Instruction Manual

LLATION INSTRUCTIONS FOR HUNTER CEILING FAN

LIGHT MODELS 26610 - 26619 SERIES

READ AND SAVE THESE INSTRUCTIONS

CAUTION:

1. TO REDUCE THE RISK OF FIRE AND ELECTRICAL SHOCK, INSTALL THIS LIGHT KIT ONLY ON LISTED

HUNTER CEILING FANS TYPE A THRU Z.

2. READ ENTIRE INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION

3. TO AVOID POSSIBLE ELECTRICAL SHOCK, BE CERTAIN ELECTRICITY IS TURNED OFF AT FUSE OR CIRCUIT

BREAKER PANEL BEFORE WIRING.

4. ALL WIRING MUST BE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES. IF YOU ARE

UNFAMILIAR WITH WIRING, YOU SHOULD USE A QUALIFIED ELECTRICIAN.

PRELIMINARY STEPS

(SEE FIG. 1)

INSERT PIPE NIPPLE (TDP DF LAMP SPCKET) THRDUGH CENTER HDLE IN FITTER.

PLACE LDCKWASHER AND NUT DN PIPE NIPPLE. (FINGER TIGHTEN BNLY)

REMDVE ENDBELL FRDM PULLCHAIN AND FEED THRDUGH BELMPUTH NUT. ALIGN SOCKET WITH

BELMDUTH NUT. TIGHTEN NUT DN PIPE NIPPLE.

REATTACH ENDBELL TD PULLCHAIN.

CONNECT WIRES TO FAN

(SEE FIG. 2)

NOTE:

* SEE FAN INSTALLATION INSTRUCTIONS FOR CONNECTING HOUSE WIRING TO THE FAN.

* CONNECT HOUSE WIRING TO THE FAN BEFORE ATTACHING THE FAN LIGHT TO THE FAN.

* SEE WIRING DIAGRAMS ON REVERSE SIDE FOR FAN LIGHT USE WITH WALL SWITCHES.

DISCONNECT POWER TD CEILING FAN AT THE MAIN PANEL.

REMDVE AND DISCARD SWITCH HOUSING COVER PLATE (IF INCLUDED) FRDM FAN. RETAIN THE SCREWS.

MAKE ELECTRICAL CONNECTIONS. SEE DIAGRAMS DN REVERSE SIDE.

INSTALL SWITCH HOUSING COVER SCREWS BACK ONTO SWITCH HOUSING. LEAVE SPACE UNDER THE

SCREW HEADS FOR THE FAN LIGHT. ASSEMBLE FAN LIGHT TO SWITCH HOUSING AND TURN COUNTER

CLOCKWISE SO THAT THE SCREWS SLIP INTO THE KEYHOLE SLOTS. TIGHTEN SCREWS.

ASSEMBLE LAMP BULB TD FAN LIGHT, USE 3-WAY LAMP BULB NO LARGER THAN 50/100/150 WATTS,

ASSEMBLE THUMB SCREWS (PROVIDED) TD GLOBE FITTER. ASSEMBLE SILENCER BAND (PROVIDED)

TD GLASS GLOBE (SOLD SEPARATELY). TIGHTEN SCREWS.

7. RECONNECT POWER TD COMPLETE INSTALLATION.

8. CAUTION IF GLOBE BEGINS TO BUZZ, CHECK TO MAKE CERTAIN THE GLOBE SCREWS ARE TIGHT.

9. ANYTIME THE GLOBE IS REMOVED AND REASSEMBLED, THE GLOBE FITTER SCREWS MUST BE CHECKED

FDR TIGHTNESS.

FORM NO.

SIDE 1

41367-01 2/98

PAGE 1
LLATION INSTRUCTIONS FOR HUNTER CEILING FAN LIGHT MODELS 26610 - 26619 SERIES READ AND SAVE THESE INSTRUCTIONS CAUTION: 1. TO REDUCE THE RISK OF FIRE AND ELECTRICAL SHOCK, INSTALL THIS LIGHT KIT ONLY ON LISTED HUNTER CEILING FANS TYPE A THRU Z. 2. READ ENTIRE INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION 3. TO AVOID POSSIBLE ELECTRICAL SHOCK, BE CERTAIN ELECTRICITY IS TURNED OFF AT FUSE OR CIRCUIT BREAKER PANEL BEFORE WIRING. 4.
PAGE 2
WIRING WITH WALL SWITCHES FAN AND LIGHT KIT CAN BE CONNECTED THROUGH WALL SWITCHES, THIS CAN BE DONE IN TWO WAYS; 1. USING ONE WALL SWITCH TO CONTROL BOTH FAN AND LIGHT. INDIVIDUAL CONTROL OF EITHER FAN OR LIGHT IS DONE WITH THE PULL CHAIN SWITCHES. 2. USING TWO WALL SWITCHES TO INDIVIDUALLY CONTROL BOTH FAN AND LIGHT - ONE FOR THE FAN AND THE SECOND FOR THE LIGHT. PULL CHAIN SWITCHES ON THE FAN DO NOT HAVE TO BE USED. SELECT THE TYPE OF CONTROL DESIRED AND WIRE THE UNIT PER ONE OF THE DIAGRAMS SHOWN BELOW.
PAGE 3
SUPPLEMENTARY INSTRUCTIONS FOR ATTACHING LIGHT KIT TO REMOTE CONTROL FAN • Be sure power is turned off. • Remove the switch housing from the fan by first removing the screw in the round hole in the switch housing top cover. Then loosen the remaining two screws so the switch housing can be twisted free of engagement with the switch housing top cover. Unplug the remote control module and remove the entire assembly from the fan. • Remove the center plug from the bottom of the switch housing.