents from the carton. Shut off the power at the circuit breaker and completely remove the old
xture from the ceiling, including the old mounting bracket. Remove the new mounting bracket assembly from the
bag. Mounting plate (B) contains several pairs of threaded holes. Find the pair of holes that matches the spacing on the
holes on the xtures canopy (F). Attach two mounting screws (A) to the mounting plate (B). Tighten nuts (C) to hold the
screws in place. Put the hollow rubber plug (I) inside the hole in the ceiling, then insert the tapping screw (J) through
the mounting plate (B) into the rubber plug (I). Place the mounting plate (B) over the junction box so that mounting
screws (A) and nuts (C) are visible. Pull the house wires through the center of mounting plate (B). Secure mounting
plate (B) to the junction box by tightening the screws (D). Partially install grounding screw (E) into mounting plate (B).
Slide cord (M) through cord grip (K) to adjust the wire to desirable length [set screw (H) may need to be loosened rst].
Tighten the set screw (H) with the included screwdriver (G) to lock it tight. Tie a knot in each cord (M) above the canopy
for strain relief [see existing knot (Q) for example]. Cut excess cord
leaving enough length to reach from each end to center cord to assure
that the connections of each of the 3 cords and house wiring can be
made. Remove the outer jacket of each cord (M) to expose individual
wires (white, black, green). Strip half an inch of jacket away from the
ends of each individual wire.
Have a helper support the xture’s weight while completing the
wiring. Attach the xture’s wires [from all 3 cords (M)] to the power
supply wires from the junction box. Connect black to black (Live); white
to white (grounded); grounding to grounding (green or copper). Twist
the ends of the wire pairs together. Then, twist on a wire connector.
Make sure all twists are in the same direction. Loop xture’s ground
wire around grounding screw (E) and tighten. If there is no ground wire (green or copper) from the junction box,
contact a qualied electrician.
Raise canopy (F) to mounting plate (B) and position mounting screws (A) so that they protrude through the openings of
canopy (F). Secure canopy (F) in place with decorative nuts (L). Adjust alignment before installing glass. Secure glass (P)
onto the socket (O) with screws (N). Install light bulb (not included) in accordance with the xture’s specications. Do
not exceed the recommended wattage. Your installation is now complete. Turn on the power and test the xture.