MSDS

MSDS-001 - Issue Date: 1-16-05
Material Safety Data Sheet (MSDS)
PRODUCT AND COMPANY IDENTIFICATION
Description: Trade Name (as labeled) TCP SpringLamps or Circline (For general lighting
application). Consists of lamp ballast / adapter as a unit or lamp alone, no ballast / adapter.
Manufacturer: Technical Consumer Products, Inc.
325 Campus Drive | Aurora, Ohio 44202 | 1-800-324-1496
COMPOSITION/INFORMATION ON INGREDIENTS
THERE ARE NO KNOWN HEALTH HAZARDS FROM EXPOSURE TO LAMPS THAT ARE INTACT.
PHYSICAL PROPERTIES Not applicable to intact lamp.
EXPLOSION HAZARDS When exposed to high temperature, toxic fumes may be released from broken lamps.
Mercury
Phosphor
Glass
Inhalation
Ingestion
Contact
Eye/Skin
INFORMATION AND APPLICABILITY
Technical Consumer Products believes that under the Occupational Safety and Health
Administration (OSHA) Hazards Communications Standard, a lamp (light bulb) is exempted as
an “article”, and that as such, does not require an MSDS. The original OSHA Standard defined
an article as something that: 1) is formed to a specific shape and design, 2) has end use
functions dependent upon its shape and design, and 3) does not release or otherwise result in
an exposure to a hazardous chemical under normal conditions of use. In February 1994, OSHA
amended the Hazard Communication Standard and modified part 3 of the above to read: 3)
does not release more than very small quantities of a hazardous chemical under normal
conditions of use. State and local regulations also contain similar exemptions for such articles.
Materials contained in the lamp are not released during normal use and operation. The
following information is provided as a courtesy to our customers.
PROCEDURES FOR DISPOSAL OF LAMPS
Take usual precautions for collection of broken glass. Place materials in closed containers to avoid generating dust. A Toxicity Characteristic Leaching
Procedure (TCLP) was conducted on these products showing a result of mercury content that is not considered hazardous waste. For field disposal the
lead in the soldering is considered hazardous waste and must be disposed of by applicable federal, state and local regulations.
ALTHOUGH TECHNICAL CONSUMER PRODUCTS, INC. attempts to provide current and accurate information herein, it makes no representation
regarding the accuracy of completeness of the information and assumes no liability for any loss, damage or injury of any kind which may result from
or arise out of the use of/or reliance on the information by any person.
Lamp Assembly – Glass and Metal – The glass is made from soda lime similar to that used throughout the glass industry for other common consumer
items. The metals for end caps and filaments are generally made from various amounts of aluminum, tin, lead, copper, zinc, and nickel. None of these
materials would present a potential hazard in the event of breakage of the lamp, aside from the hazard due to broken glass.
The mercury in the air as a result of breaking one or a small number of fluorescent lamps should not result in significant exposures to an
individual. However, when breaking a large number of lamps for disposal, appropriate industrial hygiene monitoring and controls should be
implemented to minimize airborne levels or surface contamination. We recommend a well-ventilated area, and local exhaust ventilation or
personal protective equipment.
Glass dust is considered to be physiologically inert and as such has an OSHA exposure limit of 15-mg/cubic meter for total dust and
5-mg/cubic meter for
respirable dust. Perform normal first aid procedures. Seek medical attention as required.
If discomfort, irritation of symptoms of pulmonary involvement should develop, remove from exposure and seek medical attention.
In the unlikely event of ingestion of a large quantity of material, seek medical attention.
Wash eyes/skin, including under eyelids, immediately with copious amounts of water and seek medical attention.
There have been no significant adverse effects on humans by ingestion, inhalation, skin contact, or eye contact. Antimony, manganese, yttrium
and tin compounds are characterized by OSHA as hazardous chemicals, however, due to their insolubility, relatively low toxicity and small
amount present in the phosphor and lamp, these materials do not present a significant hazard in the event of breakage of the lamp.
Mercury – Small amounts of mercury is used in all fluorescent lamps. Generally around 0.025% by weight. The amount of mercury present in any given
lamp will vary depending on both the size of the lamp and on the equipment that was used in its manufacture. TCP continues to reduce the amounts of
mercury used in fluorescent products.
HEALTH CONCERNS THERE ARE NO KNOWN HEALTH HAZARDS FROM EXPOSURE TO LAMPS THAT INTACT. No adverse effects
are expected from occasional exposure to broken lamps. As a matter of good practice, avoid prolonged or frequent exposure to broken lamps unless
there is adequate ventilation. The major hazard form broken lamps is the possibility of sustaining glass cuts.
Phosphor – (nuisance dust) phosphate mix using manganese, rare earth elements such as lanthanum, and yttrium as either an oxide or as a phosphate,
along with a barium/aluminum oxide all are tightly bound in the phosphor matrix. These phosphors produce better lamp efficiency and color rendition. The
phosphor components may vary slightly depending on the color of the lamp. Some lamps may contain a thin coating of tin oxide inside the glass.
Compact Fluorescent Lamps – Spring Lamps, Floods, Globes, A-Bulbs, Torpedoes, Circline and PL Lamps
Compact Fluorescent Safety Specifications
©TCP, Inc. 2009/40495
TCP, Inc.
325 Campus Dr. | Aurora, Ohio 44202 | P: 1-800-324-1496 | F: 330-995-6188 | tcpi.com

Summary of content (1 pages)